Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False
Last Answer : b) False
Description : The maximum shear stress occurs on the filament which makes an angle with the horizontal plane equal to (A) 30° (B) 45° (C) 60° (D) 90
Last Answer : (B) 45°
Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed
Last Answer : a) PSinθ(Sinθ+Cosθ)/hl
Description : For determining the support reactions at A and B of a three hinged arch, points B and Care joined and produced to intersect the load line at D and a line parallel to the load line through A at D'. Distances AD, DD ... reactions at A and B is (A) 30° (B) 45° (C) 60° (D) 90
Last Answer : (D) 90
Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed
Last Answer : b) 1.21P/hl
Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed
Last Answer : a) Leg
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : The angle between two plane mirrors of optical square, is (A) 20° (B) 30° (C) 45° (D) 60°
Last Answer : (C) 45°
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False
Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed
Last Answer : a) t =h Cos (45’)
Description : If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel
Last Answer : d) Longitudinal or Parallel
Description : The angle in which a cricket ball should be hit to travel maximum horizontal distance is : (1) 60° with horizontal (2) 45° with horizontal (3) 30° with horizontal (4) 15° with horizontal
Last Answer : (2) 45° with horizontal Explanation: This has to do with the equation of a parabola or trajectory which is z = (tane)x 2 cos 9) 2. We can see that if the ball is fired at a 45 degree angle from the ground, the horizontal distance will be a maximum.
Description : A projectile is fired at an angle to the vertical. Its horizontal range will be maximum when is (A) 0° (B) 30° (C) 45° (D) 60°
Last Answer : 45° with horizontal
Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld
Last Answer : (c) 2 × Throat of weld
Description : Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None
Last Answer : (i) Shear stress
Description : Parallel fillet welds are under Shear and bending stresses Compressive and torsion shear stresses Tensile and compressive stresses None
Last Answer : None
Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength
Last Answer : (d) shear strength
Description : If a cohesive soil specimen is subjected to a vertical compressive load, the inclination of the cracks to the horizontal is (A) 90° (B) 45° (C) 22.5° (D) 0
Description : The angle of minimum deviation of an equiangular prism, having a refractive index of 1.732 is (a) 60° (b) 30° (c) 45° (d) 0°
Last Answer : Ans:(a)
Description : The value of 2 tan 2 45°+ cos 2 30° − sin 2 60° is (a) 0 (b) 1 (c) -2 (d) 2
Last Answer : (d) 2
Description : sin 2A = 2 sin A is true when A = a 30° b 45° c 0° d 60°
Last Answer : a 0
Description : The angle of intersection of a contour and a ridge line, is (A) 30° (B) 45° (C) 60° (D) 90°
Last Answer : (D) 90°
Description : A well conditioned triangle has no angle less than (A) 20° (B) 30° (C) 45° (D) 60°
Last Answer : (B) 30°
Description : The zone in which transverse bending is likely to occur may be obtained by drawing a line from the (A) 30° (B) 45° (C) 60° (D) None of these
Last Answer : Answer: Option B
Description : The helix angle for double helical gears may be made up to (A) 45° (B) 60° (C) 75° (D) 90°
Last Answer : (A) 45°
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False
Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None
Last Answer : c. Triangular
Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None
Last Answer : c. 45 0
Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None
Last Answer : b. 0.707x leg
Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None
Last Answer : (i)0.707 tl
Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.
Last Answer : (a) butt weld
Description : A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False
Description : Maximum number of vehicles can be parked with (A) Parallel parking (B) 30° angle parking (C) 45° angle parking (D) 90° angle parking
Last Answer : Answer: Option D
Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None
Last Answer : (iv)None
Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress
Last Answer : (iii) Tensile stress
Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength
Last Answer : (a) tensile strength
Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°
Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.
Last Answer : (d) never be across the threaded portion
Description : Joint which does not fall under lap joint category (i)Transverse fillet (ii) Parallel fillet (iii) Circular fillet (iv) None
Last Answer : (iv) None
Description : In stone masonry, stones (stratified rocks) are so placed that the direction of pressure to the plane of bedding is (A) Right angles (B) 45° (C) 60° (D) Paralle
Last Answer : Answer: Option A
Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate
Last Answer : (a) 1.5 mm less than the plate thickness
Description : The screens are fixed A. Perpendicular to the direction of flow B. Parallel to the direction of flow C. At an angle 30° to 60° to the direction of flow D. None of these
Last Answer : ANS: C
Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data
Last Answer : c. 39.60 Mpa
Description : For the manufacture of plywood, veneers are placed so that grains of adjacent veneers (A) Run at right angles (B) Parallel (C) Inclined at 45° (D) Inclined at 60°
Description : Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress
Last Answer : a. Resultant stress on any plane in a bi-axial stress system
Description : The angle between a principal plane and a plane of maximum shear is a. 15 0 b. 45 0 c. 75 0 d. None
Last Answer : b. 45 0