Draw the following and write application of each. i. Well type manometer ii. Bellows.

 Draw the following and write application of each. i. Well type manometer ii. Bellows.
by

1 Answer

Answer :

1. Well type manometer

image

Application : Manometers are used in flow, pressure and force measurement systems.

 

2. Bellows 

image

Applications : i. These are used in the large indicating gauges, recorders where space is not a problem. ii. It is useful in pneumatic controllers.

by

Related questions

Draw venture meter and write steps to measure flow rate.

Description : Draw venture meter and write steps to measure flow rate.

Last Answer : Venturi meter consists of three sections that is converging section, throat section and diverging section. The flow is introduced to the meter through the inlet with diameter D' . The inclined angle ... to 15o . Flow rate is proportional to the square root of the differential pressure.

State humidity and draw hair type hygrometer.

Description : State humidity and draw hair type hygrometer.

Last Answer : Humidity is defined as it is a measure of water vapors present in the surrounding air.

Compare Bellows and diaphragm w.r.to construction, sensitivity, working principle and application.

Description : Compare Bellows and diaphragm w.r.to construction, sensitivity, working principle and application.

Last Answer : Sr. No Points Bellows diaphragm 1 construction 2 sensitivity Less sensitive as compared to diaphragm  More sensitive as compared to diaphragm ... as well as for vacuum, compound and differential pressure applications. II. For corrosive gases and liquids

Draw labeled dead weight tester.

Description : Draw labeled dead weight tester.

Last Answer : dead weight tester

Draw and describe constructional diagram of RVDT.

Description : Draw and describe constructional diagram of RVDT.

Last Answer : Rotary Variable Differential Transformer (RVDT) is inductive transducer, which converts the angular displacement into electrical signal. Construction and working : Figure shows the circuit diagram of ... - Vs1 Thus by using RVDT one can determine the angular displacement and its direction

Draw neat labeled diagram of optical pyrometer.

Description : Draw neat labeled diagram of optical pyrometer.

Last Answer :  optical pyrometer

Draw and describe construction and working of Bourdon tube.

Description : Draw and describe construction and working of Bourdon tube.

Last Answer : Construction and working : C type bourdon tube is made up of an elliptically flattened tube bent in such a way as to produce the C' shape as shown in the figure. One end (free ... displacement can be indication of applied pressure. Accuracy of this element is higher than C' type element.

Draw Bourdon tube with LVDT setup for pressure measurement.

Description : Draw Bourdon tube with LVDT setup for pressure measurement.

Last Answer : Bourdon tube with LVDT setup for pressure measurement.

Compare active transducer with passive transducer based on working principle, example, advantage, application

Description : Compare active transducer with passive transducer based on working principle, example, advantage, application

Last Answer : Compare active transducer with passive transducer based on working principle, example, advantage, application

Compare U tube manometer and well type manometer

Description : Compare U tube manometer and well type manometer

Last Answer : U-tube and well type manometer Sr.No. U-tube manometer well type manometer 1 Both legs are having same cross section area Both legs are having different cross section area ... cross section area. 5 Difference in heights in measured. Single height is measured.

Neighbor's dog bellows all day, is there a fix?

Description : Neighbor's dog bellows all day, is there a fix?

Last Answer : Many options. You could talk to the owner, or call the cops. Maybe poisoned tog dreats.

Why neoprene rubber bellows are used in IPBD?

Description : Why neoprene rubber bellows are used in IPBD?

Last Answer : Neoprene rubber bellows are used near the terminals of the equipment and also at building wall from indoor to outdoor area to allow thermal expansion and to minimise vibrations. 

Why neoprene rubber bellows in generator IPBD?

Description : Why neoprene rubber bellows in generator IPBD?

Last Answer : Prevent vibrations transmitted from generator to IPBD.  

The purpose of providing expansion bellows in the shell of tubular exchanger is to (A) Increase the heating load (B) Impart structural strength(C) Account for the uneven expansion of shell and tube bundles(D) Facilitate increase of shell length, if needed

Description : The purpose of providing expansion bellows in the shell of tubular exchanger is to (A) Increase the heating load (B) Impart structural strength (C) Account for the uneven expansion of shell and tube bundles (D) Facilitate increase of shell length, if needed

Last Answer : (C) Account for the uneven expansion of shell and tube bundles

State the working principle of Bellows pressure gauge with neat sketch.

Description : State the working principle of Bellows pressure gauge with neat sketch.

Last Answer : Bellows pressure gauge: Diagram: Principle: Bellows element is the elastic element which gets deflected at the free end when pressure is applied through fixed end. This free end deflection can be taken as the measure of pressure inside it.

List any two advantages and two applications of Bellows.

Description : List any two advantages and two applications of Bellows.

Last Answer : Advantages: - 1. It is used to measure absolute & differential pressure. 2. It is used to measure low or medium pressure rang. 3. Bellow joints do not require access; ... . 3. low pressure gauges are suitable for chemical, petrochemical, plant construction, and cleanrooms

List two advantages of capsule bellows.

Description : List two advantages of capsule bellows.

Last Answer : Advantages of capsule 1. High accuracy 2. Suitable for low pressure measurement.  Advantages of bellows 1. Good for low to moderate pressure range. 2. Adaptable for absolute and differential pressure.

State working principle of capacitive type level sensor with diagram.

Description : State working principle of capacitive type level sensor with diagram. 

Last Answer : Principle of working : The capacitive level detector operates on the equation of parallel plate capacitor, i.e. Where, C = capacitance value in farad ε = dielectric constant d = distance between ... (ε ). This principle is used in the capacitance level gauge for detecting level change.

Give construction working principle of RTD with a neat sketch.

Description : Give construction working principle of RTD with a neat sketch.

Last Answer : Diagram Working: An RTD (resistance temperature detector) is a temperature sensor that operates on the measurement principle that a material's electrical resistance changes with temperature. ... change m resistance of the RTD, which is then used to calculate change in temperature.

Describe the need of level measurements.

Description : Describe the need of level measurements.

Last Answer : In almost all industries, vast quantities of liquid such as water ,solvents, chemicals etc. are used in number of processes. It is widely employed to monitor as well as measure ... and therefore its measurement becomes important in a variety of processes encountered in modern manufacturing plants.

Describe the construction of orifice plate flow meter.

Description : Describe the construction of orifice plate flow meter. 

Last Answer : It is variable head flow meter in which the differential pressure is developed by using orifice plate by inserting it in the path of the fluid flow.  Orifice meter is as ... measurement of differential pressure. Thus differential pressure (p1-p2) is directly proportional to the flowrate.

Describe construction of bimetallic thermometer

Description : Describe construction of bimetallic thermometer

Last Answer : Construction and working : Figure shows construction of bimetallic thermometer, it consists of bimetallic strip usually in the form of a cantilever beam, which is prepared from two thin strips ... . This type of thermometer is used in homes and offices for indicating ambient temperature.

State working principle of piezoelectric transducer with diagram.

Description : State working principle of piezoelectric transducer with diagram.

Last Answer : Working principle: When force or pressure is applied to the piezoelectric material like quartz crystal or barium titanate, then an e.m.f. is generated across the material or vice versa ... deformation generates a charges and this charges appears as a voltage across the electrodes.

List the different level measurement methods.

Description : List the different level measurement methods. 

Last Answer : Liquid Level Measurement Direct method 1. Hook type 2. Sight glass gype 3. Float type 4. Dip stick Indirect method 1. Hydraustatic pressure type 2. Electrical type a) Capacitance level indicator b) Radiation level detector c) Ultrasonic level gauge 3. Radar type

List variable flow meter.

Description : List variable flow meter. 

Last Answer : 1. Variable area : Rotameter 2. Variable head : a) Venturi b) Orifice c) Pitot tube d) Nozzle

Define absolute pressure, atmospheric pressure.

Description : Define absolute pressure, atmospheric pressure.

Last Answer : Absolute Pressure : Absolute pressure is defined as actual total pressure including atmospheric pressure acting on a surface  Unit of absolute pressure is pounds per square inch absolute and it ... by the air surrounding to the earth. Unit of atmospheric pressure is Pounds per square inch.

Draw Hysteresis loop for Hard steel and soft steel. Also write one application of each material.

Description : Draw Hysteresis loop for Hard steel and soft steel. Also write one application of each material.

Last Answer : Application of Hard steel:  Fig. (a) Shows hysteresis loop for hard steel. Such materials are used for producing permanent magnets. Such a hysteresis loop represents a large residual ... Residual flux & coercive force are less. Hence material can be used for making the electromagnets. 

for Delta-Star connection of 3-phase transformer: i) Draw the connection diagram ii) List any two advantages of this connection iii) State its area of application.

Description : for Delta-Star connection of 3-phase transformer: i) Draw the connection diagram ii) List any two advantages of this connection iii) State its area of application. 

Last Answer : Disadvantages: i) In this type of connection, the secondary voltage is not in phase with the primary. Hence it is not possible to operate this connection in parallel with star-star or delta-delta ... iv) As line current is equal to phase current the conductor size of winding should be large. 

What is a manometer ?

Description : What is a manometer ?

Last Answer : An instrument that can be used to determine the pressure of a gas is called a manometer.

Manometer What ?

Last Answer : of gas Stress Diagnostic Instrument.

Differential Manometer What ?

Last Answer : that Manometer With the help The same Of pipes Two To the point Or Two Different Of pipes In Stress The difference Diagnosis To do Is Him , differential Manometer Says.

An instrument to detect the purity of milk is _____? A. Lactometer B. Manometer C. Sonometer D. Hygrometer

Description : An instrument to detect the purity of milk is _____? A. Lactometer B. Manometer C. Sonometer D. Hygrometer

Last Answer : ANSWER: A

An instrument to detect the purity of milk is _____? A. Lactometer B. Manometer C. Sonometer D. Hygrometer

Description : An instrument to detect the purity of milk is _____? A. Lactometer B. Manometer C. Sonometer D. Hygrometer

Last Answer : ANSWER: A

D.C. propulsion motor brush pressure depends on the brush grade used and in practice is set with a ______________. A. multimeter B. manometer C. spring scale D. compound gauge

Description : D.C. propulsion motor brush pressure depends on the brush grade used and in practice is set with a ______________. A. multimeter B. manometer C. spring scale D. compound gauge

Last Answer : Answer: C

The charge of a lead-acid battery is checked with a _____________. A. manometer B. hydrometer C. viscosimeter D. ohmmeter

Description : The charge of a lead-acid battery is checked with a _____________. A. manometer B. hydrometer C. viscosimeter D. ohmmeter

Last Answer : Answer: B

The charge of a lead-acid battery is checked with a/an ____________. A. manometer B. hydrometer C. voltmeter D. ohmmeter

Description : The charge of a lead-acid battery is checked with a/an ____________. A. manometer B. hydrometer C. voltmeter D. ohmmeter

Last Answer : Answer: B

The instrument which measures very high temperature is------? A. Manometer B. Thermostat C. Chronometer D. Pyrometer (Answer) E. None of these

Description : The instrument which measures very high temperature is------? A. Manometer B. Thermostat C. Chronometer D. Pyrometer (Answer) E. None of these

Last Answer : D. Pyrometer (Answer)

An instrument commonly used for the measurement of atmospheric pressure is known as A. Manometer B. Barometer C. Calorimeter D. Potentiometer

Description : An instrument commonly used for the measurement of atmospheric pressure is known as A. Manometer B. Barometer C. Calorimeter D. Potentiometer

Last Answer :  Barometer

Apparatus to measure rate of respiration and R.Q. is (a) auxanometer (b) potometer (c) respirometer (d) manometer.

Description : Apparatus to measure rate of respiration and R.Q. is (a) auxanometer (b) potometer (c) respirometer (d) manometer.

Last Answer : (c) respirometer

Pressure difference between two points in vessels, pipelines or in two different pipelines can be measured by a differential manometer. The pressure difference measured as the mm of water column in case of mercury-water, differential manometer is equal to (where, H = difference in height of mercury column in mm). (A) H (B) 12.6 H (C) 13.6 H (D) 14.6 H

Description : Pressure difference between two points in vessels, pipelines or in two different pipelines can be measured by a differential manometer. The pressure difference measured as the mm of water column in case of mercury-water, differential manometer is ... mm). (A) H (B) 12.6 H (C) 13.6 H (D) 14.6 H

Last Answer : (B) 12.6 H

Two liquids manometer is used for measuring small pressure differences in (A) Liquids (B) Gases (C) Mixture of hydrocarbons (D) None of these

