Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm
Last Answer : a) 100mm
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No
Last Answer : b) No
Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm
Last Answer : d) 53mm
Description : Entire torque is transmitted by friction in the clamp coupling. a) True b) False
Last Answer : b) False
Description : Clamp coupling employ bolts. a) True b) False
Last Answer : a) True
Description : In case of clamp coupling, power is transmitted by means of, (A) Friction force (B) Shear resistance (C) Crushing resistance (D) None of the above
Last Answer : (A) Friction force
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm
Last Answer : (a) 40mm
Description : The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm
Last Answer : (c) 50mm
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : Label size of foreign article is min & postage paid words should not be less than a) 70mm X 100mm & 300sq mm b) 50mm X 80mm & 200sq mm c) 25mm X 50 mm & 100 sq mm d) None of these
Last Answer : a) 70mm X 100mm & 300sq mm
Description : For high degree of workability, the slump value should vary between (a) 0 to 25mm (b) 25 to 50mm (c) 50 to 80mm (d) 80 to 100mm
Last Answer : (d) 80 to 100mm
Description : Muff coupling is designed as a ......... A. Thick cylinder B. Thin cylinder C. Solid shaft D. Hollow shaft
Last Answer : D. Hollow shaft
Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component
Last Answer : (C) Key is the weakest component
Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed
Last Answer : b) 1102.8N
Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed
Last Answer : c) 5.07mm
Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned
Last Answer : b) 40/9
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr
Last Answer : (b) 810 million rev
Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)
Last Answer : 4. 2(shaft diameter)
Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)
Last Answer : (D) 2 (shaft diameter)
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm
Last Answer : c) 6.1mm
Description : The shaft is always stepped with ________ diameter at the middle portion and __________ diameter at the shaft ends. a) Minimum, maximum b) Maximum, minimum c) Minimum, minimum d) Zero, infinity
Last Answer : b) Maximum, minimum
Description : The angle of twist for a transmission shaft is inversely proportional to (A) Shaft diameter (B) (Shaft diameter)2 (C) (Shaft diameter)3 (D) (Shaft diameter)4
Last Answer : (D) (Shaft diameter)4
Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B
Last Answer : (C) Eight times that of B
Description : The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d
Last Answer : (C) 1.5d
Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm
Last Answer : (a) 35 mm
Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links
Last Answer : D. Between the two lower Links
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined
Last Answer : (b) 4674.1N
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm
Last Answer : b) 24.9mm
Description : The split - pin is used in... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Last Answer : B. Knuckle joint
Description : The joints between link of a suspension bridge, which of the following joints used.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Description : To joining the links of a bicycle chain which of the following joint is used. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Description : Forked - pin joints is also called as... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Description : The valve rod connected in steam engine by using.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint