List the four instructions which control the interrupt structure of the 8085 microprocessor.

List the four instructions which control the interrupt structure of the 8085  microprocessor.
by

1 Answer

Answer :

•  DI ( Disable Interrupts )
•  EI ( Enable Interrupts )
•  RIM ( Read Interrupt Masks )
•  SIM ( Set Interrupt Masks )
by

Related questions

Which of the following instructions is not available in 8085 microprocessor?

Description : Which of the following instructions is not available in 8085 microprocessor? (A) LDA 3850 (B) XTHL (C) push PSW (D) LDAXH

Last Answer : Which of the following instructions is not available in 8085 microprocessor? (A) LDA 3850 (B) XTHL (C) push PSW (D) LDAXH

List any four salient features of 8085 microprocessor

Description : List any four salient features of 8085 microprocessor

Last Answer : Features of 8085:  1. 16 address line so 216=64 Kbytes of memory can be addressed.  2. Operating clock frequency is 3MHz and minimum clock frequency is 500 KHz.  3. On chip bus controller ... duty cycle TTL clock  10. Provide 2 serial I/O lines, so peripheral can be interfaced with 8085 μp

List the 16 – bit registers of 8085 microprocessor.

Description : List the 16 – bit registers of 8085 microprocessor.

Last Answer : Stack pointer (SP) and Program counter (PC).

List out the five categories of the 8085 instructions. Give examples of the instructions for each group.

Description : List out the five categories of the 8085 instructions. Give examples of the instructions for each group.

Last Answer : • Data transfer group – MOV, MVI, LXI. • Arithmetic group – ADD, SUB, INR. • Logical group –ANA, XRA, CMP. • Branch group – JMP, JNZ, CALL. • Stack I/O and Machine control group – PUSH, POP, IN, HLT.

Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Description : Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Last Answer : b) RST7.5 is a raising edge-trigging interrupt.

8086 is interfaced to two 8259s (Programmable interrupt controllers). If 8259s are in master slave configuration the number of interrupts available to the 8086 microprocessor is a) 8 b) 16 c) 15 d) 64

Description : 8086 is interfaced to two 8259s (Programmable interrupt controllers). If 8259s are in master slave configuration the number of interrupts available to the 8086 microprocessor is a) 8 b) 16 c) 15 d) 64

Last Answer : a) 8

A microprocessor retries instructions from : a. Control memory b. Cache memory c. Main memory d. Virtual memory

Description : A microprocessor retries instructions from : a. Control memory b. Cache memory c. Main memory d. Virtual memory

Last Answer : c. Main memory

How many operations are there in the instruction set of 8085 microprocessor?

Description : How many operations are there in the instruction set of 8085 microprocessor?

Last Answer : There are 74 operations in the 8085 microprocessor.

What is Microprocessor? Give the power supply & clock frequency of 8085

Description : What is Microprocessor? Give the power supply & clock frequency of 8085

Last Answer : A microprocessor is a multipurpose, programmable logic device that reads binary instructions from a storage device called memory accepts binary data as input and processes data according ... provides result as output. The power supply of 8085 is +5V and clock frequency in 3MHz.

What type of architecture is used in 8085 microprocessor?

Description : What type of architecture is used in 8085 microprocessor?

Last Answer : Ans- INTEL 8085 is a 8-bit microprocessor. It's based on Von-Neumann architecture in which the data and instructions are in the same memory space without any distinction between them. Data line: 8-bits--Can ... of data at a time. Address line: 16-bits--Can address upto 2^16(64KB) of address space.

What is function of ALE in 8085 microprocessor?

Description : What is function of ALE in 8085 microprocessor?

Last Answer : Ans-AlE stands for the address latch enableit 's working is that it differentiate the address and data bus in microprocessor.when it is high it select address bus .when it is low it select data bus.

How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Description : How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Last Answer : a. 2.5 Million instruction per second

Which is 16 Bit microprocessor: a. 8088 b. 8086 c. 8085 d. All of these

Description : Which is 16 Bit microprocessor: a. 8088 b. 8086 c. 8085 d. All of these

Last Answer : d. All of these

The___ was very successful in the calculator market at that time: a. Motorola 6800 and 6809 b. Microprocessor 4004 c. Intel 8085 d. None of these

Description : The___ was very successful in the calculator market at that time: a. Motorola 6800 and 6809 b. Microprocessor 4004 c. Intel 8085 d. None of these

Last Answer : b. Microprocessor 4004

Microprocessor 8085 can address location upto a. 32K b. 128K c. 64K d. 1M

Description : Microprocessor 8085 can address location upto a. 32K b. 128K c. 64K d. 1M

