What are the applications of current sources?

What are the applications of current sources?
by

1 Answer

Answer :

Transistor current sources are widely used in analog ICs both as biasing elements and as load devices for amplifier stages.
by

Related questions

Justify the reasons for using current sources in integrated circuits.

Description : Justify the reasons for using current sources in integrated circuits.

Last Answer : (i) Superior insensitivity of circuit performance to power supply variations and temperature.  (ii) More economical than resistors in terms of die area required to provide bias currents of ... the high incremental resistance of current source results in high voltage gain at low supply voltages.

The main power sources for a satellite are A. batteries B. solar cells C. fuel cells D. thermoelectric generators 58. The maximum height of an ellip

Description : The main power sources for a satellite are A. batteries B. solar cells C. fuel cells D. thermoelectric generators 58. The maximum height of an ellip

Last Answer : B. solar cells

Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Description : Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Last Answer : D. All of these

Indicate the noise whose sources are in category different from that of the other three? A. Solar noise B. Cosmic noise C. Atmospheric noise D. Galactic noise

Description : Indicate the noise whose sources are in category different from that of the other three? A. Solar noise B. Cosmic noise C. Atmospheric noise D. Galactic noise

Last Answer : C. Atmospheric noise

Name one or more sources of noise bearing on electronic communications. A. Steam boiler B. Galaxies C. Internal combustion engine D. Both B and C

Description : Name one or more sources of noise bearing on electronic communications. A. Steam boiler B. Galaxies C. Internal combustion engine D. Both B and C

Last Answer : D. Both B and C

What happens when the common terminal of V+ and V- sources is not grounded?

Description : What happens when the common terminal of V+ and V- sources is not grounded?

Last Answer : If the common point of the two supplies is not grounded, twice the supply voltage will get applied and it may damage the op-amp

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line

List the applications of instrumentation amplifier.

Description : List the applications of instrumentation amplifier.

Last Answer : a. Temperature indicator b. Temperature controller c. Light intensity meters d. Water flow meter c. Thermal conductivity meter f. Analog weight scale

Write some applications of PN junction diode

Description : Write some applications of PN junction diode

Last Answer : 1. Rectifier circuit ii. clipping and clamping iii voltage multiplier iv AM detection v. Feedback diodes vi Freewheeling diode

List the applications of 555 timer in Astable mode of operation

Description : List the applications of 555 timer in Astable mode of operation

Last Answer : *FSK generator  *Pulse-position modulator

List the applications of 555 timer in monostable mode of operation

Description : List the applications of 555 timer in monostable mode of operation

Last Answer : *missing pulse detector *Linear ramp generator *Frequency divider *Pulse width modulation.

Mention some applications of 555 timer

Description : Mention some applications of 555 timer

Last Answer : *Oscillator *pulse generator *ramp and square wave generator *mono-shot multivibrator *burglar alarm *traffic light control.

Mention some typical applications of PLL

Description : Mention some typical applications of PLL

Last Answer : • Frequency multiplication/division • Frequency translation • AM detection • FM demodulation • FSK demodulation.

What are the applications of comparator?

Description : What are the applications of comparator?

Last Answer : 1.Zero crossing detector 2.Window detector 3.Time marker generator 4.Phase detector

List the applications of Log amplifiers:

Description : List the applications of Log amplifiers:

Last Answer : 1.Analog computation may require functions such as lnx, log x, sin hx etc. These functions can be performed by log amplifiers 2.Log amplifier can perform direct dB display on digital voltmeter and spectrum analyzer 3.Log amplifier can be used to compress the dynamic range of a signal

Write down the applications of precision diode.

Description : Write down the applications of precision diode. 

Last Answer : 1.Half - wave rectifier 2.Full - Wave rectifier 3.Peak – value detector 4.Clipper 5.Clamper

What are the applications of V-I converter?

Description : What are the applications of V-I converter?

Last Answer : 1.Low voltage dc and ac voltmeter 2.L E D 3.Zener diode tester

Mention some of the non – linear applications of op-amps

Description : Mention some of the non – linear applications of op-amps

Last Answer : Rectifier, peak detector, clipper, clamper, sample and hold circuit, log amplifier, anti –log amplifier, multiplier are some of the non – linear op-amp circuits. 

Mention some of the linear applications of op – amps.

Description : Mention some of the linear applications of op – amps.

Last Answer : Adder, subtractor, voltage –to- current converter, current –to- voltage converters, instrumentation amplifier, analog computation ,power amplifier, etc are some of the linear opamp circuits.

Why IC 741 is not used for high frequency applications?

Description : Why IC 741 is not used for high frequency applications?

Last Answer : IC741 has a low slew rate because of the predominance of capacitance present in the circuit at higher frequencies. As frequency increases the output gets distorted due to limited slew rate. 

Why open loop OP-AMP configurations are not used in linear applications?

Description : Why open loop OP-AMP configurations are not used in linear applications?

Last Answer : The open loop gain of the op-amp is not a constant and it varies with changing the temperature and variations in power supply.Also the bandwidth of the open loop op-amp is negligibly small.For this reasons open loop OP-AMP configurations are not used in linear applications.

Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end

Description : Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end

Last Answer : A. At the ends

If the antenna current is doubled, the field strength at a particular position is A. doubled B. halved C. multiplied by a factor of four D. divided by a factor of four

Description : If the antenna current is doubled, the field strength at a particular position is A. doubled B. halved C. multiplied by a factor of four D. divided by a factor of four

Last Answer : A. doubled

A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Description : A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Last Answer : C. has a zero DC resistance to ground

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

The current maximum in a Marconi antenna is found at A. the base of the antenna B. the center of the antenna C. some point between the base and the center of the antenna D. the top of the antenna

Description : The current maximum in a Marconi antenna is found at A. the base of the antenna B. the center of the antenna C. some point between the base and the center of the antenna D. the top of the antenna

Last Answer : A. the base of the antenna

If the radiated power increase 10.89 times, the antenna current increases by ______. A. 3.3 times B. 6.6 times C. 1.82 times D. 10.89 times

Description : If the radiated power increase 10.89 times, the antenna current increases by ______. A. 3.3 times B. 6.6 times C. 1.82 times D. 10.89 times

Last Answer : A. 3.3 times

A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Description : A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Last Answer : A. Antenna

If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Description : If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Last Answer : B. critical phased array

_________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Description : _________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Last Answer : B. LNA

Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Description : Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Last Answer : B. narrowing the bandwidth

Power is __________. A. actual amount of power reference to 1mW B. logarithmic ratio of two powers C. definite amount of energy per time period D. current flow per time period

Description : Power is __________. A. actual amount of power reference to 1mW B. logarithmic ratio of two powers C. definite amount of energy per time period D. current flow per time period

Last Answer : C. definite amount of energy per time period

The antenna current is doubled when the modulation index is doubled in ______ AM system. A. A5C B. A3J C. A3 D. A3H

Description : The antenna current is doubled when the modulation index is doubled in ______ AM system. A. A5C B. A3J C. A3 D. A3H

Last Answer : B. A3J

Which of the following best describes a dip-meter? A. An SWR meter B. A counter C. A variable LC oscillator with metered feedback current D. A field strength meter

Description : Which of the following best describes a dip-meter? A. An SWR meter B. A counter C. A variable LC oscillator with metered feedback current D. A field strength meter

Last Answer : C. A variable LC oscillator with metered feedback current

The bending of radio waves passing over the top of a mountain range that disperses a weak portion of the signal behind the mountain is A. eddy-current phase effect B. knife-edge diffraction C. shadowing D. mirror refraction effect

Description : The bending of radio waves passing over the top of a mountain range that disperses a weak portion of the signal behind the mountain is A. eddy-current phase effect B. knife-edge diffraction C. shadowing D. mirror refraction effect

Last Answer : B. knife-edge diffraction

A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Description : A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Last Answer : A. 0.1

What is the current frequency band given most attenuation for satellite communications? A. Ku B. C band C. J D. P

Description : What is the current frequency band given most attenuation for satellite communications? A. Ku B. C band C. J D. P

Last Answer : A. Ku

What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Description : What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Last Answer : D. Photovoltaic effect

An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Description : An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Last Answer : C. Crossfire

At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Description : At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Last Answer : D. Maximum voltage and minimum current.

Best described a dip-meter. A. A variable LC oscillator with metered feedback current B. An SWR meter C. A counter D. A field strength meter

Description : Best described a dip-meter. A. A variable LC oscillator with metered feedback current B. An SWR meter C. A counter D. A field strength meter

Last Answer : A. A variable LC oscillator with metered feedback current

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

Halo is also called A. Flare B. Dark current C. Glitch D. Ghost

Description : Halo is also called A. Flare B. Dark current C. Glitch D. Ghost

Last Answer : A. Flare

relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Feedhorn B. Satellite dish C. Satellite receiver D. LNB

Description : _______ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Feedhorn B. Satellite dish C. Satellite receiver D. LNB

Last Answer : D. LNB

How much does the radiated power of an antenna increases if its current increased by 3.3 times? A. 6.6 times B. 3.3 times C. 10.89 times D. 9.9 times

Description : How much does the radiated power of an antenna increases if its current increased by 3.3 times? A. 6.6 times B. 3.3 times C. 10.89 times D. 9.9 times

Last Answer : C. 10.89 times

If the modulation index of an AM wave is doubled, the antenna current is also doubled, the AM system being used is A. A5C B. A3J C. A3H D. A3

Description : If the modulation index of an AM wave is doubled, the antenna current is also doubled, the AM system being used is A. A5C B. A3J C. A3H D. A3

Last Answer : B. A3J

Define input bias current?

Description : Define input bias current?

Last Answer : It is defined as the average of the currents entering into the input terminals of an op-amp.

Define input offset current?

Description : Define input offset current?

Last Answer : It is defined as the algebraic difference between the current entering the inverting and non-inverting terminal of an op-amp.

What is reverse saturation current?

Description : What is reverse saturation current?

Last Answer : The current due to the minority carriers is called the reverse saturation current.

Define current amplification factor?

Description : Define current amplification factor?

Last Answer : It is defined as the ratio of change in output current to the change in input current at constant other side voltage.