Sauter mean diameter is the same as the __________ mean diameter. (A) Mass (B) Arithmetic (C) Volume-surface (D) Geometric

Sauter mean diameter is the same as the __________ mean diameter.
(A) Mass
(B) Arithmetic
(C) Volume-surface
(D) Geometric
by

1 Answer

Answer :

(C) Volume-surface
by

Related questions

Reciprocal of sphericity is termed as the (A) Specific surface ratio (B) Shape factor (C) Sauter diameter (D) Surface area per unit mass

Description : Reciprocal of sphericity is termed as the (A) Specific surface ratio (B) Shape factor (C) Sauter diameter (D) Surface area per unit mass

Last Answer : (B) Shape factor

__________ mean diameter of particles is given by Σ (xi /Dpi ⃗) (A) Mass (B) Volume (C) Arithmetic (D) Volume surface

Description : __________ mean diameter of particles is given by Σ (xi /Dpi ⃗) (A) Mass (B) Volume (C) Arithmetic (D) Volume surface

Last Answer : (B) Volume

In case of heat transfer by conduction in a hollow cylinder, __________ mean area is used to calculate the heat transfer rate. (A) Geometric (B) Arithmetic (C) Logarithmic (D) Either (A), (B) or (C)

Description : In case of heat transfer by conduction in a hollow cylinder, __________ mean area is used to calculate the heat transfer rate. (A) Geometric (B) Arithmetic (C) Logarithmic (D) Either (A), (B) or (C)

Last Answer : (C) Logarithmic

A two stage compressor is used to compress an ideal gas. The gas is cooled to the initial temperature after each stage. The intermediate pressure for the minimum total work requirement should be equal to the __________ mean of P1 and P2.(where, P1 and P2 are initial and final pressures respectively) (A) Logarithmic (B) Arithmetic (C) Geometric (D) Harmonic

Description : A two stage compressor is used to compress an ideal gas. The gas is cooled to the initial temperature after each stage. The intermediate pressure for the minimum total work requirement should be equal to ... final pressures respectively) (A) Logarithmic (B) Arithmetic (C) Geometric (D) Harmonic

Last Answer : (C) Geometric

When a vertical wall is subjected to pressures due to liquid on both sides, the resultant pressure is the __________ of the two pressures. (A) Sum (B) Difference (C) Arithmetic mean (D) Geometric mean

Description : When a vertical wall is subjected to pressures due to liquid on both sides, the resultant pressure is the __________ of the two pressures. (A) Sum (B) Difference (C) Arithmetic mean (D) Geometric mean

Last Answer : Answer: Option B

In the equation Q = UAΔt; Δt is (A) Geometric mean temperature difference (B) Arithmetic mean temperature difference (C) Logarithmic mean temperature difference (D) The difference of average bulk temperatures of hot and cold fluids

Description : In the equation Q = UAΔt; Δt is (A) Geometric mean temperature difference (B) Arithmetic mean temperature difference (C) Logarithmic mean temperature difference (D) The difference of average bulk temperatures of hot and cold fluids

Last Answer : (C) Logarithmic mean temperature difference

Terminal point temperature differences between fluids in case of a heat exchanger is termed as (A) Approach (B) Log mean temperature difference (C) Arithmetic mean temperature difference (D) Geometric mean temperature difference

Description : Terminal point temperature differences between fluids in case of a heat exchanger is termed as (A) Approach (B) Log mean temperature difference (C) Arithmetic mean temperature difference (D) Geometric mean temperature difference

Last Answer : (A) Approach

Which area is used in case of heat flow by conduction through a cylinder? (A) Logarithmic mean area (B) Arithmetic mean area (C) Geometric mean area (D) None of these

Description : Which area is used in case of heat flow by conduction through a cylinder? (A) Logarithmic mean area (B) Arithmetic mean area (C) Geometric mean area (D) None of these

