Description : The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)
Last Answer : (A) (1 - sinφ)/ (1 + sinφ)
Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.
Last Answer : (d) never be across the threaded portion
Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt
Last Answer : a) Screw
Description : Which type of joints is better when the product is subjected to large vibrations: welded or threaded? a) Welded b) Threaded c) Both have same results d) Depends on the magnitude of the vibrational force
Last Answer : a) Welded
Description : Threaded joints are non-separable joints. a) True b) False
Last Answer : b) False
Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt
Last Answer : b. Set screws
Description : The region of safety in maximum shear stress theory contains which of the given shape a) Hexagon b) Rectangle c) Square d) None of the mentioned
Last Answer : a) Hexagon
Description : Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%
Last Answer : a) 50%
Description : The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square
Last Answer : a) Ellipse
Description : If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse
Last Answer : b) Square
Description : Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater
Last Answer : c. Greater
Description : Term which is not applicable to a welded joint (i) Higher efficiency (ii)Easy process (iii) Faster process
Last Answer : (ii)Easy process
Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined
Last Answer : a) decreases
Description : Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False
Description : Efficiency of screw depends upon lead of the screw. a) True b) False
Last Answer : a) True
Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above
Last Answer : d. all of the above
Description : The rated life of a bearing varies (a) directly as load (b) inversely as the square of the load (c) inversely as the cube of the load
Last Answer : (c) inversely as the cube of the load
Description : The rated life of a bearing varies A. Directly as load B. Inversely as square of load C. Inversely as cube of load D. Inversely as fourth power of load
Last Answer : C. Inversely as cube of load
Description : The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1
Last Answer : (D) 1
Description : The rated life of a bearing varies (A) Directly as load (B) Inversely as square of load (C) Inversely as cube of load (D) Inversely as fourth power of load
Last Answer : (C) Inversely as cube of load
Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring
Last Answer : (D) Square of wire diameter of each spring
Description : The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root
Last Answer : b) No, it is directly proportional
Description : Spring having square ends has 1 inactive coil. a) True b) False
Description : Plug weld is a. Rectangular b. Square c. Triangular d. None
Last Answer : d. None
Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None
Last Answer : c. Triangular
Description : Lap welded joints are a. Rectangular b. Square c. Triangular d. None
Description : Which of the following requires more space for the rotation of spanner? a) Square Head b) Hexagonal Head c) Both require equal space of rotation d) Cannot be stated
Last Answer : a) Square Head
Description : The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress
Last Answer : (C) Twice of shear stress
Description : The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d
Last Answer : (C) 1.5d
Description : In a flywheel the safe stress is 25.2MN/m 2 and the density is 7 g/cm 3 . Then what is the maximum peripheral velocity ? 1. 30m/s 2. 45m/s 3. 60m/s 4. 120m/s
Last Answer : 3. 60m/s
Description : Calculate the coefficient of fluctuation of speed if maximum speed is 2500rpm and minimum speed is 1800rpm. 1. 1.44 2. 1.33 3. 0.33 4. 0.44
Last Answer : 3. 0.33
Description : Reciprocal of coefficient of fluctuation of speed is called 1. fluctuation of energy 2. fluctuation of speed 3. maximum fluctuation of speed 4. coefficient of fluctuation of speed
Last Answer : 4. coefficient of fluctuation of speed
Description : Maximum fluctuation of energy = 1. Max KE – Min KE 2. Max KE + Min KE 3. Max KE > Min KE 4. Max KE < Min KE
Last Answer : 1. Max KE – Min KE
Description : The coefficient of fluctuation of speed of flywheel is 1. ratio of maximum and minimum speeds during the cycle 2. ratio of maximum fluctuation of speed to the mean speed 3. ratio of mean ... maximum fluctuation of speed during the cycle 4. sum of maximum fluctuation of speed and the mean speed
Last Answer : 2. ratio of maximum fluctuation of speed to the mean speed
Description : The coefficient of fluctuation of energy of flywheel is 1. ratio of maximum fluctuation of energy to work done per cycle 2. ratio of to work done per cycle to maximum fluctuation of energy ... minimum kinetic energy during the cycle 4. ratio of maximum and minimum kinetic energy during the cycle
Last Answer : 1. ratio of maximum fluctuation of energy to work done per cycle
Description : The maximum fluctuation of energy of flywheel is 1. difference between maximum and minimum kinetic energy during the cycle 2. difference between maximum and mean kinetic energy during the cycle 3. ... kinetic energy during the cycle 4. mean of maximum and minimum kinetic energy during the cycle
Last Answer : 1. difference between maximum and minimum kinetic energy during the cycle
Description : Maximum fluctuation of energy = (A) Max. KE – Min. KE (B) Max. KE + Min. KE (C) (Max. KE – Min. KE)/2 (D) (Max. KE + Min. KE)/2
Last Answer : (A) Max. KE – Min. KE
Description : The coefficient of fluctuation of speed, when the maximum and minimum speeds are 300rpm and 290 rpm (A) 0.034 (B) 0.017 (C) 0.008 (D) 0/004
Last Answer : (A) 0.034
Description : The coefficient of fluctuation of energy = (A) Maximum fluctuation of energy / work done per cycle (B) Fluctuation of energy / Work done per cycle (C) Maximum fluctuation of energy / Mean speed (D) Fluctuation of energy / Mean speed
Last Answer : (A) Maximum fluctuation of energy / work done per cycle
Description : Reciprocal of Coefficient of fluctuation of speed is called (A) Fluctuation of speed (B) Coefficient of steadiness (C) Maximum fluctuation of speed (D) None of the above
Last Answer : (B) Coefficient of steadiness
Description : The ratio of maximum fluctuation of speed to the mean speed is called (A) Fluctuation of speed (B) Maximum fluctuation of speed (C) Coefficient of fluctuation of speed (D) None of the above
Last Answer : (C) Coefficient of fluctuation of speed
Description : The difference the maximum and minimum speeds during a cycle is called (A) Fluctuation of speed (B) Maximum fluctuation of speed (C) Coefficient of fluctuation of speed (D) None of the above
Last Answer : (B) Maximum fluctuation of speed
Description : The coefficient of fluctuation of speed of flywheel is, (A) Ratio of maximum and minimum speeds during the cycle (B) Ratio of maximum fluctuation of speed to the mean speed (C) Ratio of ... maximum fluctuation of speed during the cycle (D) Sum of maximum fluctuation of speed and the mean speed
Last Answer : (B) Ratio of maximum fluctuation of speed to the mean speed
Description : The coefficient of fluctuation of energy of flywheel is, (A) Ratio of maximum fluctuation of energy to work done per cycle (B) Ratio of to work done per cycle to maximum fluctuation of ... minimum kinetic energy during the cycle (D) Ratio of maximum and minimum kinetic energy during the cycle
Last Answer : (A) Ratio of maximum fluctuation of energy to work done per cycle
Description : The maximum fluctuation of speed of flywheel is, (A) Difference between maximum and minimum speeds during the cycle (B) Difference between maximum and mean speeds during the cycle (C) Difference ... and minimum speeds during the cycle (D) Mean of maximum and minimum speeds during the cycle
Last Answer : (A) Difference between maximum and minimum speeds during the cycle
Description : The maximum fluctuation of energy of flywheel is, (A) Difference between maximum and minimum kinetic energy during the cycle (B) Difference between maximum and mean kinetic energy during the cycle ... kinetic energy during the cycle (D) Mean of maximum and minimum kinetic energy during the cycle
Last Answer : (A) Difference between maximum and minimum kinetic energy during the cycle
Description : The needle rollers are a maximum of _______ millimeter in diameter. (a) 4 (b) 5 (c) 6 (d) 7
Last Answer : (b) 5
Description : Different types of bearings are designed to operate at different operating speeds. Speed is specified as the maximum (a) rpm (b) metres/second (c) metres/minute (d) metres/hour
Last Answer : (b) metres/second
Description : The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned
Last Answer : (a) minimum expected life