What happens when the common terminal of V+ and V- sources is not grounded?

What happens when the common terminal of V+ and V- sources is not grounded?
by

1 Answer

Answer :

If the common point of the two supplies is not grounded, twice the supply voltage will get applied and it may damage the op-amp
by

Related questions

The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are operated by the same relay coil B. screw connections are on terminal board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Description : The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are ... board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Last Answer : Answer: B

Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Description : Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Last Answer : C. Dipole

The antenna efficiency of an HF grounded vertical antenna can be made comparable to that of a half-wave antenna A. By installing a good ground radial system B. By isolating the coax shield from ground C. By shortening the vertical D. By lengthening the vertical

Description : The antenna efficiency of an HF grounded vertical antenna can be made comparable to that of a half-wave antenna A. By installing a good ground radial system B. By isolating the coax shield from ground C. By shortening the vertical D. By lengthening the vertical

Last Answer : A. By installing a good ground radial system

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

How can the antenna efficiency of an HF grounded vertical antenna be made comparable to that of a half-wave antenna? A. By lengthening the vertical B. By installing a good ground radial system C. By shortening the vertical D. By isolating the coax shield from ground

Description : How can the antenna efficiency of an HF grounded vertical antenna be made comparable to that of a half-wave antenna? A. By lengthening the vertical B. By installing a good ground radial system C. By shortening the vertical D. By isolating the coax shield from ground

Last Answer : B. By installing a good ground radial system

The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Description : The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Last Answer : B. Input and output

What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Description : What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Last Answer : D. 75 Ω

When a transmission line uses ground return, it is called a/an __________ line. A. ungrounded B. balanced C. unbalanced D. grounded

Description : When a transmission line uses ground return, it is called a/an __________ line. A. ungrounded B. balanced C. unbalanced D. grounded

Last Answer : C. unbalanced

One input terminal of high gain comparator circuit is grounded and a ...

Description : One input terminal of high gain comparator circuit is grounded and a sinusoidal voltage is applied to the other input. The output of comparator will be___________.

Last Answer : One input terminal of high gain comparator circuit is grounded and a sinusoidal voltage is applied to the other input. The output of comparator will be a square wave.

The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Description : The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Last Answer : B. 300 Ω

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Description : What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Last Answer : A. 300 ohms

Which of the following is not referred to as data terminal equipment? A. Telephone set B. Printers C. Modem D. Computer

Description : Which of the following is not referred to as data terminal equipment? A. Telephone set B. Printers C. Modem D. Computer

Last Answer : C. Modem

Refers to a continuous tone generated in a local exchange terminal through a combination of two frequencies 350 Hz, and 440 Hz. A. Busy tone B. Call waiting tone C. Dial tone D. Standard tone

Description : Refers to a continuous tone generated in a local exchange terminal through a combination of two frequencies 350 Hz, and 440 Hz. A. Busy tone B. Call waiting tone C. Dial tone D. Standard tone

Last Answer : B. Call waiting tone

These are used to connect non-ISDN equipment ot ISDN line. A. Digipeaters B. Terminal adapters C. Local repeaters D. Terminal repeaters

Description : These are used to connect non-ISDN equipment ot ISDN line. A. Digipeaters B. Terminal adapters C. Local repeaters D. Terminal repeaters

Last Answer : B. Terminal adapters

A microwave link between the earth station and the down-town terminal. A. STL B. Uplink C. Downlink D. Terrestrial link

Description : A microwave link between the earth station and the down-town terminal. A. STL B. Uplink C. Downlink D. Terrestrial link

Last Answer : D. Terrestrial link

Modem is referred to as ______. A. Universal asynchronous Rx/Tx B. Data communication equipment C. Universal synchronous Rx/Tx D. Data terminal equipment

Description : Modem is referred to as ______. A. Universal asynchronous Rx/Tx B. Data communication equipment C. Universal synchronous Rx/Tx D. Data terminal equipment

Last Answer : B. Data communication equipment

The primary purpose of the data modem is to A. interface analog terminal equipment to analog communications channel B. interface digital terminal equipment to analog communications channel C. interface analog terminal equipment to digital communications channel D. interface digital terminal equipment to digital communications channel

Description : The primary purpose of the data modem is to A. interface analog terminal equipment to analog communications channel B. interface digital terminal equipment to analog communications ... to digital communications channel D. interface digital terminal equipment to digital communications channel

Last Answer : B. interface digital terminal equipment to analog communications channel

The line control unit (LCU) operates on the data digital form. A. Data communications equipment (DCE) B. UART C. Modem D. Data terminal equipment (DTE)

Description : The line control unit (LCU) operates on the data digital form. A. Data communications equipment (DCE) B. UART C. Modem D. Data terminal equipment (DTE)

Last Answer : D. Data terminal equipment (DTE)

___________ is a device in data transmission to interface data terminal equipment to an analogue transmission line. A. RS 232 B. Connector C. Modem D. RJ-11 plug

Description : ___________ is a device in data transmission to interface data terminal equipment to an analogue transmission line. A. RS 232 B. Connector C. Modem D. RJ-11 plug

Last Answer : C. Modem

Transmission lines are either balanced or unbalanced with respect to _________. A. negative terminal B. input C. ground D. positive terminal

Description : Transmission lines are either balanced or unbalanced with respect to _________. A. negative terminal B. input C. ground D. positive terminal

Last Answer : C. ground

What is the purpose of having input and output capacitors in three terminal IC regulators?

Description : What is the purpose of having input and output capacitors in three terminal IC regulators?

Last Answer : A capacitor connected between the input terminal and ground cancels the inductive effects due to long distribution leads. The output capacitor improves the transient response.

The main power sources for a satellite are A. batteries B. solar cells C. fuel cells D. thermoelectric generators 58. The maximum height of an ellip

Description : The main power sources for a satellite are A. batteries B. solar cells C. fuel cells D. thermoelectric generators 58. The maximum height of an ellip

Last Answer : B. solar cells

Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Description : Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Last Answer : D. All of these

Indicate the noise whose sources are in category different from that of the other three? A. Solar noise B. Cosmic noise C. Atmospheric noise D. Galactic noise

Description : Indicate the noise whose sources are in category different from that of the other three? A. Solar noise B. Cosmic noise C. Atmospheric noise D. Galactic noise

Last Answer : C. Atmospheric noise

Name one or more sources of noise bearing on electronic communications. A. Steam boiler B. Galaxies C. Internal combustion engine D. Both B and C

Description : Name one or more sources of noise bearing on electronic communications. A. Steam boiler B. Galaxies C. Internal combustion engine D. Both B and C

Last Answer : D. Both B and C

Justify the reasons for using current sources in integrated circuits.

Description : Justify the reasons for using current sources in integrated circuits.

Last Answer : (i) Superior insensitivity of circuit performance to power supply variations and temperature.  (ii) More economical than resistors in terms of die area required to provide bias currents of ... the high incremental resistance of current source results in high voltage gain at low supply voltages.

What are the applications of current sources?

Description : What are the applications of current sources?

Last Answer : Transistor current sources are widely used in analog ICs both as biasing elements and as load devices for amplifier stages.

Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Last Answer : Answer: B

To neglect a current source, the terminal across the sources are:

Description : To neglect a current source, the terminal across the sources are:  (1) Open circuited (2) Short-circuited (3) Replaced by some resistance (4) Replaced by capacitance

Last Answer : To neglect a current source, the terminal across the sources are: Open circuited.

According to Coast Guard Regulations (46 CFR), the talking and calling circuits of a sound powered telephone system must be _____________. A. intrinsically safe B. independent of each other C. independently grounded D. connected to a common ground

Description : According to Coast Guard Regulations (46 CFR), the talking and calling circuits of a sound powered telephone system must be _____________. A. intrinsically safe B. independent of each other C. independently grounded D. connected to a common ground

Last Answer : Answer: B

Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common talking circuit is composed of two ungrounded wires. C. The ringing circuit has two grounded wires connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Description : Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common ... connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Last Answer : Answer: B

And ITU-T specification code that deals with the telephone circuits. A. X series B. T series C. V series D. I series

Description : And ITU-T specification code that deals with the telephone circuits. A. X series B. T series C. V series D. I series

Last Answer : C. V series

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

Which of the following described the very early standard that defines binary digits as space/mark line condition and voltage levels? A. V.4 B. V.2 C. V.1 D. V.5

Description : Which of the following described the very early standard that defines binary digits as space/mark line condition and voltage levels? A. V.4 B. V.2 C. V.1 D. V.5

Last Answer : C. V.1

RS-232, RS-449, RS-530, V, 24 and X.21 are examples of ____________. A. standards for interfaces between modems and transmission facilities B. standards for various types of transmission channels C. standards for interfaces between terminals and modems D. standards for end to end performance of data communications system

Description : RS-232, RS-449, RS-530, V, 24 and X.21 are examples of ____________. A. standards for interfaces between modems and transmission facilities B. standards for various types of ... for interfaces between terminals and modems D. standards for end to end performance of data communications system

Last Answer : C. standards for interfaces between terminals and modems

What are the applications of V-I converter?

Description : What are the applications of V-I converter?

Last Answer : 1.Low voltage dc and ac voltmeter 2.L E D 3.Zener diode tester

What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Description : What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Last Answer : A. It is increased

What happens to the beamwidth of an antenna as the gain is increased? A. The beamwidth increases geometrically as the gain is increased. B. The beamwidth increases arithmetically as the gain is increased. C. The beamwidth is essentially unaffected by the gain of the antenna. D. The beamwidth decreases as the gain is increased.

Description : What happens to the beamwidth of an antenna as the gain is increased? A. The beamwidth increases geometrically as the gain is increased. B. The beamwidth increases arithmetically as the gain is increased ... unaffected by the gain of the antenna. D. The beamwidth decreases as the gain is increased.

Last Answer : D. The beamwidth decreases as the gain is increased.

In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Description : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Last Answer : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

A three-phase synchronous motor has a terminal voltage of 460 V and a terminal current of 120 A at a power factor of 0.95 lagging, synchronous reactance of 1.68 ohm and the field current is 47 A. The field to armature mutual inductance of the synchronous motor is _____________.

Description : A three-phase synchronous motor has a terminal voltage of 460 V and a terminal current of 120 A at a power factor of 0.95 lagging, synchronous reactance of 1.68 ohm and the field current is 47 A. The field to armature mutual ... _____________.      (a). 20mH   (b). 16mH   (c). 24mH   (d). 22mH

Last Answer : 22

What are the sources of 240 V AC class I supply? What are the functions of each part of UPS?

Description : What are the sources of 240 V AC class I supply? What are the functions of each part of UPS? 

Last Answer : Six sources. Three 20 kVA UPS for safety related loads. Two 60 kVA UPS for non-safety related loads. One 60 kVA UPS as a standby to safety related loads. These all UPS are back up by ... UPS into service. Manual bypass To take main UPS to maintenance by putting stand by UPS into service. 

Which of the following is not a common type of fiber-optic cable? a. Single-mode step-index b. Multimode graded-index c. Single-mode graded-index d. Multimode step-index

Description : Which of the following is not a common type of fiber-optic cable? a. Single-mode step-index b. Multimode graded-index c. Single-mode graded-index d. Multimode step-index

Last Answer : c. Single-mode graded-index

Which of the following is not a common application of fiber-optic cable? a. Computer networks b. Long-distance telephone systems c. Closed circuit TV d. Consumer TV

Description : Which of the following is not a common application of fiber-optic cable? a. Computer networks b. Long-distance telephone systems c. Closed circuit TV d. Consumer TV

Last Answer : d. Consumer TV

Which of the following is the most common application of satellite? A. Surveillance B. Military application C. Communications D. Newscasting

Description : Which of the following is the most common application of satellite? A. Surveillance B. Military application C. Communications D. Newscasting

Last Answer : C. Communications

What is the common up-converter and down-converter IF? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Description : What is the common up-converter and down-converter IF? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Last Answer : C. 70 MHz

The most common device used as an LNA is A. zener diode B. tunnel diode C. IMPATT D. Shockley diode

Description : The most common device used as an LNA is A. zener diode B. tunnel diode C. IMPATT D. Shockley diode

Last Answer : B. tunnel diode

What is known as the alignment of the three color guns to a common point? A. Confetti B. Divergence C. Convergence D. Synchronization

Description : What is known as the alignment of the three color guns to a common point? A. Confetti B. Divergence C. Convergence D. Synchronization

Last Answer : C. Convergence

What is the common up-converter and down-converter IF for microwave communications? A. 60 MHz B. 80 MHz C. 120 MHz D. 70 MHz

Description : What is the common up-converter and down-converter IF for microwave communications? A. 60 MHz B. 80 MHz C. 120 MHz D. 70 MHz

Last Answer : D. 70 MHz