Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub

Splines are used if,

(A) The power to be transmitted is high

(B) The torque to be transmitted is high

(C) The speed is high

(D) There is relative motion between shaft and hub
by

1 Answer

Answer :

(D) There is relative motion between shaft and hub
by

Related questions

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Last Answer : (C) Eight times that of B

Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Description : Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Last Answer : (C) (dA/dB-)3

The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)

Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)

Last Answer : 4. 2(shaft diameter)

The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)

Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)

Last Answer : (D) 2 (shaft diameter)

The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Last Answer : b) False

Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Last Answer : b) Radial

Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Last Answer : b) Radial

In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above

Description : In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above

Last Answer : (C) The keyway is cut in both the shaft and the hub

The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Last Answer : b) False

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

Splines are keys. a) True b) False

Description : Splines are keys. a) True b) False

Last Answer : a) True

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

Splines are keys. a) True b) False

Description : Splines are keys. a) True b) False

Last Answer : a) True

Splines are commonly used in (A) Machine tool gear box (B) Automobile gear box (C) Hoist and crane gear box (D) Bicycle

Description : Splines are commonly used in (A) Machine tool gear box (B) Automobile gear box (C) Hoist and crane gear box (D) Bicycle

Last Answer : (B) Automobile gear box

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Description : Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Last Answer : b) False

Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Description : Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Last Answer : b) False

Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Last Answer : d) Frictional torque is given by fpr2l

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Description : The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Last Answer : (C) Varies exponentially, being more near the torque-input end

The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Last Answer : (A) T/2

A shaft turns at 150 rpm under a torque of 1500 N-m. Power transmitted is (a) 15p kW (b) 10p kW (c) 7.5p kW (d) 5p kW (IES 1999) Hint: P = 2pNT/60

Description : A shaft turns at 150 rpm under a torque of 1500 N-m. Power transmitted is (a) 15p kW (b) 10p kW (c) 7.5p kW (d) 5p kW (IES 1999) Hint: P = 2pNT/60

Last Answer : (c) 7.5p kW

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Last Answer : (c) π/4fs(D4-d4)/D

The torque transmitted by a solid shaft is (a)π/4fsd3 (b) π/16fsd3 (c) π/32fsd3 (d) π/64fsd3

Description : The torque transmitted by a solid shaft is (a)π/4fsd3 (b) π/16fsd3 (c) π/32fsd3 (d) π/64fsd3

Last Answer : (b) π/16fsd3

When the torque required by the machine is more than the torque supplied by the motor, the flywheel is (A) Accelerated (B) Retarded (C) Rotating with constant speed (D) Any of the above

Description : When the torque required by the machine is more than the torque supplied by the motor, the flywheel is (A) Accelerated (B) Retarded (C) Rotating with constant speed (D) Any of the above

Last Answer : (B) Retarded

Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) Bearing vibration, oil pressure and speed of shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration

Description : Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) ... shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration

Last Answer : Oil pressure, bearing metal temperature and bearing vibration

Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the statements given above are correct? (a) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Description : Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the ... ) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Last Answer : (b) Only 1 and 2

Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the using the code given below: (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Description : Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the ... 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Last Answer : (b) 1 and 3 only

For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply supported beam fixed at hub and rim and carrying uniformly distributed load 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load

Description : For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply ... tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load

Last Answer : 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim

For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply supported beam fixed at hub and rim and carrying uniformly distributed load (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load

Description : For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply ... tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load

Last Answer : (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim

Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2

Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2

Last Answer : c) 4.84N/mm2

A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Description : A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Last Answer : a) Hub

Sunk key fits in the keyway of the .......... only. A. Sleeve B. Hub C. Both sleeve and hub D. neither sleeve and hub

Description : Sunk key fits in the keyway of the .......... only. A. Sleeve B. Hub C. Both sleeve and hub D. neither sleeve and hub

Last Answer : B. Hub

A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Description : A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Last Answer : a) Hub

The key, which fits in the keyway of hub, only is called, (A) Saddle key (B) Feather key (C) Woodruff key (D) Kennedy key

Description : The key, which fits in the keyway of hub, only is called, (A) Saddle key (B) Feather key (C) Woodruff key (D) Kennedy key

Last Answer : (A) Saddle key

Power is transmitted by only in rigid flange coupling. a) True b) False

Description : Power is transmitted by only in rigid flange coupling. a) True b) False

Last Answer : b) False

In case of clamp coupling, power is transmitted by means of, (A) Friction force (B) Shear resistance (C) Crushing resistance (D) None of the above

Description : In case of clamp coupling, power is transmitted by means of, (A) Friction force (B) Shear resistance (C) Crushing resistance (D) None of the above

Last Answer : (A) Friction force

Power is transmitted by only in rigid flange coupling. a) True b) False

Description : Power is transmitted by only in rigid flange coupling. a) True b) False

Last Answer : b) False

Saddle key is transmit power or torque through friction resistant only A. True B. False

Description : Saddle key is transmit power or torque through friction resistant only A. True B. False

Last Answer : A. True

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Description : When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Last Answer : 1. Accelerated