Description : The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld
Last Answer : (b) Throat of weld
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed
Last Answer : a) Leg
Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None
Last Answer : (i)0.707 tl
Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None
Last Answer : b. 0.707x leg
Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength
Last Answer : (a) tensile strength
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Last Answer : b) False
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False
Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False
Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False
Description : If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel
Last Answer : d) Longitudinal or Parallel
Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed
Last Answer : b) 1.21P/hl
Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed
Last Answer : a) PSinθ(Sinθ+Cosθ)/hl
Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed
Last Answer : a) t =h Cos (45’)
Description : Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None
Last Answer : iii. 5/8”
Description : The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None
Last Answer : (ii) Butt welded joint
Description : By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None
Last Answer : (i) Fillet welded joint
Description : Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None
Last Answer : iii. 3/8”
Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength
Last Answer : (d) shear strength
Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.
Last Answer : (a) butt weld
Description : Joint which does not fall under lap joint category (i)Transverse fillet (ii) Parallel fillet (iii) Circular fillet (iv) None
Last Answer : (iv) None
Description : For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at (a) 22.5° (b) 30° (c) 45° (d) 60°
Last Answer : (c) 45°
Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None
Last Answer : c. 45 0
Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed
Last Answer : a) My/I
Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None
Last Answer : c. Triangular
Description : A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False
Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None
Last Answer : (iv)None
Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress
Last Answer : (iii) Tensile stress
Description : If length of weld is l and leg h, then area of throat can be given by a) 0.707 hl b) 1.414hl c) hl d) None of the listed
Last Answer : a) 0.707 hl
Description : The strength of a welded joint with respect to a riveted joint is a. Greater b. Smaller c. Equal d. None
Last Answer : a. Greater
Description : Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater
Last Answer : c. Greater
Description : The angle of V-welded joint in a pressure vessel 30 to 45 0 40 to 55 0 55 to 70 0 None
Last Answer : 55 to 70 0
Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate
Last Answer : (a) 1.5 mm less than the plate thickness
Description : Welded joints are a. Hinged joint b. Rigid joint c. Freely supported joint
Last Answer : b. Rigid joint
Description : Welded structures with respect to riveted joint is a. Weakened in tension b. Strengthened in tension c. No change in tension strength d. None
Last Answer : c. No change in tension strength
Description : Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None
Last Answer : (ii) Lap joint
Description : Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None
Last Answer : (i) Butt joint
Description : The advantage of a welded joint over a riveted joint is (i) Introduce residual stresses (ii) Requires highly skilled labor and supervision (iii) Lighter in weight (iv) None
Last Answer : (iii) Lighter in weight
Description : Internal defects in a welded joint can be found by a process called (i) Tension test (ii) Visual inspection (iii) Radio graphing (iv) None
Last Answer : (iii) Radio graphing
Description : One which is applicable to a welded joint (i)Less rigidity (ii) Heavy (iii) Difficult process (iv) None
Description : Term which is not applicable to a welded joint (i) Higher efficiency (ii)Easy process (iii) Faster process
Last Answer : (ii)Easy process
Description : Type of welded joint which do not exit (i) Groove type (ii) Spot type (iii)Plug type (iv) Surface type
Last Answer : (iv) Surface type
Description : Out of the followings, which welded joint is more stronger (i) Butt joint (ii) Lap joint (iii)Screwed joint
Description : Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None
Last Answer : i. Longitudinal stress
Description : Longitudinal welded joint fails by Longitudinal stress Radial stress Hoop stress None
Last Answer : Hoop stress
Description : Welded joint strength increases due to annealing by i. 6% ii. 10% iii. 14% iv. None
Last Answer : i. 6%
Description : Strength of a welded joint increases by radio graphing by i. 10 % ii. 12% iii. 15% iv. None
Last Answer : ii. 12%
Description : The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False