What are operations performed on data in 8085

What are operations performed on data in 8085
by

1 Answer

Answer :

The various operations performed are
•  Store 8-bit data
•  Perform arithmetic and logical operations
•  Test for conditions
•  Sequence the execution of instructions
•  Store data temporarily during execution in the defined R/W memory locations called the stack
by

Related questions

How many operations are there in the instruction set of 8085 microprocessor?

Description : How many operations are there in the instruction set of 8085 microprocessor?

Last Answer : There are 74 operations in the 8085 microprocessor.

Actual data processing operations are performed in the arithmetic logic section, but not in the …. Storage section of a processor unit a. Primary b. Accumulator c. Buffer d. Secondary

Description : Actual data processing operations are performed in the arithmetic logic section, but not in the …. Storage section of a processor unit a. Primary b. Accumulator c. Buffer d. Secondary

Last Answer : a. Primary

What are the three decisions making operations performed by the ALU of a computer? a. Grater than b. Less than c. Equal to d. All of the above

Description : What are the three decisions making operations performed by the ALU of a computer? a. Grater than b. Less than c. Equal to d. All of the above

Last Answer : d. All of the above

In the 8085A Microprocessor, arithmetic and logical operations are performed through which of the following?

Description : In the 8085A Microprocessor, arithmetic and logical operations are performed through which of the following? A) Stack B) ALU C) I/O D) Register 

Last Answer : In the 8085A Microprocessor, arithmetic and logical operations are performed through which of the following? A) Stack B) ALU C) I/O D) Register 

Why 8085 processor is called an 8 bit processor? a) Because 8085 processor has 8 bit ALU. b) Because 8085 processor has 8 bit data bus. c) a & b. Why 8085 processor is called an 8 bit processor? a) Because 8085 processor has 8 bit ALU. b) Because 8085 processor has 8 bit data bus. c) a & b.

Description : Why 8085 processor is called an 8 bit processor? a) Because 8085 processor has 8 bit ALU. b) Because 8085 processor has 8 bit data bus. c) a & b.

Last Answer : a) Because 8085 processor has 8 bit ALU.

How many machine cycles does 8085 have, mention them

Description : How many machine cycles does 8085 have, mention them

Last Answer : The 8085 have seven machine cycles. They are • Opcode fetch • Memory read • Memory write • I/O read • I/O write • Interrupt acknowledge • Bus idle

How many interrupts does 8085 have, mention them

Description : How many interrupts does 8085 have, mention them

Last Answer : The 8085 has 5 interrupt signals; they are INTR, RST7.5, RST6.5, RST5.5 and TRAP

Steps involved to fetch a byte in 8085

Description : Steps involved to fetch a byte in 8085

Last Answer : i. The PC places the 16-bit memory address on the address bus ii. The control unit sends the control signal RD to enable the memory chip iii. The byte from ... byte is placed in the instruction decoder of the microprocessor and the task is carried out according to the instruction

What is the signal classification of 8085

Description : What is the signal classification of 8085

Last Answer : All the signals of 8085 can be classified into 6 groups • Address bus • Data bus • Control and status signals • Power supply and frequency signals • Externally initiated signals • Serial I/O ports

Explain priority interrupts of 8085.

Description : Explain priority interrupts of 8085.

Last Answer : The 8085 microprocessor has five interrupt inputs. They are TRAP, RST 7.5, RST 6.5, RST 5.5, and INTR. These interrupts have a fixed priority of interrupt service. If two or more interrupts go ... 8085 is shown in the table. Interrupts Priority TRAP RST 7.5 RST 6.5 RST 5.5 INTR

List the four instructions which control the interrupt structure of the 8085 microprocessor.

Description : List the four instructions which control the interrupt structure of the 8085 microprocessor.

Last Answer : • DI ( Disable Interrupts ) • EI ( Enable Interrupts ) • RIM ( Read Interrupt Masks ) • SIM ( Set Interrupt Masks )

List out the five categories of the 8085 instructions. Give examples of the instructions for each group.

Description : List out the five categories of the 8085 instructions. Give examples of the instructions for each group.

Last Answer : • Data transfer group – MOV, MVI, LXI. • Arithmetic group – ADD, SUB, INR. • Logical group –ANA, XRA, CMP. • Branch group – JMP, JNZ, CALL. • Stack I/O and Machine control group – PUSH, POP, IN, HLT.

What is the function of IO/M signal in the 8085?

Description : What is the function of IO/M signal in the 8085?

Last Answer : It is a status signal. It is used to differentiate between memory locations and I/O operations. When this signal is low (IO/M = 0) it denotes the memory related operations. When this signal is high (IO/M = 1) it denotes an I/O operation.

List the allowed register pairs of 8085.

Description : List the allowed register pairs of 8085.

Last Answer : • B-C register pair • D-E register pair • H-L register pair

List the 16 – bit registers of 8085 microprocessor.

Description : List the 16 – bit registers of 8085 microprocessor.

Last Answer : Stack pointer (SP) and Program counter (PC).

What is Microprocessor? Give the power supply & clock frequency of 8085

Description : What is Microprocessor? Give the power supply & clock frequency of 8085

Last Answer : A microprocessor is a multipurpose, programmable logic device that reads binary instructions from a storage device called memory accepts binary data as input and processes data according ... provides result as output. The power supply of 8085 is +5V and clock frequency in 3MHz.

What type of architecture is used in 8085 microprocessor?

Description : What type of architecture is used in 8085 microprocessor?

Last Answer : Ans- INTEL 8085 is a 8-bit microprocessor. It's based on Von-Neumann architecture in which the data and instructions are in the same memory space without any distinction between them. Data line: 8-bits--Can ... of data at a time. Address line: 16-bits--Can address upto 2^16(64KB) of address space.

What is function of ALE in 8085 microprocessor?

Description : What is function of ALE in 8085 microprocessor?

Last Answer : Ans-AlE stands for the address latch enableit 's working is that it differentiate the address and data bus in microprocessor.when it is high it select address bus .when it is low it select data bus.

How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Description : How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Last Answer : a. 2.5 Million instruction per second

Which is 16 Bit microprocessor: a. 8088 b. 8086 c. 8085 d. All of these

Description : Which is 16 Bit microprocessor: a. 8088 b. 8086 c. 8085 d. All of these

Last Answer : d. All of these

Which is the main feature of 8085: a. Internal clock generator b. Internal system controller c. Higher clock frequency d. All of these

Description : Which is the main feature of 8085: a. Internal clock generator b. Internal system controller c. Higher clock frequency d. All of these

Last Answer : d. All of these

In 1977 which corporation introduced an updated version of the 8080- the 8085: a. Motorola b. Intel c. Rockwell d. National

Description : In 1977 which corporation introduced an updated version of the 8080- the 8085: a. Motorola b. Intel c. Rockwell d. National

Last Answer : b. Intel

Which year Intel corporation introduced an updated version of the 8080- the 8085: a. 1965 b. 1976 c. 1977 d. 1985

Description : Which year Intel corporation introduced an updated version of the 8080- the 8085: a. 1965 b. 1976 c. 1977 d. 1985

Last Answer : c. 1977

Intel used HMOS technology to recreate_____: a. 8084 A b. 8086 A c. 8085 A d. 8088 A

Description : Intel used HMOS technology to recreate_____: a. 8084 A b. 8086 A c. 8085 A d. 8088 A

Last Answer : c. 8085 A

Which are some of popular processor: a. Motorola 6800 and 6809 b. Intel 8085 c. Zilog Z80 d. All the above

Description : Which are some of popular processor: a. Motorola 6800 and 6809 b. Intel 8085 c. Zilog Z80 d. All the above

Last Answer : d. All the above

The___ was very successful in the calculator market at that time: a. Motorola 6800 and 6809 b. Microprocessor 4004 c. Intel 8085 d. None of these

Description : The___ was very successful in the calculator market at that time: a. Motorola 6800 and 6809 b. Microprocessor 4004 c. Intel 8085 d. None of these

Last Answer : b. Microprocessor 4004

Microprocessor 8085 can address location upto a. 32K b. 128K c. 64K d. 1M

Description : Microprocessor 8085 can address location upto a. 32K b. 128K c. 64K d. 1M

Last Answer : c. 64K

.In an 8085 based system, the maximum number of input output devices can be connectedusing I/0 mapped I/O method isa) 64 b) 512 c) 256 d) 65536

Description : .In an 8085 based system, the maximum number of input output devices can be connectedusing I/0 mapped I/O method isa) 64 b) 512 c) 256 d) 65536

Last Answer : b) 512

8253, 8257 c) 8257,8251 d)8251,825721.Consider the following set of 8085 instruction.MVI A,82HORA AJP DSPLYXRA ADSPLY:OUT PORT1HLT.The output at PORT1 isa) 00H b) FFH c) 92H d) 11H

Description : 8253, 8257 c) 8257,8251 d)8251,825721.Consider the following set of 8085 instruction.MVI A,82HORA AJP DSPLYXRA ADSPLY:OUT PORT1HLT.The output at PORT1 isa) 00H b) FFH c) 92H d) 11H

Last Answer : a) 00H

The number of software interrupts in 8085 is ____ a) 5 b) 8

Description : The number of software interrupts in 8085 is ____ a) 5 b) 8

Last Answer : b) 8

To put the 8085 microprocessor in the wait state(i) lower the-HOLD input (ii) lower the READY input (iii) raise the HOLD input(iv) raise the READY input

