Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)
Last Answer : (D) 2 (shaft diameter)
Description : For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply ... tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim
Description : For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply ... tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim
Description : In vehicle flywheel is place between 1. clutch and propeller shaft 2. engine and clutch 3. before engine 4. propeller shaft and differential
Last Answer : 2. engine and clutch
Description : In vehicles, flywheel is placed in between (A) Engine and clutch (B) Clutch and Propeller shaft (C) Propeller shaft and Differential (D) Before engine
Last Answer : (A) Engine and clutch
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False
Last Answer : b) False
Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed
Last Answer : b) Radial
Description : In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above
Last Answer : (C) The keyway is cut in both the shaft and the hub
Description : Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub
Last Answer : (D) There is relative motion between shaft and hub
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Last Answer : a) True
Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm
Last Answer : d) 53mm
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm
Last Answer : c) 6.1mm
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm
Last Answer : a) 100mm
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : The shaft is always stepped with ________ diameter at the middle portion and __________ diameter at the shaft ends. a) Minimum, maximum b) Maximum, minimum c) Minimum, minimum d) Zero, infinity
Last Answer : b) Maximum, minimum
Description : The angle of twist for a transmission shaft is inversely proportional to (A) Shaft diameter (B) (Shaft diameter)2 (C) (Shaft diameter)3 (D) (Shaft diameter)4
Last Answer : (D) (Shaft diameter)4
Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B
Last Answer : (C) Eight times that of B
Description : The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d
Last Answer : (C) 1.5d
Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component
Last Answer : (C) Key is the weakest component
Description : A flywheel of moment of inertia 9.8kgm 2 fluctuates by 30 rpm for a fluctuation in energy of 1936 joules. The means speed of flywheel is (in rpm) 1. 600 2. 900 3. 968 4. 2940
Last Answer : 1. 600
Description : Flywheel absorbs energy during those periods of crank rotation when 1. The twisting moment is greater than the resisting moment 2. The twisting moment is equal to the resisting moment 3. The twisting moment is less than resisting moment 4. The load on engine falls
Last Answer : 1. The twisting moment is greater than the resisting moment
Description : In a flywheel the safe stress is 25.2MN/m 2 and the density is 7 g/cm 3 . Then what is the maximum peripheral velocity ? 1. 30m/s 2. 45m/s 3. 60m/s 4. 120m/s
Last Answer : 3. 60m/s
Description : When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined
Last Answer : 1. Accelerated
Description : The coefficient of fluctuation of speed of Flywheel is given by 1. (N1-N2)/N 2. (N1+N2)/N 3. (N1-N2) x N
Last Answer : 1. (N1-N2)/N
Description : The radius of Gyration (k) for Rim Type Flywheel having radius ‘r’ is given by 1. k = 2r 2. k = r/2 3. k = r 4. k = r/3
Last Answer : 3. k = r
Description : Which of the following is used to control the speed variations of the engine caused by the fluctuations of the engine turning moment? 1. D-slide valve 2. Governor 3. Flywheel 4. Meyer’s expansion valve
Last Answer : 3. Flywheel
Description : A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160
Last Answer : 2. 790
Description : A flywheel connected to a punching machine has to supply energy of 400 Nm while running at a mean angular speed of 20 rad/s. If the total fluctuation of speed is not exceed to in kgm 2 is 1. 25 2. 50 3. 100 4. 125
Last Answer : 1. 25
Description : Split flywheel is made to 1. avoid cooling stress 2. reduce weight 3. increase weight 4. maximize large centrifugal force
Last Answer : 1. avoid cooling stress
Description : The flywheel is accelerate when 1. driving torque > load torque 2. driving torque < load torque 3. driving torque = load torque 4. driving torque / load torque
Last Answer : 1. driving torque > load torque
Description : Energy stored in flywheel in the form of 1. heat energy 2. kinetic energy 3. solar energy 4. thermal energy
Last Answer : 2. kinetic energy
Description : The coefficient of fluctuation of speed of flywheel is 1. ratio of maximum and minimum speeds during the cycle 2. ratio of maximum fluctuation of speed to the mean speed 3. ratio of mean ... maximum fluctuation of speed during the cycle 4. sum of maximum fluctuation of speed and the mean speed
Last Answer : 2. ratio of maximum fluctuation of speed to the mean speed
Description : The coefficient of fluctuation of energy of flywheel is 1. ratio of maximum fluctuation of energy to work done per cycle 2. ratio of to work done per cycle to maximum fluctuation of energy ... minimum kinetic energy during the cycle 4. ratio of maximum and minimum kinetic energy during the cycle
Last Answer : 1. ratio of maximum fluctuation of energy to work done per cycle
Description : The cross section of flywheel arm is 1. I section 2. Rectangular 3. Elliptical 4. Circular
Last Answer : 3. Elliptical