The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

The maximum efficiency of a square threaded screw is

(A) (1 - sinφ)/ (1 + sinφ)

(B) (1 + sinφ)/ (1 - sinφ)s

(C) (1 - sinφ)/ (1 + cosφ)

(D) (1 + cosφ)/ (1 - sinφ)
by

1 Answer

Answer :

(A) (1 - sinφ)/ (1 + sinφ)
by

Related questions

Maximum efficiency of a square threaded is given by a) 1-sinǾ/1+sinǾ b) 1+sinǾ/1-sinǾ c) 1-2sinǾ/1+2sinǾ d) 1+2sinǾ/1-2sinǾ

Description : Maximum efficiency of a square threaded is given by a) 1-sinǾ/1+sinǾ b) 1+sinǾ/1-sinǾ c) 1-2sinǾ/1+2sinǾ d) 1+2sinǾ/1-2sinǾ

Last Answer : a) 1-sinǾ/1+sinǾ

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Last Answer : b. Set screws

Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Description : Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Last Answer : a) 50%

Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Last Answer : a) decreases

Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Description : Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Last Answer : b) False

Efficiency of screw depends upon lead of the screw. a) True b) False

Description : Efficiency of screw depends upon lead of the screw. a) True b) False

Last Answer : a) True

Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Last Answer : d. all of the above

The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Last Answer : (d) never be across the threaded portion

Which type of joints is better when the product is subjected to large vibrations: welded or threaded? a) Welded b) Threaded c) Both have same results d) Depends on the magnitude of the vibrational force

Description : Which type of joints is better when the product is subjected to large vibrations: welded or threaded? a) Welded b) Threaded c) Both have same results d) Depends on the magnitude of the vibrational force

Last Answer : a) Welded

Threaded joints are non-separable joints. a) True b) False

Description : Threaded joints are non-separable joints. a) True b) False

Last Answer : b) False

Which of the following fastening devices has its both ends threaded? (A) Bolt (B) Stud (C) Set screw (D) Split nut

Description : Which of the following fastening devices has its both ends threaded? (A) Bolt (B) Stud (C) Set screw (D) Split nut

Last Answer : (B) Stud

Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Description : Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Last Answer : b. 2/3 of the total threaded length showing

If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Description : If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Last Answer : a) Dog Point

Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Last Answer : b) False

Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Description : Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Last Answer : (C) Cap screw with hexagonal socket head

A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Description : A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Last Answer : (A) Major diameter

The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Description : The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Last Answer : (A) Major diameter

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Description : In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Last Answer : b) False

The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Description : The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Last Answer : a) Ellipse

The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Description : The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Last Answer : a) Ellipse

The region of safety in maximum shear stress theory contains which of the given shape a) Hexagon b) Rectangle c) Square d) None of the mentioned

Description : The region of safety in maximum shear stress theory contains which of the given shape a) Hexagon b) Rectangle c) Square d) None of the mentioned

Last Answer : a) Hexagon

If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse

Description : If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse

Last Answer : b) Square

Efficiency of a screw jack in maximum when its 31 helix angle, ? is a.45 + ?/2 b.107 dynes c.? d.45 - ?/2 e.45?

Description : Efficiency of a screw jack in maximum when its 31 helix angle, ? is a.45 + ?/2 b.107 dynes c.? d.45 - ?/2 e.45?

Last Answer : d. 45 - ?/2

If the potential is given by, V = 10sin θ cosφ/r, find the density at the point P(2, π/2, 0) (in 10 -12 units) a) 13.25 b) 22.13 c) 26.31 d) 31.52

Description : If the potential is given by, V = 10sin θ cosφ/r, find the density at the point P(2, π/2, 0) (in 10 -12 units) a) 13.25 b) 22.13 c) 26.31 d) 31.52

Last Answer : b) 22.13

Find the Laplace equation value of the following potential field V = ρ cosφ + z a) 0 b) 1 c) 2 d) 3

Description : Find the Laplace equation value of the following potential field V = ρ cosφ + z a) 0 b) 1 c) 2 d) 3

Last Answer : a) 0

Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Description : Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Last Answer : c. Greater

Term which is not applicable to a welded joint (i) Higher efficiency (ii)Easy process (iii) Faster process

Description : Term which is not applicable to a welded joint (i) Higher efficiency (ii)Easy process (iii) Faster process

