Description : Coarse threads have helix angle _____ fine threads. a) Equal to b) Greater than c) Lesser than d) There is no relation
Last Answer : c) Lesser than
Description : Which threads have greater resistance to unscrewing? a) Coarse b) Fine c) They have equal resistance d) Cannot be determined
Last Answer : b) Fine
Description : Which type of threads is recommended for fluctuating loads? a) Fine threads b) Coarse Threads c) Either of fine or coarse d) None of the listed
Last Answer : a) Fine threads
Description : The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch
Last Answer : (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Last Answer : (b) False
Description : The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False
Last Answer : b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Last Answer : (a) True
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Last Answer : a) True
Description : What is the approximate nominal diameter for coarse threads? a. d = 1.136 dc b. d = 1.59 dc c. d = 1.19 dc d. d = 0.5 dc
Last Answer : c. d = 1.19 dc
Description : Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d
Last Answer : (A) h = 0.4 d
Description : The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs
Last Answer : (D) Concentric springs
Description : Concentric springs are used, (A) To achieve greater load carrying capacity with given space (B) To achieve fail-safe system (C) To eliminate surge (D) Any of the above objectives
Last Answer : (D) Any of the above objectives
Description : Crests and roots of the threads may lead to leakage in fluid tight threads if flattened or rounded to a circular arc. a) True b) False
Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer
Last Answer : (B) Making shank diameter equal to core diameter of threads
Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing stress in shank (B) Increasing stress in core diameter of threads (C) Decreasing stress in shank (D) Decreasing stress in core diameter of threads
Last Answer : (A) Increasing stress in shank
Description : What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance
Last Answer : (c) Superior load carrying capacity at higher speeds
Description : Petroff’s equation is used to find out (A) Load carrying capacity of the bearing (B) Frictional losses in the bearing (C) Unit bearing pressure on the bearing (D) Pressure distribution around the periphery of the journal
Last Answer : (B) Frictional losses in the bearing
Description : Sommerfeld number is (A) Similar to bearing characteristic number (B) Similar to Reynold’s number (C) Dimensionless parameter that contains all the design parameters (D) Used to find out dynamic load carrying capacity of the hydrodynamic bearing
Last Answer : (C) Dimensionless parameter that contains all the design parameters
Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three
Last Answer : (D) All the three
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False
Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False
Description : When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing ... threads c. crushing stress induced is equal to permissible crushing stress d. all of the above
Last Answer : b. permissible crushing stress is more than crushing stress induced in the threads
Description : In trapezoidal threads, f (coefficient of friction) can be taken as a) f sec θ b) f cos θ c) f sin θ d) f cosec θ
Last Answer : a) f sec θ
Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above
Last Answer : d. all of the above
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply ... tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim
Description : For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply ... tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim
Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm
Last Answer : (a) stationary
Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm
Last Answer : a) Stationary
Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load
Last Answer : (d) completely reversed load
Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load
Last Answer : a) Ductile material under static load
Description : The capacity of welded structures to damp vibrations is quite good. a) True b) False
Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned
Last Answer : d) All of the mentioned
Description : The maximum bearing capacity of soil is that of (A) Black cotton soil (B) Loose fine sandy soil (C) Dry coarse sandy soil (D) Hard rocks
Last Answer : Answer: Option D
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Description : For majority of bearings, actual life is considerably greater than rated life. a) True b) False
Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False
Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are true and R is the correct explanation of A
Description : A radial bearing supports the load that acts along the axis of the shaft. a) True b) False
Description : Certain types of radial bearings can also take thrust load. a) True b) False
Description : The shock absorbing capacity of bolt can be increased by making the shank diameter ________ the root diameter. a) Lesser than b) Equal to c) Greater than d) No effect
Last Answer : b) Equal to
Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring
Last Answer : (d) concentric spring
Description : In the expression of dynamic load capacity P=XVF r + YF a , Y stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor
Last Answer : (c) Thrust load factor
Description : In the expression of dynamic load capacity P=XVF r + YF a , X stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor
Last Answer : (b) Radial load factor
Description : In the expression of dynamic load capacity P=XVF r + YF a , V stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor
Last Answer : (a) Race rotation factor