The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

The ability of a material to resist plastic deformation known as _____________

a) Tensile strength

b) Yield strength

c) Modulus of elasticity

d) Impact strength
by

1 Answer

Answer :

b) Yield strength
by

Related questions

The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation

Description : The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation

Last Answer : b) Plasticity

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The Modulus of Elasticity for a material refers to: w) the ability of a material to resist corrosion x) the ratio of stress over strain y) the maximum load over the cross sectional area z) none of the above

Description : The Modulus of Elasticity for a material refers to: w) the ability of a material to resist corrosion x) the ratio of stress over strain y) the maximum load over the cross sectional area z) none of the above

Last Answer : ANSWER: X -- THE RATIO OF STRESS OVER STRAIN

What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Description : What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Last Answer : ANSWER: Y -- YIELD STRENGTH

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Last Answer : d) All of the mentioned

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Description : The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Last Answer : B. Percent elongation

Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal of load c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Last Answer : a) Ability of material to absorb energy when deformed elastically

The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

…. is the property of a material which enables it to resist plastic deformation.

Description : …. is the property of a material which enables it to resist plastic deformation.

Last Answer : …. is the property of a material which enables it to resist plastic deformation. (A) elasticity (B) plasticity (C) hardness (D) ductility

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Description : Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Last Answer : a) Modulus of elasticity

Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) The damping capacity of a material is due to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Description : Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) ... to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Last Answer : Option B

Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is proportional to the age of the member at the time of loading. (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Last Answer : d) All of the listed

There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Last Answer : b) False

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Last Answer : b. Soderberg line

In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (a)Firstly Ultimate >yield > elastic limit

In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (c) Thirdly Ultimate=yield=elastic limit

Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Description : Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Last Answer : (B) Toughness

The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress

Description : The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress

Last Answer : (c) fluctuating stress

If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse

Description : If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse

Last Answer : b) Square

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Last Answer : Option A

Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain

Description : Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain

Last Answer : d. Normal stress on each face of cube / Volumetric strain

Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain

Description : Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain

Last Answer : a)Tensile stress / Tensile strain

When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Description : When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Last Answer : d) Plasticity

An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Description : An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Last Answer : (A) Sewage sludge

Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Description : Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Last Answer : (D) All of the above

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (B) h = 0.25 dc

The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (d) shear strength

he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (a) tensile strength

Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Last Answer : c) Creep

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Description : Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Last Answer : b) No, it is done up to plastic stage

The ability of a material to be formed by hammering or rolling is known as _________ a) Malleability b) Ductility c) Harness d) Brittleness

Description : The ability of a material to be formed by hammering or rolling is known as _________ a) Malleability b) Ductility c) Harness d) Brittleness

Last Answer : a) Malleability

A material is able to retain the deformation permanently by virtue of its (A) Elasticity (B) Plasticity (C) Ductility (D) Malleability

Description : A material is able to retain the deformation permanently by virtue of its (A) Elasticity (B) Plasticity (C) Ductility (D) Malleability

Last Answer : (B) Plasticity

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Last Answer : (D) Thermal co-efficient of expansion

The relation between modulus of rupture fcr, splitting strength fcs and direct tensile strength fcl is given by (A) fcr - fcs = fcl (B) fcr > fcs > fcl (C) fcr < fcs < fcl (D) fcs > fcr > fcl

Description : The relation between modulus of rupture fcr, splitting strength fcs and direct tensile strength fcl is given by (A) fcr - fcs = fcl (B) fcr > fcs > fcl (C) fcr < fcs < fcl (D) fcs > fcr > fcl

Last Answer : Option B

Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Description : Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Last Answer : Answer: Option A