Last Answer : (ii)Easy process

In a flywheel the safe stress is 25.2MN/m 2 and the density is 7 g/cm 3 . Then what is the maximum peripheral velocity ? 1. 30m/s 2. 45m/s 3. 60m/s 4. 120m/s

Description : In a flywheel the safe stress is 25.2MN/m 2 and the density is 7 g/cm 3 . Then what is the maximum peripheral velocity ? 1. 30m/s 2. 45m/s 3. 60m/s 4. 120m/s

Last Answer : 3. 60m/s

The rated life of a bearing varies (a) directly as load (b) inversely as the square of the load (c) inversely as the cube of the load

Description : The rated life of a bearing varies (a) directly as load (b) inversely as the square of the load (c) inversely as the cube of the load

Last Answer : (c) inversely as the cube of the load

The rated life of a bearing varies A. Directly as load B. Inversely as square of load C. Inversely as cube of load D. Inversely as fourth power of load

Description : The rated life of a bearing varies A. Directly as load B. Inversely as square of load C. Inversely as cube of load D. Inversely as fourth power of load

Last Answer : C. Inversely as cube of load

The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1

Description : The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1

Last Answer : (D) 1

The rated life of a bearing varies (A) Directly as load (B) Inversely as square of load (C) Inversely as cube of load (D) Inversely as fourth power of load

Description : The rated life of a bearing varies (A) Directly as load (B) Inversely as square of load (C) Inversely as cube of load (D) Inversely as fourth power of load

Last Answer : (C) Inversely as cube of load

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root

Description : The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root

Last Answer : b) No, it is directly proportional

Spring having square ends has 1 inactive coil. a) True b) False

Description : Spring having square ends has 1 inactive coil. a) True b) False

Last Answer : b) False

Plug weld is a. Rectangular b. Square c. Triangular d. None

Description : Plug weld is a. Rectangular b. Square c. Triangular d. None

Last Answer : d. None

Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Last Answer : c. Triangular

Lap welded joints are a. Rectangular b. Square c. Triangular d. None

Description : Lap welded joints are a. Rectangular b. Square c. Triangular d. None

Last Answer : c. Triangular

Which of the following requires more space for the rotation of spanner? a) Square Head b) Hexagonal Head c) Both require equal space of rotation d) Cannot be stated

Description : Which of the following requires more space for the rotation of spanner? a) Square Head b) Hexagonal Head c) Both require equal space of rotation d) Cannot be stated

Last Answer : a) Square Head

The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress

Description : The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress

Last Answer : (C) Twice of shear stress

The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d

Description : The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d

Last Answer : (C) 1.5d

Calculate the coefficient of fluctuation of speed if maximum speed is 2500rpm and minimum speed is 1800rpm. 1. 1.44 2. 1.33 3. 0.33 4. 0.44

Description : Calculate the coefficient of fluctuation of speed if maximum speed is 2500rpm and minimum speed is 1800rpm. 1. 1.44 2. 1.33 3. 0.33 4. 0.44

Last Answer : 3. 0.33

Reciprocal of coefficient of fluctuation of speed is called 1. fluctuation of energy 2. fluctuation of speed 3. maximum fluctuation of speed 4. coefficient of fluctuation of speed

Description : Reciprocal of coefficient of fluctuation of speed is called 1. fluctuation of energy 2. fluctuation of speed 3. maximum fluctuation of speed 4. coefficient of fluctuation of speed

Last Answer : 4. coefficient of fluctuation of speed

Maximum fluctuation of energy = 1. Max KE – Min KE 2. Max KE + Min KE 3. Max KE > Min KE 4. Max KE < Min KE

Description : Maximum fluctuation of energy = 1. Max KE – Min KE 2. Max KE + Min KE 3. Max KE > Min KE 4. Max KE < Min KE

Last Answer : 1. Max KE – Min KE

The coefficient of fluctuation of speed of flywheel is 1. ratio of maximum and minimum speeds during the cycle 2. ratio of maximum fluctuation of speed to the mean speed 3. ratio of mean speed to maximum fluctuation of speed during the cycle 4. sum of maximum fluctuation of speed and the mean speed

Description : The coefficient of fluctuation of speed of flywheel is 1. ratio of maximum and minimum speeds during the cycle 2. ratio of maximum fluctuation of speed to the mean speed 3. ratio of mean ... maximum fluctuation of speed during the cycle 4. sum of maximum fluctuation of speed and the mean speed

Last Answer : 2. ratio of maximum fluctuation of speed to the mean speed