Last Answer : c. 64K

To put the 8085 microprocessor in the wait state(i) lower the-HOLD input (ii) lower the READY input (iii) raise the HOLD input(iv) raise the READY input

Description : To put the 8085 microprocessor in the wait state(i) lower the-HOLD input (ii) lower the READY input (iii) raise the HOLD input(iv) raise the READY input

Last Answer : (ii) lower the READY input

In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set

Description : In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set

Last Answer : (A) set, reset

Accumulator based microprocessor example are: a. Intel 8085 b. Motorola 6809 c. A and B d. None of these

Description : Accumulator based microprocessor example are: a. Intel 8085 b. Motorola 6809 c. A and B d. None of these

Last Answer : c. A and B

Explain Briefly The Flag Register In The 8085 Microprocessor.?

Description : Explain Briefly The Flag Register In The 8085 Microprocessor.?

Last Answer : Answer :The flag register in 8085 is an 8-bit register which contains 5 bit positions. These five flags are of 1bit F/F and are known as zero, sign, carry, parity and auxiliary carry. ... addition and subtraction operations. The parity flag is used for results containing an even number of one's.

Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Description : Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Last Answer : Answer :The various functional blocks of the 8085 microprocessor are: Registers Arithmetic logic unit Address buffer Increment / decrement address latch Interrupt control Serial I/O control Timing and control circuitry Instructions decoder and machine cycle encoder.

How Can Signals Be Classified For The 8085 Microprocessor?

Description : How Can Signals Be Classified For The 8085 Microprocessor?

Last Answer : Answer :The signals of the 8085 microprocessor based on their functions can be classified into 7 categories namely: Frequency and power signals Address and data buses The control bus Interrupt Signals Serial Input / Output signals DMA signals Reset Signals

Enlist the features of 8085 microprocessor.

Description : Enlist the features of 8085 microprocessor.

Last Answer : Features of 8085 microprocessor: 1. 16 address line so 216=64 Kbytes of memory can be addressed. 2. Operating clock frequency is 3MHz and minimum clock  frequency is 500 KHz. 3. On chip bus ... cycle TTL clock 10. Provide 2 serial I/O lines, so peripheral can be interfaced with  8085 μp

State the functions of temporary registers of 8085 microprocessor.

Description : State the functions of temporary registers of 8085 microprocessor.

Last Answer : Temp Register (8 bits) is also called as operand register as it is used by μp for storing one of the operands during an operation and also for storing the result of any execution temproary.

The 8085 Microprocessor has

Description : The 8085 Microprocessor has A) 8-bits Data bus and 16-bits Address bus B) 8-bits Data bus and 8-bits Address bus C) 16-bits Data bus and 16-bits Address bus D) 32-bits Data bus and 8-bits Address bus 

Last Answer : B) 8-bits Data bus and 8-bits Address bus. 

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require

Description : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Last Answer : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Then number of T-states of the instruction STA in 8085 microprocessor is

Description : Then number of T-states of the instruction STA in 8085 microprocessor is A) 10 B) 12 C) 13 D) 16 

Last Answer : Then number of T-states of the instruction STA in 8085 microprocessor is 13 

What is the size of memory which can be accessed by direct accessing in 8085 microprocessor?

Description : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

Last Answer : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

What is the size of SP register in 8085 microprocessor?

Description :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

Last Answer :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

The ALE line of an 8085 microprocessor is used to

Description : The ALE line of an 8085 microprocessor is used to (A) latch the output of an I/O instruction into an external latch. (B) deactivate the chip-select signal from memory devices. (C) find the interrupt ... of the TRAP interrupt. (D) latch the 8 bits of address lines AD7-AD0 into an external latch.

Last Answer : The ALE line of an 8085 microprocessor is used to latch the 8 bits of address lines AD7-AD0 into an external latch.

Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR

Description : Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR 

Last Answer : Answer: D

In 8086 microprocessor one of the following instructions is executed before an arithmeticoperation a. AAM b) AAD c) DAS d) DAA

Description : In 8086 microprocessor one of the following instructions is executed before an arithmeticoperation a. AAM b) AAD c) DAS d) DAA

Last Answer : b) AAD

In 8086 microprocessor one of the following instructions is executed before an arithmetic operation a) AAM b) AAD c) DAS d) DAA

Description : In 8086 microprocessor one of the following instructions is executed before an arithmetic operation a) AAM b) AAD c) DAS d) DAA

Last Answer : b) AAD

In an 8085 microprocessor, the contents of the Accumulator, after the following instructions are executed

Description : In an 8085 microprocessor, the contents of the Accumulator, after the following instructions are executed will become   XRA A   MVI B, F0 H   SUB B  (A) 01 H (B) 0F H (C) F0 H (D) 10 H

Last Answer : In an 8085 microprocessor, the contents of the Accumulator, after the following instructions are executed will become   XRA A   MVI B, F0 H   SUB B  (A) 01 H (B) 0F H (C) F0 H (D) 10 H

In an 8085 microprocessor, the contents of accumulator, after the following instructions are

Description : In an 8085 microprocessor, the contents of accumulator, after the following instructions are executed will become   XRA A   MVI B F0H   SUB B   (a) 01 H (b) 0F H (c) F0 H (d) 10 H

Last Answer : In an 8085 microprocessor, the contents of accumulator, after the following instructions are executed will become   XRA A   MVI B F0H   SUB B   (a) 01 H (b) 0F H (c) F0 H (d) 10 H

List the allowed register pairs of 8085.

Description : List the allowed register pairs of 8085.

Last Answer : • B-C register pair • D-E register pair • H-L register pair

List few applications of microprocessor-based system.

Description : List few applications of microprocessor-based system.

Last Answer : It is used: i. For measurements, display and control of current, voltage, temperature, pressure, etc. ii. For traffic control and industrial tool control. iii. For speed control of machines.

How many generation of microprocessor: a. Four b. Five c. Six d. Three

Description : How many generation of microprocessor: a. Four b. Five c. Six d. Three

Last Answer : b. Five

Enlist any four addressing modes of 8086 microprocessor.

Description : Enlist any four addressing modes of 8086 microprocessor.

Last Answer : Addressing modes of 8086 : 1. Immediate 2. Direct 3. Register 4. Register indirect 5. Indexed 6. Register relative 7. Based indexed 8. Relative based indexed 9. Implied

How many bit microprocessor still survives in low-end application such as microwave ovens and small control system: a. 4 bit b. 16 bit c. 32 bit d. 64 bit

Description : How many bit microprocessor still survives in low-end application such as microwave ovens and small control system: a. 4 bit b. 16 bit c. 32 bit d. 64 bit

Last Answer : a. 4 bit

Which is the components of microprocessor: a. Register unit b. Arithmetic and logical unit c. Timing and control unit d. All of these

Description : Which is the components of microprocessor: a. Register unit b. Arithmetic and logical unit c. Timing and control unit d. All of these

Last Answer : d. All of these

The ALU and control unit of most of the microcomputers are combined and manufacture on a single silicon chip. What is it called? a. monochip b. microprocessor c. ALU d. control unit

Description : The ALU and control unit of most of the microcomputers are combined and manufacture on a single silicon chip. What is it called? a. monochip b. microprocessor c. ALU d. control unit

Last Answer : b. microprocessor

What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? a. Bus control b. Interrupts c. Bus arbitration d. Status

Description : What type of control pins are needed in a microprocessor to regulate traffic on the bus, in order to prevent two devices from trying to use it at the same time? a. Bus control b. Interrupts c. Bus arbitration d. Status

Last Answer : c. Bus arbitration

Which is the microprocessor comprises: a. Register section b. One or more ALU c. Control unit d. All of these

Description : Which is the microprocessor comprises: a. Register section b. One or more ALU c. Control unit d. All of these

Last Answer : d. All of these

____is used to control the cache with two new control bits not present in the 80386 microprocessor. What are the bits used to control the 8K byte cache? a) CR0, CD, NW b) CR0, NW, PWT c) Control Register Zero, PWT, PCD d) none

Description : ____is used to control the cache with two new control bits not present in the 80386 microprocessor. What are the bits used to control the 8K byte cache? a) CR0, CD, NW b) CR0, NW, PWT c) Control Register Zero, PWT, PCD d) none

Last Answer : d) none

The purpose of the microprocessor is to control ______

Description : The purpose of the microprocessor is to control ______  A. memory B. switches C. processing D. tasks

Last Answer : The purpose of the microprocessor is to control memory 

What is meant by interrupt?

Description : What is meant by interrupt?

Last Answer : Interrupt is an external signal that causes a microprocessor to jump to a specific subroutine.

Serial port interrupt is generated, if ____ bits are seta) IE b) RI, IE c) IP, TI d) RI, TI

Description : Serial port interrupt is generated, if ____ bits are seta) IE b) RI, IE c) IP, TI d) RI, TI

Last Answer : d) RI, TI

The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Description : The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Last Answer : a. Interrupt

Which are the flags of status register: a. Over flow flag b. Carry flag c. Half carry flag d. Zero flag e. Interrupt flag f. Negative flag g. All of these

Description : Which are the flags of status register: a. Over flow flag b. Carry flag c. Half carry flag d. Zero flag e. Interrupt flag f. Negative flag g. All of these

Last Answer : g. All of these