Why IC 741 is not used for high frequency applications?

Why IC 741 is not used for high frequency applications?
by

1 Answer

Answer :

IC741 has a low slew rate because of the predominance of capacitance present in the circuit at higher frequencies. As frequency increases the output gets distorted due to limited slew rate. 
by

Related questions

Draw pin diagram of Op-Amp IC-741.

Description : Draw pin diagram of Op-Amp IC-741.

Last Answer : Pin diagram of Op-Amp IC-741 :

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the

Description : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

Last Answer : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the internal compensation

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line

What is an opto-coupler IC?

Description : What is an opto-coupler IC?

Last Answer : Opto-coupler IC is a combined package of a photo-emitting device and a photosensing device.Examples for opto-coupler circuit : LED and a photo diode, LED and photo transistor, LED and Darlington. Examples for opto-coupler IC : MCT 2F , MCT 2E .

What is the purpose of having input and output capacitors in three terminal IC regulators?

Description : What is the purpose of having input and output capacitors in three terminal IC regulators?

Last Answer : A capacitor connected between the input terminal and ground cancels the inductive effects due to long distribution leads. The output capacitor improves the transient response.

Give some examples of monolithic IC voltage regulators

Description : Give some examples of monolithic IC voltage regulators

Last Answer : 78XX series fixed output, positive voltage regulators 79XX series fixed output, negative voltage regulators 723 general purpose regulator.

What are the advantages of IC voltage regulators?

Description : What are the advantages of IC voltage regulators?

Last Answer : *low cost *high reliability *reduction in size *excellent performance

What is a compander IC? Give some examples.

Description : What is a compander IC? Give some examples.

Last Answer : The term companding means compressing and expanding.In a communication system, the audio signal is compressed in the transmitter and expanded in the receiver. Examples : LM 2704- LM 2707 ; NE 570/571.

What is the use of buried n+ layer in monolithic IC transistor?

Description : What is the use of buried n+ layer in monolithic IC transistor?

Last Answer : The buried n+ layer provides a low resistance path in the active collector region for the flow of current

How many times does 82 go into 741?

Description : How many times does 82 go into 741?

Last Answer : 9 times with a remainder of 3

Are 450 and 741 relatively prime?

Description : Are 450 and 741 relatively prime?

Last Answer : No, because 1 is not their only common factor.

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

In an examination it is required to get 672 aggregate marks to pass. A student gets 70% marks and is declared failed by 126 marks. What are the maximum aggregate marks a student can get? a) 780 b) 840 c) 741 d) 805 e) 983

Description : In an examination it is required to get 672 aggregate marks to pass. A student gets 70% marks and is declared failed by 126 marks. What are the maximum aggregate marks a student can get? a) 780 b) 840 c) 741 d) 805 e) 983

Last Answer : Answer: A Difference = 672-126 = 546 According to the question, 70% of total aggregate = 546 Total aggregate marks = 546 × 100 /70  = 54600/70  = 780

List the applications of instrumentation amplifier.

Description : List the applications of instrumentation amplifier.

Last Answer : a. Temperature indicator b. Temperature controller c. Light intensity meters d. Water flow meter c. Thermal conductivity meter f. Analog weight scale

Write some applications of PN junction diode

Description : Write some applications of PN junction diode

Last Answer : 1. Rectifier circuit ii. clipping and clamping iii voltage multiplier iv AM detection v. Feedback diodes vi Freewheeling diode

List the applications of 555 timer in Astable mode of operation

Description : List the applications of 555 timer in Astable mode of operation

Last Answer : *FSK generator  *Pulse-position modulator

List the applications of 555 timer in monostable mode of operation

Description : List the applications of 555 timer in monostable mode of operation

Last Answer : *missing pulse detector *Linear ramp generator *Frequency divider *Pulse width modulation.

Mention some applications of 555 timer

Description : Mention some applications of 555 timer

Last Answer : *Oscillator *pulse generator *ramp and square wave generator *mono-shot multivibrator *burglar alarm *traffic light control.

Mention some typical applications of PLL

Description : Mention some typical applications of PLL

Last Answer : • Frequency multiplication/division • Frequency translation • AM detection • FM demodulation • FSK demodulation.

What are the applications of comparator?

Description : What are the applications of comparator?

Last Answer : 1.Zero crossing detector 2.Window detector 3.Time marker generator 4.Phase detector

List the applications of Log amplifiers:

Description : List the applications of Log amplifiers:

Last Answer : 1.Analog computation may require functions such as lnx, log x, sin hx etc. These functions can be performed by log amplifiers 2.Log amplifier can perform direct dB display on digital voltmeter and spectrum analyzer 3.Log amplifier can be used to compress the dynamic range of a signal

Write down the applications of precision diode.

Description : Write down the applications of precision diode. 

Last Answer : 1.Half - wave rectifier 2.Full - Wave rectifier 3.Peak – value detector 4.Clipper 5.Clamper

What are the applications of V-I converter?

Description : What are the applications of V-I converter?

Last Answer : 1.Low voltage dc and ac voltmeter 2.L E D 3.Zener diode tester

Mention some of the non – linear applications of op-amps

Description : Mention some of the non – linear applications of op-amps

Last Answer : Rectifier, peak detector, clipper, clamper, sample and hold circuit, log amplifier, anti –log amplifier, multiplier are some of the non – linear op-amp circuits. 

Mention some of the linear applications of op – amps.

Description : Mention some of the linear applications of op – amps.

Last Answer : Adder, subtractor, voltage –to- current converter, current –to- voltage converters, instrumentation amplifier, analog computation ,power amplifier, etc are some of the linear opamp circuits.