Last Answer : (A) Logarithmic mean area

For heat flow through very thick walled cylinder, use _________mean radius. (A) Arithmetic (B) Logarithmic (C) Geometric (D) Either (A) or (C)

Description : For heat flow through very thick walled cylinder, use _________mean radius. (A) Arithmetic (B) Logarithmic (C) Geometric (D) Either (A) or (C)

Last Answer : (B) Logarithmic

For minimum work input in a two stage compression process the intermediated pressure is the A. Arithmetic process of suction and discharge pressure B. Logarithmic mean of suction and discharge pressure C. Geometric mean of suction and discharge pressure D. Hyperbolic mean of suction and discharge

Description : For minimum work input in a two stage compression process the intermediated pressure is the A. Arithmetic process of suction and discharge pressure B. Logarithmic mean of suction and discharge pressure C. Geometric mean of suction and discharge pressure D. Hyperbolic mean of suction and discharge

Last Answer : ANSWER : C

According to Malthusian theory of population - (1) Population increases in geometric ratio, food supply increases in arithmetic ratio (2) Population increases in arithmetic ratio, food supply increases in geometric ratio (3) Population increases in a harmonic mean, food supply increases in geometric ratio (4) Population increases in a harmonic ratio, food supply increases in a arithmetic ratio

Description : According to Malthusian theory of population - (1) Population increases in geometric ratio, food supply increases in arithmetic ratio (2) Population increases in arithmetic ratio, food supply increases in ... (4) Population increases in a harmonic ratio, food supply increases in a arithmetic ratio

Last Answer : (1) Population increases in geometric ratio, food supply increases in arithmetic ratio Explanation: In his 1798 work, An Essay on the Principle of Population, Malthus ermined the relationship between population ... e. by the repeated addition of a uniform increment in each uniform interval of time).

To calculate index number ----- mean is used (a) arithmetic (b) geometric © harmonic (d) none of the above.

Description : To calculate index number ----- mean is used (a) arithmetic (b) geometric © harmonic (d) none of the above.

Last Answer : (b) geometric

According to Malthusian theory of population (1) Population increases in geometric ratio, food supply increases in arithmetic ratio (2) Population increases in arithmetic ratio, food supply increases in geometric ratio (3) Population increases in a harmonic mean, food supply increases in geometric ratio (4) Population increases in a harmonic ratio, food supply increases in a arithmetic ratio

Description : According to Malthusian theory of population (1) Population increases in geometric ratio, food supply increases in arithmetic ratio (2) Population increases in arithmetic ratio, food supply increases in ... (4) Population increases in a harmonic ratio, food supply increases in a arithmetic ratio 

Last Answer : Population increases in geometric ratio, food supply increases in arithmetic ratio

Difference between geometric and arithmetic growth? -Biology

Description : Difference between geometric and arithmetic growth? -Biology

Last Answer : answer:

Which explains why the sequence 216 12 23 is arithmetic or geometric?

Description : Which explains why the sequence 216 12 23 is arithmetic or geometric?

Last Answer : The sequence 216 12 23 is neither arithmetic nor geometric.

The volume of a certain rectangular solid is 8 cm^3. Its total surface area is 32 cm^2 and its three dimensions are in geometric progression. -Maths 9th

Description : The volume of a certain rectangular solid is 8 cm^3. Its total surface area is 32 cm^2 and its three dimensions are in geometric progression. -Maths 9th

Last Answer : (b) 32 Let the edges of the solid be a, ar, ar2. Then, Volume = a x ar x ar2 = a3r3 = (ar)3. Given (ar)3 = 8 ⇒ ar = 2 Also, surface area = 2(a x ar + ar x ar2 + a × ar2) = 2(a2r + ... Given, 2ar (a + ar + ar2) = 32 ⇒ 4(a + ar + ar2) = 32 ; Sum of lengths of all edges = 32.

