Op-amp can provide maximum output current of A. 25 mA B. 30 mA C. 35 mA D. 40 mA

Op-amp can provide maximum output current of

A. 25 mAB. 30 mA

C. 35 mA

D. 40 mA
by

1 Answer

Answer :

 25 mA
by

Related questions

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Output current from an LED is A. 20 mA B. 30 mA C. 40 mA D. 50 mA

Description : Output current from an LED is A. 20 mA B. 30 mA C. 40 mA D. 50 mA

Last Answer : 20 mA

Coil of relay is connected to the A. input of op-amp B. output of op-amp C. midpoint of op-amD. anywhere in between input and ouput of op-amp

Description : Coil of relay is connected to the A. input of op-amp B. output of op-amp C. midpoint of op-am D. anywhere in between input and ouput of op-amp

Last Answer : output of op-amp

Number of power supplies required to get output of op-amp is A. two B. four C. six D. three

Description : Number of power supplies required to get output of op-amp is A. two B. four C. six D. three

Last Answer : two

Output resistance of an actual op-amp is A. 45Ω B. 46Ω C. 70Ω D. 75Ω

Description : Output resistance of an actual op-amp is A. 45Ω B. 46Ω C. 70Ω D. 75Ω

Last Answer : 75Ω

Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Description : Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Last Answer : Answer :

Why the input resistance of an ideal OPAMP is infinite and output resistance is zero? secondly, how can we measure these resistances(input and output) in case of an ideal OPAMPand Real OP-AMP in the following conditions when 1- load is not connected. 2- load is connected.

Description : Why the input resistance of an ideal OPAMP is infinite and output resistance is zero? secondly, how can we measure these resistances(input and output) in case of an ideal OPAMPand Real OP-AMP in the following conditions when 1- load is not connected. 2- load is connected.

Last Answer : Ans- Ideal OP-AMP is a power ful concept. If one goes through the history of amplifying devices it becomes clear that less it loads the previous stage better the output signal. ie ... . Can refer application notes by device manufacturer available in internet for more precise and practical solutions.

Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Description : Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Last Answer : Summing Amplifier Circuit In this simple summing amplifier circuit, the output voltage, ( Vout ) now becomes proportional to the sum of the input voltages, V1, V2, V3, etc. Then we can ... to the non-inverting input of the op-amp, it will produce the positive sum of the input voltages.

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier ...

Description : What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

Last Answer : i don know

Actual op-amp may have an open loop gain of A. 102 B. 105 C. 103 D. 104

Description : Actual op-amp may have an open loop gain of A. 102 B. 105 C. 103 D. 104

Last Answer : 105

As long as op-amp is not saturated, the potential difference between inverting and non-inverting inputs is A. zero B. infinite C. 1 D. 2

Description : As long as op-amp is not saturated, the potential difference between inverting and non-inverting inputs is A. zero B. infinite C. 1 D. 2

Last Answer : zero

A device used to avoid the relay destroying the op-amp is A. diode B. LED C. reverse bias diode D. forward biased diode

Description :  A device used to avoid the relay destroying the op-amp is A. diode B. LED C. reverse bias diode D. forward biased diode

Last Answer : reverse bias diode

Impedance of ideal op-amp is A. zero B. 1 C. infinite D. 2

Description : Impedance of ideal op-amp is A. zero B. 1 C. infinite D. 2

Last Answer :  infinite

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave ...

Description : An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

Last Answer : Slew rate = 2πfv where v is the amplitude V=(1/2π*0.1) = 1.592V

Define input offset current. State the reasons for the offset currents at the input of the op-amp.

Description : Define input offset current. State the reasons for the offset currents at the input of the op-amp.

Last Answer : The difference between the bias currents at the input terminals of the op-amp is called as input offset current. The input terminals conduct a small value of dc current to bias the input transistors.Since the input transistors cannot be made identical,there exists a difference in bias currents.

The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Description : The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Last Answer : Answer: Option C

The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Description : The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Last Answer : (c) 35

To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Last Answer : Answer: D

When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A) and (+10 A) jacks B. 10 MA/ 10 AMP with leads in the (-COMMON) and (+) jacks C. 10 MA/ 10 AMP with leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

Current gain of a transistor which has collector current of 10 mA and a base current of 40 micro Ampere is: (a) 25 (b) 250 (c) 2500 (d) 25000

Description : Current gain of a transistor which has collector current of 10 mA and a base current of 40 micro Ampere is: (a) 25 (b) 250 (c) 2500 (d) 25000

Last Answer : b) 250

What is Op -Amp ?

