What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

What kind of effect is referred to a varying light producing a varying voltage output of a
detector?
A. Current effect
B. Voltage effect
C. Resistive effect
D. Photovoltaic effect
by

1 Answer

Answer :

D. Photovoltaic effect
by

Related questions

Which of the following is NOT a common light detector ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Photodiode ∙ d. Avalanche photodiode

Description : Which of the following is NOT a common light detector ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Photodiode ∙ d. Avalanche photodiode

Last Answer : ∙ b. Photovoltaic diode

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

A sensor which changes light intensity into electric voltage. (a) LDR (b) thermistor (c) photodiode (d) photovoltaic

Description : A sensor which changes light intensity into electric voltage. (a) LDR (b) thermistor (c) photodiode (d) photovoltaic

Last Answer : (a) LDR

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Description : The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Last Answer : C. APDs

The following statement(s) is/are true concerning initial microbiologic diagnostic techniques. a. Appropriate expeditious transport of specimens to the microbiology laboratory is essential for obtaining accurate clinical information b. The use of potassium hydroxide in preparing a specimen slide for light microscopy will be useful in identification of anaerobic bacteria c. Antibiotic sensitivity is determined by exposing the specific microorganism to varying amounts of antibiotic with the concentration of the antibiotic inhibiting growth referred to as the MIC (minimal inhibitory concentration) d. Serum levels of antimicrobial agents should achieve in excess of a 4-to 8-fold increase over the MIC to be considered clinically efficacious.

Description : The following statement(s) is/are true concerning initial microbiologic diagnostic techniques. a. Appropriate expeditious transport of specimens to the microbiology laboratory is essential for obtaining accurate ... a 4-to 8-fold increase over the MIC to be considered clinically efficacious.

Last Answer : Answer: a, c, d Because most surgical infections are polymicrobial, specimens should be cultured for aerobic and anaerobic bacteria, as well as fungi. Although aerobic and aerotolerant ... fold increase over MIC during the peak serum level have been demonstrated to be clinically efficacious

The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode output current to the input optical power ∙ C. the ratio of the input power to output power ∙ D. the ratio of output current to input current

Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current

Last Answer : the ratio of the diode output current to the input optical power

What kind of energy is converted into light energy as a result of the action of light on a photovoltaic cell ?

Description : What kind of energy is converted into light energy as a result of the action of light on a photovoltaic cell ?

Last Answer : Answer : The action of light on a photovoltaic cell results in the conversion of light energy into electrical energy.

The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Description : The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Last Answer : Answer: C

In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying

Description : In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying

Last Answer : In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying T, keeping ton constant

In dc choppers for chopping period T, the output voltage can be controlled by FM by varying

Description : In dc choppers for chopping period T, the output voltage can be controlled by FM by varying   (A) T keeping Ton constant (B) Ton keeping T constant (C) Toff keeping T constant (D) None of the above

Last Answer : In dc choppers for chopping period T, the output voltage can be controlled by FM by varying T keeping Ton constant

Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Description : Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Last Answer : Answer: B

Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Description : A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Last Answer : A. Constant peak amplitude

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Solar cells work on the principle of – (1) photovoltaic effect (2) photoelectric effect (3) photoconductive effect (4) photosynthesis

Description : Solar cells work on the principle of – (1) photovoltaic effect (2) photoelectric effect (3) photoconductive effect (4) photosynthesis

Last Answer : (1) photovoltaic effect Explanation: Solar cells work on the principle of photovoltaic effect.