Three solid objects of the same material and of equal mass-a sphere, a cylinder (length = diameter) and a cube are at 500°C initially. These are dropped in a quenching bath containing a large volume of cooling oil each attaining the bath temperature eventually. The time required for 90% change in temperature is the smallest for (A) Cube (B) Cylinder (C) Sphere (D) Equal for all the three

Description : Three solid objects of the same material and of equal mass-a sphere, a cylinder (length = diameter) and a cube are at 500°C initially. These are dropped in a quenching bath containing a large volume of cooling oil ... (A) Cube (B) Cylinder (C) Sphere (D) Equal for all the three

Last Answer : (A) Cube

. Equivalent diameter of a particle is the diameter of the sphere having the same (A) Ratio of surface to volume as the actual volume (B) Ratio of volume to surface as the particle (C) Volume as the particle (D) None of these

Description : . Equivalent diameter of a particle is the diameter of the sphere having the same (A) Ratio of surface to volume as the actual volume (B) Ratio of volume to surface as the particle (C) Volume as the particle (D) None of these

Last Answer : (A) Ratio of surface to volume as the actual volume

The overall resistance for heat transfer through a series of flat resistance, is the __________ of the resistances. (A) Average (B) Geometric mean (C) Product (D) Sum

Description : The overall resistance for heat transfer through a series of flat resistance, is the __________ of the resistances. (A) Average (B) Geometric mean (C) Product (D) Sum

Last Answer : (D) Sum

. Which of the following equations is Rittinger's crushing law? (Where P = power required by the machine, m = feed rate, k = a constant, Ds̅a & D̅sb = volume surface mean diameter of feed & product respectively.) (A) P/m = K/ √Dp (B) P/m = K . ln D̅sa /D̅sb (C) P/m = K . (1/ D̅sb - 1/Ds̅a ) (D) None of these

Description : . Which of the following equations is Rittinger's crushing law? (Where P = power required by the machine, m = feed rate, k = a constant, Ds̅a & D̅sb = volume surface mean diameter of feed & product respectively.) (A) P/m = K/ ... K . ln D̅sa /D̅sb (C) P/m = K . (1/ D̅sb - 1/Ds̅a ) (D) None of these

Last Answer : (C) P/m = K . (1/ D̅sb - 1/Ds̅a )

If dp is the equivalent diameter of a non-spherical particle, Vp its volume and sp its surface area, then its sphericity is φs is defined by (A) φs = 6 Vp /dpsp (B) φs = Vp /dpsp (C) φs = 6 dpSp /Vp (D) φs = dpSp /Vp

Description : If dp is the equivalent diameter of a non-spherical particle, Vp its volume and sp its surface area, then its sphericity is φs is defined by (A) φs = 6 Vp /dpsp (B) φs = Vp /dpsp (C) φs = 6 dpSp /Vp (D) φs = dpSp /Vp

Last Answer : (A) φs = 6 Vp /dpsp

For spheres, the surface shape factor is given by (where, A = area, V = volume, and D = diameter) (A) π = (A/D2 ) (B) π/6 = (V/D3 ) (C) AD/V (D) None of these

Description : For spheres, the surface shape factor is given by (where, A = area, V = volume, and D = diameter) (A) π = (A/D2 ) (B) π/6 = (V/D3 ) (C) AD/V (D) None of these

Last Answer : (A) π = (A/D2 )

Sphericity for a non-spherical particle is given by (where, V and S are volume and surface area respectively of one particle. and, D = equivalent diameter of particle). (A) 6.V/D.S(B) V/6D.S (C) D.S/V (D) V/D.S

Description : Sphericity for a non-spherical particle is given by (where, V and S are volume and surface area respectively of one particle. and, D = equivalent diameter of particle). (A) 6.V/D.S (B) V/6D.S (C) D.S/V (D) V/D.S

Last Answer : (B) V/6D.S (C) D.S/V (D) V/D.S

In the following geometric modelling techniques. which cannot be used for finiteelement analysis: a.Wireframe modelling b.Surface modelling c.Solid modeling d.none of the above

Description : In the following geometric modelling techniques. which cannot be used for finiteelement analysis: a.Wireframe modelling b.Surface modelling c.Solid modeling d.none of the above

Last Answer : d.none of the above

In the following geometric modelling techniques which are not three-dimensionalmodelling? a.Wireframe modelling b.Drafting c.Surface modelling d.solid modelling

Description : In the following geometric modelling techniques which are not three-dimensionalmodelling? a.Wireframe modelling b.Drafting c.Surface modelling d.solid modelling

Last Answer : b.Drafting

true or false, the sum of all the areas of every surface on a geometric figure is the surface area

Description : true or false, the sum of all the areas of every surface on a geometric figure is the surface area

Last Answer : the answser is True

What is the meaning of the different symbols and abbreviations found on the documents that they use (such as surface finish to be achieved linear and geometric tolerances electronic components weld s?

Description : What is the meaning of the different symbols and abbreviations found on the documents that they use (such as surface finish to be achieved linear and geometric tolerances electronic components weld s?

Last Answer : Need answer

In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C. (A) 20 (B) 60 (C) 120 (D) ∞

Description : In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C. (A) 20 (B) 60 (C) 120 (D) ∞

Last Answer : (D) ∞

In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Description : In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Last Answer : (B) Square root

_________ is defined as the geometric mean of the relative rejections and the relative recoveries of two minerals. (A) Separation efficiency (B) Selectivity index (C) Concentration ratio (D) None of these

Description : _________ is defined as the geometric mean of the relative rejections and the relative recoveries of two minerals. (A) Separation efficiency (B) Selectivity index (C) Concentration ratio (D) None of these

Last Answer : (B) Selectivity index

If the volume of a sphere is numerically equal to its surface area, then find the diameter of the sphere. -Maths 9th

Description : If the volume of a sphere is numerically equal to its surface area, then find the diameter of the sphere. -Maths 9th

Last Answer : Let r be the radius of the sphere. and Volume of a sphere = surface area of the sphere ⇒ 4 / 3πr3 = 4πr2 ⇒ r = 3 cm ∴ Diameter of the sphere = 2r = 2 × 3 = 6 cm

If the volume of a sphere is numerically equal to its surface area, then find the diameter of the sphere. -Maths 9th

Description : If the volume of a sphere is numerically equal to its surface area, then find the diameter of the sphere. -Maths 9th

Last Answer : Let r be the radius of the sphere. and Volume of a sphere = surface area of the sphere ⇒ 4 / 3πr3 = 4πr2 ⇒ r = 3 cm ∴ Diameter of the sphere = 2r = 2 × 3 = 6 cm

A piece of paper and a cricket ball are dropped from the same height. Under which of the following conditions do both reach the surface simultaneously? (1) They must have the same volume (2) They must have the same density (3) They must have the same mass (4) They must be dropped in vacuum

Description : A piece of paper and a cricket ball are dropped from the same height. Under which of the following conditions do both reach the surface simultaneously? (1) They must have the same volume (2) They must have the same density (3) They must have the same mass (4) They must be dropped in vacuum

Last Answer : (4) They must be dropped in vacuum Explanation: When a piece of paper and a cricket ball are dropped from the same height, they reach the surface at different time because the shape of the paper ... occurring on them and this leads to a conclusion that both the article reaches at the same time.

A piece of paper and a cricket ball are dropped from the same height. Under which of the following conditions do both reach the surface simultaneously? (1) They must have the same volume (2) They must have the same density (3) They must have the same mass (4) They must be dropped in vacuum

Description : A piece of paper and a cricket ball are dropped from the same height. Under which of the following conditions do both reach the surface simultaneously? (1) They must have the same volume (2) They must have the same density (3) They must have the same mass (4) They must be dropped in vacuum

Last Answer : (4) They must be dropped in vacuum Explanation: When a piece of paper and a cricket ball are dropped from the same height, they reach the surface at different time because the shape of the paper ... occurring on them and this leads to a conclusion that both the article reaches at the same time.

A piece of paper and a cricket ball are dropped from the same height. Under which of the following conditions do both reach the surface simultaneously ? (1) They must have the same volume (2) They must have the same density (3) They must have the same mass (4) They must be dropped in vacuum

Description : A piece of paper and a cricket ball are dropped from the same height. Under which of the following conditions do both reach the surface simultaneously ? (1) They must have the same volume (2) They must have the same density (3) They must have the same mass (4) They must be dropped in vacuum

Last Answer : They must be dropped in vacuum

Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Description : Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Description : In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Last Answer : (D) All the above

Extensive properties of a thermodynamic system depend upon the __________ of the system. (A) Specific volume (B) Temperature (C) Mass (D) Pressure

Description : Extensive properties of a thermodynamic system depend upon the __________ of the system. (A) Specific volume (B) Temperature (C) Mass (D) Pressure

Last Answer : (C) Mass

Keeping the pressure constant, to double the volume of a given mass of an ideal gas at 27°C, the temperature should be raised to __________ °C. (A) 270 (B) 327 (C) 300 (D) 540

Description : Keeping the pressure constant, to double the volume of a given mass of an ideal gas at 27°C, the temperature should be raised to __________ °C. (A) 270 (B) 327 (C) 300 (D) 540

Last Answer : (B) 327

Specific surface area is the surface area of a unit __________ of materials. (A) Weight (B) Volume (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : Specific surface area is the surface area of a unit __________ of materials. (A) Weight (B) Volume (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (C) Either (A) or (B)

In Biot number, the characteristic length used is the ratio of the __________ of the solid. (A) Volume to surface area (B) Perimeter to surface area (C) Surface area to volume (D) Surface area to perimeter

Description : In Biot number, the characteristic length used is the ratio of the __________ of the solid. (A) Volume to surface area (B) Perimeter to surface area (C) Surface area to volume (D) Surface area to perimeter

Last Answer : (A) Volume to surface area

Helium-mercury method is used for the measurement of the __________ of the catalyst. (A) Surface area (B) Porosity (C) Pore volume (D) Both (B) & (C)

Description : Helium-mercury method is used for the measurement of the __________ of the catalyst. (A) Surface area (B) Porosity (C) Pore volume (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

. B.E.T. method can be used to determine the __________ of a porous catalyst. (A) Solid density (B) Pore volume (C) Surface area (D) All (A), (B) and (C)

Description : . B.E.T. method can be used to determine the __________ of a porous catalyst. (A) Solid density (B) Pore volume (C) Surface area (D) All (A), (B) and (C)

Last Answer : (C) Surface area

Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not exceed 4 (C) Both the rolls run necessarily at the same speed (D) Reduction ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Last Answer : (C) Both the rolls run necessarily at the same speed

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

What is geometric mean ?

Description : What is geometric mean ?

Last Answer : n To determine the geometric mean of a number, first the combined product of all the numbers is taken out , then the nth square root of that product is taken. Algebraically a1, a2, ..., an being the geometric average ... geometric mean , {\ displaystyle GM = {\ sqrt {2 \ cdot 8}} = 4.} ( See wiki).

What is the geometric mean of 6 and 11?

Description : What is the geometric mean of 6 and 11?

Last Answer : Feel Free to Answer

What is the geometric mean of 9 and 30?

Description : What is the geometric mean of 9 and 30?

Last Answer : What is the answer ?

whats the geometric mean of 25 and 35?

Description : whats the geometric mean of 25 and 35?

Last Answer : 15 is the geometric mean of 25 and 35.

If the relation between x and y in order that the `20^(th)` arithmetic mean between x and 2y is same as the `20^(th)` arithmetic mean between 2x and y

Description : If the relation between x and y in order that the `20^(th)` arithmetic mean between x and 2y is same as the `20^(th)` arithmetic mean between 2x and y

Last Answer : If the relation between x and y in order that the `20^(th)` arithmetic mean between x and 2y is same as ... inserted in each case )is y = Kx, find K.