If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

If the lateral force acting on the set screw is large and tends to displace one part with respect to

other than which point is recommended?

a) Dog Point

b) Cone Point

c) Window Point

d) Cut Point
by

1 Answer

Answer :

a) Dog Point
by

Related questions

In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same

Description : In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same

Last Answer : (A) shorten the spring

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Last Answer : b. Set screws

For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Description : For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Last Answer : b) False

Which among the following is the condition to avoid separation of connected members? a. Force acting on the connected members should be negative b. Force acting on the connected members should be positive c. Force acting on the connected members should be neither positive nor negative d. None of the above

Description : Which among the following is the condition to avoid separation of connected members? a. Force acting on the connected members should be negative b. Force acting on the connected members should be ... acting on the connected members should be neither positive nor negative d. None of the above

Last Answer : a. Force acting on the connected members should be negative

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False

Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False

Last Answer : a) True

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty

Description : In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty

Last Answer : b) Increase with increase in speed

In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Description : In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Last Answer : b) False

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Description : Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Last Answer : a) 50%

Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Last Answer : a) decreases

Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Description : Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Last Answer : b) False

Efficiency of screw depends upon lead of the screw. a) True b) False

Description : Efficiency of screw depends upon lead of the screw. a) True b) False

Last Answer : a) True

Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Last Answer : b) False

Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Last Answer : d. all of the above

Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Description : Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Last Answer : (C) Cap screw with hexagonal socket head

A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Description : A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Last Answer : (A) Major diameter

The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Description : The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Last Answer : (A) Major diameter

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Description : The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Last Answer : (A) (1 - sinφ)/ (1 + sinφ)

A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Description : A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : A. Which are perfectly aligned

Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Description : Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : C. Which have lateral misalignment

A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Description : A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Last Answer : C. Whose axes intersect at a small angle

I come in a cone but I am not food;I will be skewed if you screw with my hue;I come by the millions but you can probably only name a few.What am I? -Riddles

Description : I come in a cone but I am not food;I will be skewed if you screw with my hue;I come by the millions but you can probably only name a few.What am I? -Riddles

Last Answer : Colors.

Split flywheel is made to 1. avoid cooling stress 2. reduce weight 3. increase weight 4. maximize large centrifugal force

Description : Split flywheel is made to 1. avoid cooling stress 2. reduce weight 3. increase weight 4. maximize large centrifugal force

Last Answer : 1. avoid cooling stress

Which type of joints is better when the product is subjected to large vibrations: welded or threaded? a) Welded b) Threaded c) Both have same results d) Depends on the magnitude of the vibrational force

Description : Which type of joints is better when the product is subjected to large vibrations: welded or threaded? a) Welded b) Threaded c) Both have same results d) Depends on the magnitude of the vibrational force

Last Answer : a) Welded

Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False

Description : Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False

Last Answer : b) False

Which type of threads is recommended for fluctuating loads? a) Fine threads b) Coarse Threads c) Either of fine or coarse d) None of the listed

Description : Which type of threads is recommended for fluctuating loads? a) Fine threads b) Coarse Threads c) Either of fine or coarse d) None of the listed

Last Answer : a) Fine threads

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

Distortion energy theorem is not recommended for ductile materials. a) True b) False

Description : Distortion energy theorem is not recommended for ductile materials. a) True b) False

Last Answer : b) False

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

Distortion energy theorem is not recommended for ductile materials. a) True b) False

Description : Distortion energy theorem is not recommended for ductile materials. a) True b) False

Last Answer : b) False

If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but governor will not operate (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Description : If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but ... (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Last Answer : (A) The governor will not operate but flywheel will be acting

The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm<5 (c) rotating at rpm<10 (d) rotating at rpm<15

Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm

Last Answer : (a) stationary

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

Hydrodynamic bearing is a self-acting bearing. a) True b) False

Description : Hydrodynamic bearing is a self-acting bearing. a) True b) False

Last Answer : a) True

Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm<10 c) Rotating at rpm<5 d) None of the listed

Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm

Last Answer : a) Stationary

A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Last Answer : a) Thrust

Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above

Description : Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above

Last Answer : b. intensity of direct stress

What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Last Answer : c. 39.60 Mpa

Principal stress is the magnitude of ________ stress acting on the principal plane. a. Normal stress b. Shear stress c. Both a. and b. d. None of the above

Description : Principal stress is the magnitude of ________ stress acting on the principal plane. a. Normal stress b. Shear stress c. Both a. and b. d. None of the above

Last Answer : a. Normal stress

To displace a cubic foot of fresh water, you need _________ force.  a. 62.4 lb  b. 9.81 lb  c. 76 lb  d. 760 lb

Description : To displace a cubic foot of fresh water, you need _________ force.  a. 62.4 lb  b. 9.81 lb  c. 76 lb  d. 760 lb

Last Answer : 62.4 lb

The problems for criticism about large dams are that they A. Displace large number of peasants and trebles without proper rehabilitation B. Swallow up huge amounts of public money without the generation of proportionate benefits C. Contribute enormously to deforestation and the loss of biological diversity D. All of the above.

Description : The problems for criticism about large dams are that they A. Displace large number of peasants and trebles without proper rehabilitation B. Swallow up huge amounts of public money without the ... Contribute enormously to deforestation and the loss of biological diversity D. All of the above.

Last Answer : D. All of the above.