Different types of bearings are designed to operate at different operating speeds. Speed is specified as the maximum (a) rpm (b) metres/second (c) metres/minute (d) metres/hour

Different types of bearings are designed to operate at different operating speeds.

Speed is specified as the maximum

(a) rpm

(b) metres/second

(c) metres/minute

(d) metres/hour
by

1 Answer

Answer :

(b) metres/second
by

Related questions

The coefficient of fluctuation of speed, when the maximum and minimum speeds are 300rpm and 290 rpm (A) 0.034 (B) 0.017 (C) 0.008 (D) 0/004

Description : The coefficient of fluctuation of speed, when the maximum and minimum speeds are 300rpm and 290 rpm (A) 0.034 (B) 0.017 (C) 0.008 (D) 0/004

Last Answer : (A) 0.034

Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr

Description : Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr

Last Answer : (b) 810 million rev

The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Last Answer : (d) all the mentioned

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Last Answer : (A) 500

The coefficient of fluctuation of speed of flywheel is 1. ratio of maximum and minimum speeds during the cycle 2. ratio of maximum fluctuation of speed to the mean speed 3. ratio of mean speed to maximum fluctuation of speed during the cycle 4. sum of maximum fluctuation of speed and the mean speed

Description : The coefficient of fluctuation of speed of flywheel is 1. ratio of maximum and minimum speeds during the cycle 2. ratio of maximum fluctuation of speed to the mean speed 3. ratio of mean ... maximum fluctuation of speed during the cycle 4. sum of maximum fluctuation of speed and the mean speed

Last Answer : 2. ratio of maximum fluctuation of speed to the mean speed

The difference the maximum and minimum speeds during a cycle is called (A) Fluctuation of speed (B) Maximum fluctuation of speed (C) Coefficient of fluctuation of speed (D) None of the above

Description : The difference the maximum and minimum speeds during a cycle is called (A) Fluctuation of speed (B) Maximum fluctuation of speed (C) Coefficient of fluctuation of speed (D) None of the above

Last Answer : (B) Maximum fluctuation of speed

The coefficient of fluctuation of speed of flywheel is, (A) Ratio of maximum and minimum speeds during the cycle (B) Ratio of maximum fluctuation of speed to the mean speed (C) Ratio of mean speed to maximum fluctuation of speed during the cycle (D) Sum of maximum fluctuation of speed and the mean speed

Description : The coefficient of fluctuation of speed of flywheel is, (A) Ratio of maximum and minimum speeds during the cycle (B) Ratio of maximum fluctuation of speed to the mean speed (C) Ratio of ... maximum fluctuation of speed during the cycle (D) Sum of maximum fluctuation of speed and the mean speed

Last Answer : (B) Ratio of maximum fluctuation of speed to the mean speed

The maximum fluctuation of speed of flywheel is, (A) Difference between maximum and minimum speeds during the cycle (B) Difference between maximum and mean speeds during the cycle (C) Difference between mean and minimum speeds during the cycle (D) Mean of maximum and minimum speeds during the cycle

Description : The maximum fluctuation of speed of flywheel is, (A) Difference between maximum and minimum speeds during the cycle (B) Difference between maximum and mean speeds during the cycle (C) Difference ... and minimum speeds during the cycle (D) Mean of maximum and minimum speeds during the cycle

Last Answer : (A) Difference between maximum and minimum speeds during the cycle

In an oil-lubricated journal bearing, coefficient of friction between the journal and the bearing. [IES-1995] (a) Remains constant at all speeds. (b) is minimum at zero speed and increases monotonically with increase in speed. (c) is maximum at zero speed and decreases monotonically with increase in speed. (d) becomes minimum at an optimum speed and then increases with further increase in speed.

Description : In an oil-lubricated journal bearing, coefficient of friction between the journal and the bearing. [IES-1995] (a) Remains constant at all speeds. (b) is minimum at zero speed and increases ... speed. (d) becomes minimum at an optimum speed and then increases with further increase in speed.

Last Answer : (d) becomes minimum at an optimum speed and then increases with further increase in speed.

A flywheel of moment of inertia 9.8kgm 2 fluctuates by 30 rpm for a fluctuation in energy of 1936 joules. The means speed of flywheel is (in rpm) 1. 600 2. 900 3. 968 4. 2940

Description : A flywheel of moment of inertia 9.8kgm 2 fluctuates by 30 rpm for a fluctuation in energy of 1936 joules. The means speed of flywheel is (in rpm) 1. 600 2. 900 3. 968 4. 2940

Last Answer : 1. 600

In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty

Description : In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty

Last Answer : b) Increase with increase in speed

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

In a journal bearings, the radius of the friction circle increases with the increase in- [IES-1997] (a) Load (b) Radius of the journal (c) Speed of the journal (d) Viscosity of the lubricant

Description : In a journal bearings, the radius of the friction circle increases with the increase in- [IES-1997] (a) Load (b) Radius of the journal (c) Speed of the journal (d) Viscosity of the lubricant

Last Answer : (b) Radius of the journal

Which one of the following types of bearings is employed in shafts of gearboxes of automobiles? [IES-1999] (a) Hydrodynamic journal bearings (b) Multi-lobed journal bearings (c) Antifriction bearings (d) Hybrid journal bearings

Description : Which one of the following types of bearings is employed in shafts of gearboxes of automobiles? [IES-1999] (a) Hydrodynamic journal bearings (b) Multi-lobed journal bearings (c) Antifriction bearings (d) Hybrid journal bearings

Last Answer : (c) Antifriction bearings

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

Certain types of radial bearings can also take thrust load. a) True b) False

Description : Certain types of radial bearings can also take thrust load. a) True b) False

Last Answer : a) True

Two trains 300 metres and 360 metres long are running in the same direction with speeds of 216 kmph and 162 kmph .In how much time will the first train cross the second? A) 54sec B) 44sec C) 40sec D) 14sec

Description : Two trains 300 metres and 360 metres long are running in the same direction with speeds of 216 kmph and 162 kmph .In how much time will the first train cross the second? A) 54sec B) 44sec C) 40sec D) 14sec 

Last Answer : ANSWE: B Explanation:  Length of the 1st train=300m  Length of the 2nd train=360m  Speed of the first train=216kmph  Speed of the second train=162kmph  Relative speed =(216-162)kmph  =54kmph. ...  =(660/15) sec  =44 sec  Therefore the first train cross the second at 44 sec.

A four-pole induction motor, operating on three-phase 60 cycle current will operate at approximately ___________. A. 850 RPM B. 1,150 RPM C. 1,750 RPM D. 3,550 RPM

Description : A four-pole induction motor, operating on three-phase 60 cycle current will operate at approximately ___________. A. 850 RPM B. 1,150 RPM C. 1,750 RPM D. 3,550 RPM

Last Answer : Answer: C

Runoff is measured in (A) Cubic metres (B) Cubic metres per sec. (C) Cubic metres per minute (D) Cubic metres per hour

Description : Runoff is measured in (A) Cubic metres (B) Cubic metres per sec. (C) Cubic metres per minute (D) Cubic metres per hour

Last Answer : Answer: Option B

Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Description : Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Last Answer : C 705

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Last Answer : (A) 0.5

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Last Answer : (A) 2

In a 2280 m race Dinesh beats Aarav by 360 m or 6 seconds. In another race on the same track at the same speeds. Aarav and karthick start at one end while Dinesh starts at the opposite end. How many metres would Aarav have covered ,by the time Dinesh meets karthick given that Dinesh speed is 16 m/sec more than that of karthick a) 1140 m b) 2280 m c) 2460 m d) 1180 m

Description : In a 2280 m race Dinesh beats Aarav by 360 m or 6 seconds. In another race on the same track at the same speeds. Aarav and karthick start at one end while Dinesh starts at the opposite end. How many metres would Aarav ... is 16 m/sec more than that of karthick a) 1140 m b) 2280 m c) 2460 m d) 1180 m

Last Answer : B Aarav 's speed =360/6 =60 m/s Time taken by Aarav to cover 2280 m =2280/60= 38 seconds Dinesh 's speed = 2280/60=38 m/s karthick 's speed = 22m/s Time taken by Dinesh to meet karthick in ... direction: Distance covered by Aarav: =2280/(38+22) =2280/60 =38 seconds =(38*60)m =2280 m

If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but governor will not operate (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Description : If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but ... (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Last Answer : (A) The governor will not operate but flywheel will be acting

If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Description : If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Last Answer : b) Governor

If L is the length of vehicles in metres, C is the clear distance between two consecutive vehicles (stopping sight distance), V is the speed of vehicles in km/hour, the maximum number N of vehicles/hour, is (A) N = 1000 V / (L + C) (B) N = (L + C) / 1000 V (C) N = 1000 L / (C + V) (D) N = 1000 C / (L + V)

Description : If L is the length of vehicles in metres, C is the clear distance between two consecutive vehicles (stopping sight distance), V is the speed of vehicles in km/hour, the maximum number N of vehicles/hour, is (A) N = 1000 V / (L + C ... ) / 1000 V (C) N = 1000 L / (C + V) (D) N = 1000 C / (L + V)

Last Answer : Answer: Option A

What is the safe maximum tripping speed of a turbine operating at 2500 rpm?

Description : What is the safe maximum tripping speed of a turbine operating at 2500 rpm?

Last Answer : The rule is to trip at 10 percent overspeed. Therefore, 2500 x 1.10 = 2750 rpm.

A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160

Description : A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160

Last Answer : 2. 790

The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm<5 (c) rotating at rpm<10 (d) rotating at rpm<15

Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm

Last Answer : (a) stationary

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Description : What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Last Answer : (c) Superior load carrying capacity at higher speeds

Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm<10 c) Rotating at rpm<5 d) None of the listed

Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm

Last Answer : a) Stationary

A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Description : A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Last Answer : (B) When the shafts are not in exact alignment

Ball bearings are, usually, made from (a) low carbon steel (b) high carbon steel (c) medium carbon steel (d) chrome steel

Description : Ball bearings are, usually, made from (a) low carbon steel (b) high carbon steel (c) medium carbon steel (d) chrome steel

Last Answer : (d) chrome steel

The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Last Answer : (b) 37.29 kN

The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False

Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False

Last Answer : (b) False

For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False

Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False

Last Answer : (a) True

The bearings of medium series have capacity __________ over the light series. (a) 10 to 20% (b) 20 to 30% (c) 30 to 40% (d) 40 to 50%

Description : The bearings of medium series have capacity __________ over the light series. (a) 10 to 20% (b) 20 to 30% (c) 30 to 40% (d) 40 to 50%

Last Answer : (c) 30 to 40%

The bearings of heavy series have capacity __________ over the medium series. (a) 10 to 20% (b) 20 to 30% (c) 30 to 40% (d) 40 to 50%

Description : The bearings of heavy series have capacity __________ over the medium series. (a) 10 to 20% (b) 20 to 30% (c) 30 to 40% (d) 40 to 50%

Last Answer : (b) 20 to 30%

Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Description : Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Last Answer : (d) None of the mentioned

The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Description : The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Last Answer : (a) needle roller bearings

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Description : The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Last Answer : (b) separable

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Last Answer : (c) Spherical roller thrust bearings and taper roller bearings

In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Description : In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Last Answer : (d) 25°