For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to
(a) 1.5 mm less than the plate thickness
(b) 67% of the plate thickness
(c) 80% of the plate thickness
(d) Thickness of the plate
by

1 Answer

Answer :

(a) 1.5 mm less than the plate thickness
by

Related questions

For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Last Answer : Answer: Option D

Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Description : Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Last Answer : iii. 5/8”

In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (c) 2 × Throat of weld

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Description : Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Last Answer : iii. 3/8”

For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at (a) 22.5° (b) 30° (c) 45° (d) 60°

Description : For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at (a) 22.5° (b) 30° (c) 45° (d) 60°

Last Answer : (c) 45°

Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Last Answer : b) False

Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Last Answer : c. Triangular

In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Description : In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Last Answer : (B) Between 300 mm and 750 mm

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Last Answer : a) Leg

Four equal sized maximum circular plates are cut off from a square sheet of area 784 cm2. What is the circumference of each plate? a) 22 cm b) 44 cm c) 42 cm d) 40cm

Description : Four equal sized maximum circular plates are cut off from a square sheet of area 784 cm2. What is the circumference of each plate? a) 22 cm b) 44 cm c) 42 cm d) 40cm

Last Answer : b) 44 cm

A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm

Description : A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of ... (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm

Last Answer : Answer: Option B

Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and 40,000 psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Description : Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and ... psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Last Answer : b) The hub thickness at the welding end and 40,000 psi yield strength

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

Which of the following phrases completes the following statement: The strength of the electric field between two oppositely charged parallel plates is: w) a maximum midway between the plates x) a maximum near the positively charged plate y) constant between the plates except near the edges z) zero midway between the plates

Description : Which of the following phrases completes the following statement: The strength of the electric field between two oppositely charged parallel plates is: w) a maximum midway between the plates x) a maximum ... plate y) constant between the plates except near the edges z) zero midway between the plates

Last Answer : ANSWER: Y -- CONSTANT BETWEEN THE PLATES EXCEPT NEAR THE EDGES

A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False

Description : A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False

Last Answer : b) False

Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Last Answer : b) False

A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Last Answer : b) False

The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Last Answer : c. 45 0

Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Last Answer : b. 0.707x leg

Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Last Answer : (i)0.707 tl

Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Last Answer : a) t =h Cos (45’)

If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel

Description : If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel

Last Answer : d) Longitudinal or Parallel

A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Last Answer : (a) butt weld

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3

Description : The maximum load to which a fillet joint of length can be subjected to, is  (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3 

Last Answer : (A) 0.7 × S × fillet size × L

Which one of the following activities is not correct as applicable to brick corbels? (A) The maximum projection of the corbel should not be more than the thickness of the wall (B) The maximum projection of each corbel course should be limited to a quarter brick at a time (C) The discontinuous corbels are used to carry heavy concentrated loads (D) Stretcher bond is generally used for the construction of brick corbel

Description : Which one of the following activities is not correct as applicable to brick corbels? (A) The maximum projection of the corbel should not be more than the thickness of the wall (B) The ... to carry heavy concentrated loads (D) Stretcher bond is generally used for the construction of brick corbel

Last Answer : Answer: Option D

A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Last Answer : (C) 50 mm

The ratio of the moment of inertia of a circular plate and that of a square plate for equal depth, is (A) Less than one (B) Equal to one (C) More than one (D) Equal

Description : The ratio of the moment of inertia of a circular plate and that of a square plate for equal depth, is  (A) Less than one  (B) Equal to one  (C) More than one  (D) Equal 

Last Answer : (D) Equal 

The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (ii) Butt welded joint

By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (i) Fillet welded joint

The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Description : The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Last Answer : d/85

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Last Answer : Answer: Option B

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

The compressive strength of 100 mm cube as compared to 150 mm cube is always (A) Less (B) More (C) Equal (D) None of the above

Description : The compressive strength of 100 mm cube as compared to 150 mm cube is always (A) Less (B) More (C) Equal (D) None of the above

Last Answer : Answer: Option B

What is the value of co-efficient of discharge for square edged circular orifice (for β = 0.3 to 0.5)? (A) 0.61 - 0.63(B) 0.5 - 0.75 (C) 0.75 - 0.90 (D) 0.35 - 0.55

Description : What is the value of co-efficient of discharge for square edged circular orifice (for β = 0.3 to 0.5)? (A) 0.61 - 0.63 (B) 0.5 - 0.75 (C) 0.75 - 0.90 (D) 0.35 - 0.55

Last Answer : (A) 0.61 - 0.63

The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm

Description : The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm

Last Answer : Answer: Option B

The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Lesser of (a) and (b)

In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Description : In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Last Answer : b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate

How much dirt would be in a hole 6 feet deep and 6 feet wide that has been dug with a square edged shovel?

Description : How much dirt would be in a hole 6 feet deep and 6 feet wide that has been dug with a square edged shovel?

Last Answer : None. No matter how big a hole is, it's still a hole: the absence of dirt.

Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should be multiplied with __________ to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Description : Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should ... to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Last Answer : (C) 1.34

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Description : The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Last Answer : [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm