Description : The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch
Last Answer : (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch
Description : Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d
Last Answer : (A) h = 0.4 d
Description : Which type of threads is recommended for fluctuating loads? a) Fine threads b) Coarse Threads c) Either of fine or coarse d) None of the listed
Last Answer : a) Fine threads
Description : Which threads have greater resistance to unscrewing? a) Coarse b) Fine c) They have equal resistance d) Cannot be determined
Last Answer : b) Fine
Description : Coarse threads have helix angle _____ fine threads. a) Equal to b) Greater than c) Lesser than d) There is no relation
Last Answer : c) Lesser than
Description : The static load carrying capacity of fine threads is greater than that of coarse threads. a) True b) False
Last Answer : b) False
Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer
Last Answer : (B) Making shank diameter equal to core diameter of threads
Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing stress in shank (B) Increasing stress in core diameter of threads (C) Decreasing stress in shank (D) Decreasing stress in core diameter of threads
Last Answer : (A) Increasing stress in shank
Description : If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm
Last Answer : a) 17.27mm
Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False
Description : Nominal size of a pipe is an indication of its __________ diameter. (A) Inner (B) Outer (C) Approximate (D) None of these
Last Answer : (C) Approximate
Description : Crests and roots of the threads may lead to leakage in fluid tight threads if flattened or rounded to a circular arc. a) True b) False
Description : In trapezoidal threads, f (coefficient of friction) can be taken as a) f sec θ b) f cos θ c) f sin θ d) f cosec θ
Last Answer : a) f sec θ
Description : When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing ... threads c. crushing stress induced is equal to permissible crushing stress d. all of the above
Last Answer : b. permissible crushing stress is more than crushing stress induced in the threads
Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above
Last Answer : d. all of the above
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False
Description : The average daily wages of 450 workers in a factory is Rs.45/- and the average daily wages of 340 workers in another factory is Rs.60/-.What is the approximate average daily wages of workers from both the factories together? a) Rs.61 b) Rs.59 c) Rs.70 d) Rs.51 e) Rs.60
Last Answer : Total wages of a factory =450 x 45= Rs. 20250/ Total wages of another factory = 340 x 60 = Rs. 20400 Total average = 20250 + 20400/450 + 340 = 40650/790 = 51.46 = Rs. 51 Answer: d)
Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc
Last Answer : (A) h = 0.5 dc
Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc
Last Answer : (B) h = 0.25 dc
Description : The diameter of knuckle pin in the knuckle joint is usually... A. 0.5 d B. 0.8 d C. 1.5 d D. d
Last Answer : D. d
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Last Answer : (a) True
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Last Answer : a) True
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : A screw jack has 4 threads per inch. The mean radius of the thread is 2.338 inches. The mean diameter of the bearing surface under the cap is 3.25 inches. What is the turning moment required to raise the bload of 150 kg ( a.5.61 kg-inch b.50.6 kg-inch c.107 dynes d.30.3 kg-inch e.23.6 kg-inch
Last Answer : b. 50.6 kg-inch
Description : The expected discharge to be obtained from an open well sunk in coarse sand is 0.0059 cumec. If the working depression head of the well is 3 m, the minimum diameter of the well, is (A) 2 m (B) 2.25 m (C) 2.50 m (D) 3.00 m
Last Answer : (D) 3.00 m
Description : If the discharge of a sewer running half is 628 1.p.s., i = 0.001, and n = 0.010, the diameter of the sewer, is A. 1.39 m B. 1.49 m C. 1.59 m D. 1.69 m
Last Answer : ANS: D
Description : A sewer has a diameter of 300 mm and slop of 1 in 400. While running full it has a mean velocity of 0.7 m/s. If both the diameter and slope are doubled (to respectively be 600 mm and 1 in 200), what will be the changed mean velocity ... 's formula. (a) 1.59 m/s (b) 2.80 m/s (c) 0.90 m/s (d) 1.00 m/s
Last Answer : (a) 1.59 m/s
Description : What is the spectrum of stereophonic FM signal? A. 19 to 38 kHz B. 30 to 53 kHz C. 59.5 to 74.5 kHz D. 88 to 108 MHz
Last Answer : B. 30 to 53 kHz
Description : The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz
Last Answer : D. 30 to 53 kHz
Description : How do I calculate the relationship between linear travel and threads at a certain diameter?
Last Answer : answer:Look through this: http://en.wikipedia.org/wiki/Unified_Thread_Standard Basically the second number is threads per inch e.g. 10–32 is a #10 screw with 32 threads per inch. So 1 turn = 1 thread = 0.03125” screw travel.
Description : The minimum water content at which the soil just begins to crumble when rolled into threads 3 mm in diameter, is known (A) Liquid limit (B) Plastic limit (C) Shrinkage limit (D) Permeability limit
Last Answer : (B) Plastic limit
Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)
Last Answer : 4. 2(shaft diameter)
Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)
Last Answer : (D) 2 (shaft diameter)
Description : The needle rollers are a maximum of _______ millimeter in diameter. (a) 4 (b) 5 (c) 6 (d) 7
Last Answer : (b) 5
Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm
Last Answer : c) 6.1mm
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm
Last Answer : (a) 35 mm
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Last Answer : (b) False
Description : A sliding contact bearing is operating under stable condition. The pressure developed in oil film is p when the journal rotates at N rpm. The dynamic viscosity of lubricant is μ and effective coefficient of ... to p and f) (d) f is directly proportional to μ and inversely proportional to N
Last Answer : (b) f is directly proportional to μ and N
Description : The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1
Last Answer : (D) 1
Description : The length to diameter ratio for a short bearing is (A) More than 1 (B) Less than 1 (C) 8
Last Answer : (B) Less than 1
Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False
Description : The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above
Last Answer : (A) mean coil diameter / wire diameter
Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection
Last Answer : (C) Ratio of mean coil diameter to wire diameter