Description : To put the 8085 microprocessor in the wait state(i) lower the-HOLD input (ii) lower the READY input (iii) raise the HOLD input(iv) raise the READY input

Last Answer : (ii) lower the READY input

In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set

Description : In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set

Last Answer : (A) set, reset

Accumulator based microprocessor example are: a. Intel 8085 b. Motorola 6809 c. A and B d. None of these

Description : Accumulator based microprocessor example are: a. Intel 8085 b. Motorola 6809 c. A and B d. None of these

Last Answer : c. A and B

Which stack is used in 8085? a) FIFO b) LIFO c) FILO

Description : Which stack is used in 8085? a) FIFO b) LIFO c) FILO

Last Answer : b) LIFO

Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Description : Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Last Answer : b) RST7.5 is a raising edge-trigging interrupt.

In 8085 name the 16 bit registers? a) Stack pointer b) Program counter c) a & b

Description : In 8085 name the 16 bit registers? a) Stack pointer b) Program counter c) a & b

Last Answer : c) a & b

Explain Briefly The Flag Register In The 8085 Microprocessor.?

Description : Explain Briefly The Flag Register In The 8085 Microprocessor.?

Last Answer : Answer :The flag register in 8085 is an 8-bit register which contains 5 bit positions. These five flags are of 1bit F/F and are known as zero, sign, carry, parity and auxiliary carry. ... addition and subtraction operations. The parity flag is used for results containing an even number of one's.

Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Description : Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Last Answer : Answer :The various functional blocks of the 8085 microprocessor are: Registers Arithmetic logic unit Address buffer Increment / decrement address latch Interrupt control Serial I/O control Timing and control circuitry Instructions decoder and machine cycle encoder.

How Can Signals Be Classified For The 8085 Microprocessor?

Description : How Can Signals Be Classified For The 8085 Microprocessor?

Last Answer : Answer :The signals of the 8085 microprocessor based on their functions can be classified into 7 categories namely: Frequency and power signals Address and data buses The control bus Interrupt Signals Serial Input / Output signals DMA signals Reset Signals

Enlist the features of 8085 microprocessor.

Description : Enlist the features of 8085 microprocessor.

Last Answer : Features of 8085 microprocessor: 1. 16 address line so 216=64 Kbytes of memory can be addressed. 2. Operating clock frequency is 3MHz and minimum clock  frequency is 500 KHz. 3. On chip bus ... cycle TTL clock 10. Provide 2 serial I/O lines, so peripheral can be interfaced with  8085 μp

Describe the functions of stack pointer and program counter of 8085.

Description : Describe the functions of stack pointer and program counter of 8085. 

Last Answer : Stack pointer: 1. It is a 16 bit register which is used to store the address of topmost filled memory location of stack memory. 2. SP always points current top of stack. 3. If data is ... of memory and in 8085 the address of memory is 16 bit. Hence program counter is 16 bit register.

State the functions of following pins of 8085 1) SOD 2) HLDA

Description : State the functions of following pins of 8085 1) SOD 2) HLDA

Last Answer : 1) SOD: Serial Output data SOD pin is used to transmit data serially from accumulator to the external devices connected to the pin.  2) HLDA: Microprocessor generates HLDA signal to acknowledge requesting device after HOLD signal.

State the functions of temporary registers of 8085 microprocessor.

Description : State the functions of temporary registers of 8085 microprocessor.

Last Answer : Temp Register (8 bits) is also called as operand register as it is used by μp for storing one of the operands during an operation and also for storing the result of any execution temproary.

List any four salient features of 8085 microprocessor

Description : List any four salient features of 8085 microprocessor

Last Answer : Features of 8085:  1. 16 address line so 216=64 Kbytes of memory can be addressed.  2. Operating clock frequency is 3MHz and minimum clock frequency is 500 KHz.  3. On chip bus controller ... duty cycle TTL clock  10. Provide 2 serial I/O lines, so peripheral can be interfaced with 8085 μp

The 8085 Microprocessor has

Description : The 8085 Microprocessor has A) 8-bits Data bus and 16-bits Address bus B) 8-bits Data bus and 8-bits Address bus C) 16-bits Data bus and 16-bits Address bus D) 32-bits Data bus and 8-bits Address bus 

Last Answer : B) 8-bits Data bus and 8-bits Address bus. 

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require

Description : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Last Answer : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Then number of T-states of the instruction STA in 8085 microprocessor is

Description : Then number of T-states of the instruction STA in 8085 microprocessor is A) 10 B) 12 C) 13 D) 16 

Last Answer : Then number of T-states of the instruction STA in 8085 microprocessor is 13 

What is the size of memory which can be accessed by direct accessing in 8085 microprocessor?

Description : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

Last Answer : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

What is the size of SP register in 8085 microprocessor?

Description :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

Last Answer :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits