Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Which of the following is not a function of washer?

a) Distributes load over a large area of clamped parts

b) Provides bearing surface over large clearance bolts

c) Prevents marring of the bolt head and nut surface

d) Helps in locking of the fastener
by

1 Answer

Answer :

d) Helps in locking of the fastener
by

Related questions

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Description : In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Last Answer : b) False

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Description : The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Last Answer : (A) More

The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Last Answer : (B) Making shank diameter equal to core diameter of threads

When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Last Answer : (d) never be across the threaded portion

The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Last Answer : d) None of the listed

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Description : If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Last Answer : b) Tap Bolts

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (B) h = 0.25 dc

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size

Description : The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size

Last Answer : (B) More than the nut size

The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Description : The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Last Answer : (D) All three factors

The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it. (A) Tension (B) Shear (C) Compression (D) Bending & tension

Description : The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it. (A) Tension (B) Shear (C) Compression (D) Bending & tension

Last Answer : Option A

Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Description : Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Last Answer : a) All bolts are symmetrically spaced with equal angle on either side of vertical

Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated

Description : Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated

Last Answer : b) Tap Bolts

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the using the code given below: (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Description : Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the ... 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Last Answer : (b) 1 and 3 only

A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Last Answer : b) Journal radius is kept smaller

Shank is the portion of bolt between the head and the thread. a) True b) False

Description : Shank is the portion of bolt between the head and the thread. a) True b) False

Last Answer : a) True

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Description : Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Last Answer : Option B

Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Description : Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Last Answer : Option B

What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Description : What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Last Answer : (c) Superior load carrying capacity at higher speeds

Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Last Answer : d) All of the listed

Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Description : Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Last Answer : a) 50%

Self-locking takes place when a) Coefficient of friction is equal to or greater than the tangent of the helix angle b) Coefficient of friction is lesser than or equal to the tangent of the helix angle c) Coefficient of friction is equal to or greater than the tangent of the helix angle d) None of the mentioned

Description : Self-locking takes place when a) Coefficient of friction is equal to or greater than the tangent of the helix angle b) Coefficient of friction is lesser than or equal to the tangent of the helix ... friction is equal to or greater than the tangent of the helix angle d) None of the mentioned

Last Answer : c) Coefficient of friction is equal to or greater than the tangent of the helix angle

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Last Answer : (C) Key is the weakest component

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Last Answer : (B) 3 d

Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Last Answer : (b) corrosive

Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (d) Cage

Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (b) Outer race

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant

A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact

A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (D) Where there is no lubricant