Description : What is Op -Amp ?

Last Answer : The operational amplifier is abbreviated as OP-Amp . This OP-Amp is a high gain direct coupled negative feedback amplifier circuit with multiple transistors. Op-Amp is a modular , multistage amplifying device with a ... of op-amp is 500 ml. Op-amp IC : A709, LM108, LM208, CA741 and CA741T.

What is op amp?

Description : What is op amp?

Last Answer : An operational amplifier, which is often called an op-amp, is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output.[1] An op-amp ... at the input terminals (ideally infinite) and low output impedance at the output terminal(s) (idea

What is op amp?

Description : What is op amp?

Last Answer : An operational amplifier, which is often called an op-amp, is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output.[1] An op-amp ... at the input terminals (ideally infinite) and low output impedance at the output terminal(s) (idea

What is the type of feedback used in an op-amp Schmitt trigger?

Description : What is the type of feedback used in an op-amp Schmitt trigger?

Last Answer : The type of feedback used in an op-amp Schmitt trigger is positive feedback.

What is the basic building block of an op-amp?

Description : What is the basic building block of an op-amp?

Last Answer : The basic building block of an op-amp is differential amplifier.

What is the type of feedback employed in the inverting op-amp amplifier?

Description : What is the type of feedback employed in the inverting op-amp amplifier?

Last Answer : Negative feedback is employed in the inverting op-amp amplifier.

What are the DC characteristics of an op-amp?

Description : What are the DC characteristics of an op-amp?

Last Answer : a. input bias current b. Input offset current c .Input offset voltage d. Thermal drift

What are the AC characteristics of an op-amp?

Description : What are the AC characteristics of an op-amp?

Last Answer : a. Frequency response b. Slew rate

What is compensated op-amp?

Description : What is compensated op-amp?

Last Answer : Op-amp, which uses a capacitor internally for compensation, is called a compensated op-amp. This op-amp has a high gain stability and low bandwidth.

What is an op-amp?

Description : What is an op-amp?

Last Answer : The operational amplifier is a multi-terminal device, which is quite complex internally. An operational amplifier is a direct coupled high gain amplifier usually consisting of one or more ... as well as ac input signals and was originally designed for computing such mathematical functions.

Write transfer function of op amp as an integer.

Description : Write transfer function of op amp as an integer.

Last Answer : The transfer function of the integer is  LAL=1/MR1cf

What are the areas of application of non-linear op- amp circuits?

Description : What are the areas of application of non-linear op- amp circuits?

Last Answer : 1. Industrial instrumentation 2. Communication 3. Signal processing

Define CMRR of an op-amp.

Description : Define CMRR of an op-amp.

Last Answer : The relative sensitivity of an op-amp to a difference signal as compared to a common – mode signal is called the common –mode rejection ratio. It is expressed in decibels. CMRR= Ad/Ac

Define virtual ground of a OP-Amp?

Description : Define virtual ground of a OP-Amp? 

Last Answer : A virtual ground is a ground which acts like a ground. It is a point that is at the fixed ground potential (0v),though it is not practically connected to the actual ground or common terminal of the circuit.

Why open loop OP-AMP configurations are not used in linear applications?

Description : Why open loop OP-AMP configurations are not used in linear applications?

Last Answer : The open loop gain of the op-amp is not a constant and it varies with changing the temperature and variations in power supply.Also the bandwidth of the open loop op-amp is negligibly small.For this reasons open loop OP-AMP configurations are not used in linear applications.

what is meant by virtual ground in the op amp ?

Description : what is meant by virtual ground in the op amp ?

Last Answer : Ans-The op amp connected in a negative feedback configuration that is the o/p connected to the inverting terminal tried to produce the same voltage at the inverting node as we applied to ... the inverting node at the ground potential and whatever the difference between these two nodes are amplified.

Why the input impedance of OP-Amp is so high?

Description : Why the input impedance of OP-Amp is so high?

Last Answer : Ans-In OPAMP we have 4 stages 1st stage i.e the input stage is a dual i/p balanced o/p opamp whose i/p resistance is v high. and if we use FET in case of BJT for 1st stage diffamp then i/p resistance will be v high in M ohms.

Why the shape of OP-AMP is triangular not other shape?

Description : Why the shape of OP-AMP is triangular not other shape?

Last Answer : Ans-The Triangular shape symbolizes that it works for continous signals and hence forth it is an analog device. ex: Opamp If it is square then it is digital device. ex: Multiplexer If the shape is both triangular and square then it is mixed signal device. ex: ADC DAC

Why are the 2 input terminals of an op-amp are called as inverting & non-inverting terminals?

Description : Why are the 2 input terminals of an op-amp are called as inverting & non-inverting terminals?

Last Answer : Ans-Because if we give input to one input means that will produce the same phase output where as the other(Inverting) pin produce 180 degree phase shifted output.

what is meant by virtual ground in the op amp ?

Description : what is meant by virtual ground in the op amp ?

Last Answer : Ans-Ideally the output of op-amp should be zero. So for this to happen the 2 inputs must be same. Hence one of the input is considered to be low or at ground potential. But this input is not actually ground hence it is called as virtual ground.

Basic Op Amp Circuits

Description : Basic Op Amp Circuits

Last Answer : In this chapter we will be examining some common uses of op amps. Where Chapter Three focused on the theory of negative feedback in a more abstract way, this chapter zeroes in on the practical ... on using op amps with a single polarity power supply and how to increase the available output current.

Draw pin diagram of Op-Amp IC-741.

Description : Draw pin diagram of Op-Amp IC-741.

Last Answer : Pin diagram of Op-Amp IC-741 :

Explain the function of sample and hold circuit by using op-amp.

Description : Explain the function of sample and hold circuit by using op-amp.

Last Answer : sample and hold circuit by using op-amp The n-channel MOSFET is driven by a control voltage VC acts as a switch. The control voltage VC is applied to the gate of the MOSFET ... called sample period. The time period during which the voltage across capacitor is constant is called Hold period.

Describe the concept of virtual ground with reference to op-Amp.

Description : Describe the concept of virtual ground with reference to op-Amp.

Last Answer : Virtual ground concept:-In circuit point A is virtual ground. Figure shows inverting amplifier using op-amp. In this circuit non-inverting terminal is connected to the actual ground. Due to ... zero potential without actually grounding is known as virtual ground concept. Circuit diagram: 

Block Diagram of op-Amp

Description : Block Diagram of op-Amp

Last Answer : Block Diagram: The OP-AMP is basically a different amplifier i.e. it will amplify the voltage which is differentially present between its input terminals.  1.Input stage: The ... normally a complementary output stage. It increases the OPAMP. It also provides a low output resistance. 

Define the following terms related to Op-Amp: i) CMRR ii) SVRR

Description : Define the following terms related to Op-Amp: i) CMRR ii) SVRR

Last Answer : Definition:- i) SVRR: It is defined as the ratio of change of input offset voltage to the change in one supply voltage while keeping other supply voltage constant. Ideally,SVRR=0  ii)CMMR:-The ... gain should exceed common-mode gain, this will be a positive number, and the higher the better.

State any two characteristics of an ideal Op-amp.

Description : State any two characteristics of an ideal Op-amp.

Last Answer : Characteristics of Op-amp: i) Input offset voltage ii) Input offset current iii) Input bias current iv) Differential input resistance v) Input capacitance vi) CMRR-common mode rejection ration vii) ... voltage rejection ratio(SVRR) viii) Output resistance ix) Voltage gain x) Bandwidth xi) Slew rate

Draw and explain the Op-amp based subtractor

Description : Draw and explain the Op-amp based subtractor

Last Answer : Working The subtractor circuit is a basic op-amp circuit whose output voltage is the difference between two input voltages.  In the above circuit, the two input voltages are V1 and V2.  The op amp is used ... When differential gain is 1, ie Rf = R,  the output voltage is Vo = (V2 - V1).

Draw the diagram of zero crossing detector using op-amp and explain its working.

Description : Draw the diagram of zero crossing detector using op-amp and explain its working.

Last Answer : The zero crossing detector circuit is an important application of the op-amp comparator circuit. It can also be called as the sine to square wave converter. Anyone of the inverting or non-inverting ... the possibility of any false zero crossing due to noise voltages at the op-amp input.

An Op-amp as a voltage follower has a voltage gain of

Description : An Op-amp as a voltage follower has a voltage gain of

Last Answer : An Op-amp as a voltage follower has a voltage gain of Unity