Solar cells work on the principle of (1) photovoltaic effect (2) photoelectric effect (3) photoconductive effect (4) photosynthesis

Description : Solar cells work on the principle of (1) photovoltaic effect (2) photoelectric effect (3) photoconductive effect (4) photosynthesis

Last Answer : photovoltaic effect

What is a device that detects both vertically and horizontally polarized signals simultaneously? A. Orthomode transducer B. Crystal detector C. Optoisolator D. Isomode detector

Description : What is a device that detects both vertically and horizontally polarized signals simultaneously? A. Orthomode transducer B. Crystal detector C. Optoisolator D. Isomode detector

Last Answer : A. Orthomode transducer

A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Description : A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Last Answer : D. Limiter

What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Description : What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Last Answer : C. Video detector

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Description : A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Last Answer : A. Noise equivalent power

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Description : If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Last Answer : A. 14 ns

Combination of modulator, channel and detector. A. Transceiver B. Discrete channel C. T/R channel D. Transponder

Description : Combination of modulator, channel and detector. A. Transceiver B. Discrete channel C. T/R channel D. Transponder

Last Answer : B. Discrete channel

Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Description : Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Last Answer : D. detector stage

What are the problems associated with switch type phase detector?

Description : What are the problems associated with switch type phase detector?

Last Answer : 1.The output voltage Ve is proportional to the input signal amplitude.This is undesirable because it makes phase detector gain and loop gain dependent on the input signal amplitude. 2.The output is proportional to cosQ making it non linear.

What is a switch type phase detector?

Description : What is a switch type phase detector?

Last Answer : An electronic switch is opened and closed by signal coming from VCO and the input signal is chopped at a repetition rate determined by the VCO frequency.This type of phase detector is called a ... detector since the phase information for only one half of the input signal is detected and averaged.

Give the classification of phase detector:

Description : Give the classification of phase detector:

Last Answer : 1.Analog phase detector . 2.Digital phase detector

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Last Answer : B. Phase control

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Many living organisms exhibit the unique property of producing visible light. The compound that is oxidized with subsequent light emission is usually referred to as luciferin. What is the enzyme which catalyzes the reaction known as?

Description : Many living organisms exhibit the unique property of producing visible light. The compound that is oxidized with subsequent light emission is usually referred to as luciferin. What is the enzyme which catalyzes the reaction known as?

Last Answer : ANSWER: Luciferase

The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the collector of 'Q1' C. acts as a low capacitive reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Description : The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the ... reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Last Answer : Answer: D

Pick out the wrong statement. (A) The X-rays cannot be deflected by electric field unlike cathode rays (B) The intensity of X-rays can be measured by ionisation current produced due to the ionisation of gas by X-rays (C) The quality of X-rays can be controlled by varying the anode-cathode voltage (D) Crystal structure of a material can be studied by an electron microscope

Description : Pick out the wrong statement. (A) The X-rays cannot be deflected by electric field unlike cathode rays (B) The intensity of X-rays can be measured by ionisation current produced due to the ... the anode-cathode voltage (D) Crystal structure of a material can be studied by an electron microscope

Last Answer : (C) The quality of X-rays can be controlled by varying the anode-cathode voltage

The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Last Answer : B. light sensitivity

The minimum optical power a light detector can receive and still produce a usable electrical output signal.

Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal.

Last Answer : light sensitivity

Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Description : Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Last Answer : Avalanche photodiode

Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Description : Which of the following is the fastest light sensor? ∙ A. PIN photodiode ∙ B. Photovoltaic diode ∙ C. Photodiode ∙ D. Avalanche photodiode

Last Answer : D. Avalanche photodiode

Which of the following is the fastest light sensor ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Phototransistor ∙ d. Avalanche photodiode

Description : Which of the following is the fastest light sensor ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Phototransistor ∙ d. Avalanche photodiode

Last Answer : ∙ d. Avalanche photodiode

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

Effect of varying light intensity on photosynthesis. -Biology

Description : Effect of varying light intensity on photosynthesis. -Biology

Last Answer : answer:

Effect of varying light intensity on photosynthesis. -Biology

Description : Effect of varying light intensity on photosynthesis. -Biology

Last Answer : answer:

The variation in output voltage as the load changes is referred to as what? How is it expressed?

Description : The variation in output voltage as the load changes is referred to as what? How is it expressed?

Last Answer : Voltage regulation. As a percentage.