Description : Two liquids manometer is used for measuring small pressure differences in (A) Liquids (B) Gases (C) Mixture of hydrocarbons (D) None of these

Last Answer : (A) Liquids

Working principle of manometer comprises of balancing a coloumn of liquid against the pressure to be measured. Inclined tube manometer is especially used for the measurement of __________ pressure. (A) Small differential (B) Atmospheric (C) Absolute (D) Gage

Description : Working principle of manometer comprises of balancing a coloumn of liquid against the pressure to be measured. Inclined tube manometer is especially used for the measurement of __________ pressure. (A) Small differential (B) Atmospheric (C) Absolute (D) Gage

Last Answer : (A) Small differential

Small pressure differences in liquids is measured using a/an (A) U-tube manometer (B) Inclined tube manometer (C) Pitot tube (D) None of these

Description : Small pressure differences in liquids is measured using a/an (A) U-tube manometer (B) Inclined tube manometer (C) Pitot tube (D) None of these

Last Answer : (B) Inclined tube manometer

Bed pressure drop in an air fluidised bed of catalyst particles (ρp = 200 kg/m3, Dp = 0.05 cm) of 60 cm bed depth and bed porosity of 0.5 expressed in cm of water (manometer) is (A) 90 (B) 60 (C) 45 (D) 30

Description : Bed pressure drop in an air fluidised bed of catalyst particles (ρp = 200 kg/m3, Dp = 0.05 cm) of 60 cm bed depth and bed porosity of 0.5 expressed in cm of water (manometer) is (A) 90 (B) 60 (C) 45 (D) 30

Last Answer : (B) 60

Very small pressure difference (< 5 mm water column) can be most conveniently measured by a/an __________ manometer. (A) U-tube water (B) U-tube mercury (C) Inclined tube mercury (D) Inclined tube water

Description : Very small pressure difference (< 5 mm water column) can be most conveniently measured by a/an __________ manometer. (A) U-tube water (B) U-tube mercury (C) Inclined tube mercury (D) Inclined tube water

Last Answer : (D) Inclined tube water

Differential manometer measures the (A) Atmospheric pressure (B) Sub-atmospheric pressure (C) Pressure difference between two points (D) None of these

Description : Differential manometer measures the (A) Atmospheric pressure (B) Sub-atmospheric pressure (C) Pressure difference between two points (D) None of these

Last Answer : (C) Pressure difference between two points

A mercury (specific gravity = 13.6) manometer connected across an orificemeter fitted in a pipe shows a manometer reading of 2 cms. If the manometer liquid is changed to carbon tetrachloride (specific gravity = 1.6), then for the same flow rate of water the new manometer reading will be __________ cms. (A) 17 (B) 42(C) 84 (D) 1.8

Description : A mercury (specific gravity = 13.6) manometer connected across an orificemeter fitted in a pipe shows a manometer reading of 2 cms. If the manometer liquid is changed to carbon tetrachloride (specific gravity = 1.6), then ... new manometer reading will be __________ cms. (A) 17 (B) 42 (C) 84 (D) 1.8

Last Answer : __________ cms. (A) 17

2. Differential manometer measures the (A) Absolute pressure (B) Gauge pressure (C) Pressure difference (D) Pressure gradien

Description : 2. Differential manometer measures the (A) Absolute pressure (B) Gauge pressure (C) Pressure difference (D) Pressure gradien

Last Answer : (C) Pressure difference

Flow rate of high velocity flue gas discharged through a stack to the atmosphere can be most conveniently measured by a (A) Pitot tube (B) Manometer (C) Rotameter (D) None of these

Description : Flow rate of high velocity flue gas discharged through a stack to the atmosphere can be most conveniently measured by a (A) Pitot tube (B) Manometer (C) Rotameter (D) None of these

Last Answer : (A) Pitot tube

Correction for capillary effect in manometers (used for pressure measurement) need not be applied, if diameter of the manometer tube is __________ mm. (A) < 4 (B) > 4 (C) > 12.5 (D) < 10

Description : Correction for capillary effect in manometers (used for pressure measurement) need not be applied, if diameter of the manometer tube is __________ mm. (A) < 4 (B) > 4 (C) > 12.5 (D) < 10

Last Answer : (C) > 12.5