The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

The resultant axial force on bolt depends upon

(A) Initial tension

(B) External applied load

(C) Stiffness of bolt and parts held by bolt

(D) All three factors
by

1 Answer

Answer :

(D) All three factors
by

Related questions

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (D) Force required to produce unit deflection

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress

Description : Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress

Last Answer : a. Resultant stress on any plane in a bi-axial stress system

In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Description : In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Last Answer : b) False

The internal molecular attraction of a soil, the cohesion (A) Decreases as the moisture content increases (B) Increases as the moisture content decreases (C) Is more in well compacted clays (D) Depends upon the external applied load

Description : The internal molecular attraction of a soil, the cohesion (A) Decreases as the moisture content increases (B) Increases as the moisture content decreases (C) Is more in well compacted clays (D) Depends upon the external applied load

Last Answer : Answer: Option C

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

A spring of stiffness constant k is cut in two equal parts. The stiffness constant of new spring will be k/2. a) True b) False

Description : A spring of stiffness constant k is cut in two equal parts. The stiffness constant of new spring will be k/2. a) True b) False

Last Answer : b) False

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

The angle of friction is a.The angle which frictional force makes with the normal b.The anle at which the force applied from external souce will cause movement c.The angle at which fictional force is inclined to external force d.The angle between the normal reaction and the resultant of normal reaction and the limiting friction e.None of the above

Description : The angle of friction is a.The angle which frictional force makes with the normal b.The anle at which the force applied from external souce will cause movement c.The angle at which fictional ... the normal reaction and the resultant of normal reaction and the limiting friction e.None of the above

Last Answer : d. The angle between the normal reaction and the resultant of normal reaction and the limiting friction

The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Description : The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Last Answer : (D) all of the above

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Last Answer : b) Thrust load

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Last Answer : C. Axial tensile or compressive load

Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Last Answer : C. Axial tensile or compressive load

What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Last Answer : c. 39.60 Mpa

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

Stressed parts are always kept in tension. a) True b) False

Description : Stressed parts are always kept in tension. a) True b) False

Last Answer : a) True

A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of maximum compession of spring, neglecting friction to that while considering friction would be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Last Answer : a. More than one

Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco-elastic material, stress-strain relation is dependent on time (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Last Answer : (D) All the above

Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the statements given above are correct? (a) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Description : Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the ... ) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Last Answer : (b) Only 1 and 2

Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Description : Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Last Answer : b) False

Efficiency of screw depends upon lead of the screw. a) True b) False

Description : Efficiency of screw depends upon lead of the screw. a) True b) False

Last Answer : a) True

The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Last Answer : (d) never be across the threaded portion

If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm

Description : If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm

Last Answer : a) 17.27mm

The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Last Answer : d) None of the listed

The shock absorbing capacity of bolt can be increased by making the shank diameter ________ the root diameter. a) Lesser than b) Equal to c) Greater than d) No effect

Description : The shock absorbing capacity of bolt can be increased by making the shank diameter ________ the root diameter. a) Lesser than b) Equal to c) Greater than d) No effect

Last Answer : b) Equal to

Shank is the portion of bolt between the head and the thread. a) True b) False

Description : Shank is the portion of bolt between the head and the thread. a) True b) False

Last Answer : a) True

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Last Answer : b. Set screws

The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Last Answer : (B) Making shank diameter equal to core diameter of threads

The shock absorbing capacity of a bolt can be increased by (A) Increasing stress in shank (B) Increasing stress in core diameter of threads (C) Decreasing stress in shank (D) Decreasing stress in core diameter of threads

Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing stress in shank (B) Increasing stress in core diameter of threads (C) Decreasing stress in shank (D) Decreasing stress in core diameter of threads

Last Answer : (A) Increasing stress in shank

When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (B) h = 0.25 dc

When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

Which of the following factors affect the mechanical properties of a material under applied loads? a) Content of alloys b) Grain size c) Imperfection and defects d) Shape of material

Description : Which of the following factors affect the mechanical properties of a material under applied loads? a) Content of alloys b) Grain size c) Imperfection and defects d) Shape of material

Last Answer : d) Shape of material

The statement the resultant of the external forces applied to a body (rigid or non-rigid) composed of a system of particles is equivalent to the vector summation of the effective forces acting on all particles-is known as a.Corollary to Newton's laws of motion b.Principle of dynamics c.D' Alembert's principle d.Nowton's law e.Mohr's principle

Description : The statement the resultant of the external forces applied to a body (rigid or non-rigid) composed of a system of particles is equivalent to the vector summation of the effective forces acting on all ... motion b.Principle of dynamics c.D' Alembert's principle d.Nowton's law e.Mohr's principle

Last Answer : c. D' Alembert's principle

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Description : A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Last Answer : (b) Y-Y axis