What are the applications of current sources?

Description : What are the applications of current sources?

Last Answer : Transistor current sources are widely used in analog ICs both as biasing elements and as load devices for amplifier stages.

Why open loop OP-AMP configurations are not used in linear applications?

Description : Why open loop OP-AMP configurations are not used in linear applications?

Last Answer : The open loop gain of the op-amp is not a constant and it varies with changing the temperature and variations in power supply.Also the bandwidth of the open loop op-amp is negligibly small.For this reasons open loop OP-AMP configurations are not used in linear applications.

A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Description : A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Last Answer : A. Antenna

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

A porous material is far more efficient at high than low frequency absorption. How to improve sound absorption at lower frequencies using this absorber? A. Increase the thickness B. Decrease the thickness C. Mount with and airspace behind D. Both A and C above

Description : A porous material is far more efficient at high than low frequency absorption. How to improve sound absorption at lower frequencies using this absorber? A. Increase the thickness B. Decrease the thickness C. Mount with and airspace behind D. Both A and C above

Last Answer : D. Both A and C above

What is the frequency range of an aircraft’s Very High Frequency (VHF) communications? A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz) B. 108.000 MHz to 117.95 MHz C. 329.15 MHz to 335.00 MHz D. 2.0000 MHz to 29.999 MHz

Description : What is the frequency range of an aircraft’s Very High Frequency (VHF) communications? A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz) B. 108.000 MHz to 117.95 MHz C. 329.15 MHz to 335.00 MHz D. 2.0000 MHz to 29.999 MHz

Last Answer : A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz)

What is the high frequency sound that cannot be heard by the human ear? A. Ultrasonic B. Transonic C. Subsonic D. Supersonic

Description : What is the high frequency sound that cannot be heard by the human ear? A. Ultrasonic B. Transonic C. Subsonic D. Supersonic

Last Answer : A. Ultrasonic

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

Determine from the following radio frequency that falls under the very high frequency band of the radio spectrum. A. 345.00 MHz B. 144.50 MHz C. 235.50 MHz D. 450.00 MHz

Description : Determine from the following radio frequency that falls under the very high frequency band of the radio spectrum. A. 345.00 MHz B. 144.50 MHz C. 235.50 MHz D. 450.00 MHz

Last Answer : C. 235.50 MHz

The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Description : The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Last Answer : B. 30 to 300 GHz

In radio High frequency communications the higher the radio frequency the ______. A. Higher it can reach B. Shorter it can reach C. Effect is null D. Longer it can reach

Description : In radio High frequency communications the higher the radio frequency the ______. A. Higher it can reach B. Shorter it can reach C. Effect is null D. Longer it can reach

Last Answer : D. Longer it can reach

A radio frequency in the ultra high frequency band of the radio spectrum band. A. 235.50 MHz B. 450.50 MHz C. 150.50 GHz D. 0.31250 GHz

Description : A radio frequency in the ultra high frequency band of the radio spectrum band. A. 235.50 MHz B. 450.50 MHz C. 150.50 GHz D. 0.31250 GHz

Last Answer : D. 0.31250 GHz

Which of the following fall under the high frequency band of the radio spectrum? A. 8.2345 MHz B. 150.50 MHz C. 2.4555 MHz D. 35.535 MHz

Description : Which of the following fall under the high frequency band of the radio spectrum? A. 8.2345 MHz B. 150.50 MHz C. 2.4555 MHz D. 35.535 MHz

Last Answer : A. 8.2345 MHz

Designates the sensation of low or high in the sense of the base and treble. A. Frequency B. Intensity C. Pitch D. SPL

Description : Designates the sensation of low or high in the sense of the base and treble. A. Frequency B. Intensity C. Pitch D. SPL

Last Answer : C. Pitch

In practical op-amps, what is the effect of high frequency on its performance?

Description : In practical op-amps, what is the effect of high frequency on its performance?

Last Answer : The open-loop gain of op-amp decreases at higher frequencies due to the presence of parasitic capacitance. The closed-loop gain increases at higher frequencies and leads to instability.

The laser frequency when the light has the wavelength 800 nm is a. 375 x 10^12 Hz b. 475 x 10^15 Hz c. 375 x 10^9 Hz d. 375 x 10^18 Hz

Description : The laser frequency when the light has the wavelength 800 nm is a. 375 x 10^12 Hz b. 475 x 10^15 Hz c. 375 x 10^9 Hz d. 375 x 10^18 Hz

Last Answer : a. 375 x 10^12 Hz

What is the photon energy for an infrared wave with frequency of 1012 Hz? a. 10.6 x 1034 joules b. 6.63 x 10-34 joules c. 6.63 x 10-22 joules d. 10.6 x 1022 joules

Description : What is the photon energy for an infrared wave with frequency of 1012 Hz? a. 10.6 x 1034 joules b. 6.63 x 10-34 joules c. 6.63 x 10-22 joules d. 10.6 x 1022 joules

Last Answer : c. 6.63 x 10-22 joules

When a beam of light enters one medium from another, which quantity will not change? a. Direction b. Speed c. Frequency d. Wavelength

Description : When a beam of light enters one medium from another, which quantity will not change? a. Direction b. Speed c. Frequency d. Wavelength

Last Answer : c. Frequency

What generates a light beam of a specific visible frequency? a. Laser b. Maser c. Infrared d. Flashlight

Description : What generates a light beam of a specific visible frequency? a. Laser b. Maser c. Infrared d. Flashlight

Last Answer : a. Laser

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases