Description : The primary purpose of the data modem is to A. interface analog terminal equipment to analog communications channel B. interface digital terminal equipment to analog communications ... to digital communications channel D. interface digital terminal equipment to digital communications channel
Last Answer : B. interface digital terminal equipment to analog communications channel
Description : The line control unit (LCU) operates on the data digital form. A. Data communications equipment (DCE) B. UART C. Modem D. Data terminal equipment (DTE)
Last Answer : D. Data terminal equipment (DTE)
Description : RS-232, RS-449, RS-530, V, 24 and X.21 are examples of ____________. A. standards for interfaces between modems and transmission facilities B. standards for various types of ... for interfaces between terminals and modems D. standards for end to end performance of data communications system
Last Answer : C. standards for interfaces between terminals and modems
Description : Which of the following is not referred to as data terminal equipment? A. Telephone set B. Printers C. Modem D. Computer
Last Answer : C. Modem
Description : Modem is referred to as ______. A. Universal asynchronous Rx/Tx B. Data communication equipment C. Universal synchronous Rx/Tx D. Data terminal equipment
Last Answer : B. Data communication equipment
Description : Describe function of each pin of 9 pin RS 232 connector.
Last Answer : An RS232 pinout 9 pin cable features nine pins: 1. Data Carrier Detect (DCD or CD) - After a data terminal is detected, a signal is sent to the data set that is going to be transmitted ... occurs, the data terminal is alerted, but the RI will not stop the flow of serial data between devices.
Description : Connector RJ-45 contains? a. Two pins b. Four pins c. Eight pins d. Ten pins
Last Answer : c. Eight pins
Description : Computers cannot communicate with each other directly over telephone lines because they usedigitalpulses whereas telephone lines useanalog sound frequencies. What is the name of the device which permits digital to analog ... A. Interface B. Modem C. Attenuation D. Teleprocessor E. None of the above
Last Answer : Modem
Description : The device that converts computer output for transmission over telephone lines is called (1) interface (2) interpreter (3) modem (4) I/O port
Last Answer : modem
Description : In __________ transmission, a unique SYNC character is transmitted at the beginning of each message. A. asynchronous B. synchronous C. digital D. analogue
Last Answer : B. synchronous
Description : The RS – 232 interface
Last Answer : interconnects data sets and the transmission circuits
Description : In which of the following terminals the screen is regarded as an array of pixels, where each pixel is either on or off: a) Character Map Terminal b) Bit Map Terminal c) RS 232 C Terminal d) None of The Above
Last Answer : b) Bit Map Terminal
Description : What is the data link protocol that is used in asynchronous transmission for transferring files from one computer to another? A. A modem B. X modem C. B modem D. C modem
Last Answer : B. X modem
Description : What is the data link protocol that is used in asynchronous transmission for transferring files from one computer to another? A. A modem B. X modem C. B modem
Description : ECE Board Exam March 1996 The expander in a companding device provides ___________. A. greater amplification for low signal levels B. less amplification for low signal levels C. greater amplification for high signal levels D. lesser pressure for transmission
Last Answer : B. less amplification for low signal levels
Description : These are used to connect non-ISDN equipment ot ISDN line. A. Digipeaters B. Terminal adapters C. Local repeaters D. Terminal repeaters
Last Answer : B. Terminal adapters
Description : Data aresent over pin _____ of the EIA-232 interface. A. 2 B. 3 C. 4 D. All of theabove
Last Answer : 2
Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection
Last Answer : A. input
Description : If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these
Last Answer : C. infinite
Description : Which of the following statement is correct? a. terminal section of a synchronous modem contains the scrambler b. receiver section of a synchronous modem contains the scrambler c. transmission section of ... d. control section of a synchronous modem contains the scrambler e. none of the above
Last Answer : transmission section of a synchronous modem contains the scrambler
Description : ECE Board Exam March 1996 What is the number of pins in the RS-232C interface? A. 25 B. 15 C. 20 D. 20
Last Answer : A. 25
Description : ECE Board Exam March 1996 The standard that specifies a balanced interface cable that will operate bit rates up to 10 Mbps with in a span distances up to 1200 m. A. RS-423A B. RS-422A C. RS-550A D. RS-449A
Last Answer : B. RS-422A
Description : Refers to the first generation of local loop system in telecommunication technology. A. GSM B. DECT C. Analogue cellular D. TACS
Last Answer : C. Analogue cellular
Description : What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz
Last Answer : D. 300-3400 Hz
Description : Transmission lines are either balanced or unbalanced with respect to _________. A. negative terminal B. input C. ground D. positive terminal
Last Answer : C. ground
Description : What is the other name for LAN Card ? 1) NIC 2) Network Connector 3) MODEM 4) Internet Card
Last Answer : 1) NIC
Description : What is the other name for LAN Card ? 1 NIC 2 Network Connector 3 MODEM 4 Internet Card
Last Answer : 1 NIC
Description : A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver
Last Answer : A. Antenna
Description : Professional Regulations Commission was created under ______. A. PD 323 B. PD 223 C. PD 232 D. RA 223
Last Answer : B. PD 223
Description : ECE Board Exam March 1996 The letter-number designation B8E is a form of modulation also known as ___________. A. pilot carrier system B. independent sideband emission C. lincomplex D. vestigial sideband transmission
Last Answer : B. independent sideband emission
Description : What is the insertion loss of connector-type splices for a single mode fiber optics? a. 0.51dB b. 0.31dB c. 0.49dB d. 0.38dB
Last Answer : d. 0.38dB
Description : What is the insertion loss of connector type splices for a single mode optical fiber? A. 0.51 dB B. 0.49 dB C. 0.31 dB D. 0.38 db
Last Answer : D. 0.38 db
Description : Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259
Last Answer : A. N-type connector
Description : Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259
Last Answer : B. F-type connector
Description : What connector is popular in attaching test instruments like oscilloscopes, frequency counters, spectrum analyzers, etc? A. UHF connector B. PL-259 C. BNC D. SMA
Last Answer : C. BNC
Description : Which of the following coaxial cable connectors is called the UHF connector? A. PL-259 B. BNC C. N-type connector D. F connector
Last Answer : A. PL-259
Description : Insertion loss of connector-type splices for a single-mode fiber cable. A. 0.2 dB B. 0.3 dB C. 0.09 dB D. 0.38 dB
Last Answer : D. 0.38 dB
Description : Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge
Last Answer : B. The transmitter and receiver
Description : Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem
Last Answer : C. Transmitter, channel and receiver
Description : A system that performs parallel-to-serial and serial-to-parallel conversion of data link. A. DCE B. DTE C. Modem D. PC
Last Answer : B. DTE
Description : The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem
Last Answer : D. Modem
Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter
Last Answer : A. Psophometer
Description : The transfer of data from a CPU to peripheral devices of computer is achieved through ________ A. Modem B. Interface C. Buffer D. I/O Ports
Last Answer : D. I/O Ports
Description : The use of telecommunication for the transmission of signals to initiate, modify or terminate functions of equipment at a distance. A. Tracking B. space command C. Telecommand D. Trunking
Last Answer : C. Telecommand
Description : The use of telecommunication for the transmission of signals to initiate, modify or terminate functions of equipment at a distance. A. Tracking B. Telemetry C. Telecommand D. Space telemetry
Description : In microcontroller and LCD interface which line will instruct the LCD that microcontroller is sending data? a) DB0 b) RW c) EN d) RS
Last Answer : d) RS
Description : Rules governing the transmission of digital information. A. Line protocol B. Isochronous C. Data communications D. Digital communications
Last Answer : B. Isochronous
Description : ECE Board Exam March 1996 What is the transmission rate of a system for transmitting the output of a microcomputer to a line printer operating at a speed of 30 lines/minute? Assume that the line printer has 8 bits ... and prints out 80 characters/line. A. 800 bps B. 400 bps C. 320 bps D. 640 bps
Last Answer : C. 320 bps
Description : Which of the following signal is not standard RS-232-C signal? a. VDR b. RTS c. CTS d. DSR
Last Answer : VDR
Description : ECE Board Exam March 1996 The K-factor under normal atmospheric conditions in a microwave radio data profile calculation is equal to ___________. A. 2/3 B. 0 C. 4/3 D. Infinity
Last Answer : C. 4/3