At 100% modulation, the sum fo the effective voltages in both sidebands is equal to ______% of the unmodulated carrier voltage. A. 50 B. 71 C. 100 D. 25

At 100% modulation, the sum fo the effective voltages in both sidebands is equal to
______% of the unmodulated carrier voltage.
A. 50
B. 71
C. 100
D. 25
by

1 Answer

Answer :

B. 71
by

Related questions

In amplitude modulation technique the unmodulated carrier is referred to as having ______. A. 100% modulation B. 0% modulation C. 50% modulated D. Over modulated

Description : In amplitude modulation technique the unmodulated carrier is referred to as having ______. A. 100% modulation B. 0% modulation C. 50% modulated D. Over modulated

Last Answer : B. 0% modulation

A modulation which does not follow the sine wave pattern, it produces undesirable harmonics such as spurious emission A. 0% modulated B. Over-modulated C. Unmodulated D. 100% modulated

Description : A modulation which does not follow the sine wave pattern, it produces undesirable harmonics such as spurious emission A. 0% modulated B. Over-modulated C. Unmodulated D. 100% modulated

Last Answer : B. Over-modulated

An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Description : An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Last Answer : B. 66.66 W

For 100% modulation, total power is? a) same as the power of unmodulated signal b) twice as the power of unmodulated signal c) four times as the power of unmodulated signal d) one and half times as the power of unmodulated signal

Description : For 100% modulation, total power is? a) same as the power of unmodulated signal b) twice as the power of unmodulated signal c) four times as the power of unmodulated signal d) one and half times as the power of unmodulated signal

Last Answer : Ans: D

How many sidebands are present in the J3E mode? A. Two sidebands and a carrier B. One upper sideband C. One lower sideband D. Two carriers and one sideband

Description : How many sidebands are present in the J3E mode? A. Two sidebands and a carrier B. One upper sideband C. One lower sideband D. Two carriers and one sideband

Last Answer : B. One upper sideband

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

Which of the following is referred to as a radio emission without sidebands A. Analog B. Carrier C. Data D. Voice

Description : Which of the following is referred to as a radio emission without sidebands A. Analog B. Carrier C. Data D. Voice

Last Answer : B. Carrier

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Last Answer : D. 83%

100% modulation in AM means a corresponding increase in total power by: A. 25% B. 75% C. 100% D. 50%

Description : 100% modulation in AM means a corresponding increase in total power by: A. 25% B. 75% C. 100% D. 50%

Last Answer : D. 50%

For 100% modulation, power in each sideband is ________ of that of carrier? a) 50% b) 70% c) 60% d) 25%

Description : For 100% modulation, power in each sideband is ________ of that of carrier? a) 50% b) 70% c) 60% d) 25%

Last Answer : Ans: D

What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo-random list of channels? A. Frequency hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Description : What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo ... hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Last Answer : A. Frequency hopping

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the average audio modulating frequency C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Description : What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the ... audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Last Answer : C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency

In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Description : In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Last Answer : C. Type of modulation of the main carrier

This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Description : This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Last Answer : C. Dynamic instability

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

Modulation in which the modulated wave is always present. A. Carrier modulation B. Front-end C. Continuous modulation D. Log-periodic modulation

Description : Modulation in which the modulated wave is always present. A. Carrier modulation B. Front-end C. Continuous modulation D. Log-periodic modulation

Last Answer : C. Continuous modulation

The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Description : The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Last Answer : D. Type of information to be transmitted

The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Description : The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Last Answer : D. Type of modulation of the main carrier

Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Last Answer : A. RF carrier

Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these

Description : Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these

Last Answer : B. Modulation index

If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Description : If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Last Answer : A. 1.14 volts

The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Description : The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Last Answer : B. 120 kHz

ECE Board Exam March 1996 The letter-number designation B8E is a form of modulation also known as ___________. A. pilot carrier system B. independent sideband emission C. lincomplex D. vestigial sideband transmission

Description : ECE Board Exam March 1996 The letter-number designation B8E is a form of modulation also known as ___________. A. pilot carrier system B. independent sideband emission C. lincomplex D. vestigial sideband transmission

Last Answer : B. independent sideband emission

Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Description : Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Last Answer : D. Miscellaneous noise

A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Description : A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Last Answer : D. 8.36 kW

One important difference between wye-connected and delta-connected generators is that delta connections have ____________. A. line voltages equal to the vector sum of the phase voltages B. phase voltages 90° out of sync C. line current equal to the phase current D. line voltage equal to the phase voltage

Description : One important difference between wye-connected and delta-connected generators is that delta connections have ____________. A. line voltages equal to the vector sum of the phase voltages B. phase voltages 90° ... C. line current equal to the phase current D. line voltage equal to the phase voltage

Last Answer : Answer: D

How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Description : How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Last Answer : B. 200 kHz

In an AM transmitter with 100% modulation, the voltage of the final RF stage will be

Description : In an AM transmitter with 100% modulation, the voltage of the final RF stage will be

Last Answer : approximately four times the DC supply voltage

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%

What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Description : What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Last Answer : D. Efficiency = radiation resistance/total resistance x 100%

Which of the following statements is true concerning simple parallel resistance circuits? A. The total current flow equals the sum of the individual currents. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistance. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements is true concerning simple parallel resistance circuits? A. The total current flow equals the sum of the individual currents. B. The total current flow equals the ... resistance. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at

Description : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is A) 50 W B) 66 W C) 68 W D) 70 W 

Last Answer : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is 66 W

If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage

Description : If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be (A) 50.55 (B) 15.55 (C) 10.66 (D) 66.66

Last Answer : If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be 66.66

A 1000W carrier is amplitude modulated to a depth of 85%. Calculate the total power of the modulated wave? A. 1361.25 W B. 680.62 W C. 1425 W D. 712.5 W

Description : A 1000W carrier is amplitude modulated to a depth of 85%. Calculate the total power of the modulated wave? A. 1361.25 W B. 680.62 W C. 1425 W D. 712.5 W

Last Answer : A. 1361.25 W

How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Last Answer : B. 1.25 MHz

Determine the terrain sensitivity loss for a 4-GHz carrier that is propagating over a very dry, mountainous area. A. -1.25 dB B. -3.05 dB C. -2.01 dB D. -5.01 dB

Description : Determine the terrain sensitivity loss for a 4-GHz carrier that is propagating over a very dry, mountainous area. A. -1.25 dB B. -3.05 dB C. -2.01 dB D. -5.01 dB

Last Answer : A. -1.25 dB

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

n its Global Economic Outlook report, Fitch Ratings cut India's economic growth forecast for the next financial year 2019-20 starting from April 1 to ______% from its previous estimate of 7%

Description : n its Global Economic Outlook report, Fitch Ratings cut India's economic growth forecast for the next financial year 2019-20 starting from April 1 to ______% from its previous estimate of 7%

Last Answer : 6.8

Account Receivables lag impacts sales. At no credit terms, the appeal falls to about ______ %, at 30 days, appeal is _____ %, at 60 days, appeal is ______%. a. 98.5, 92, 65 b. 65, 92, 98.5 c. 70, 85, 99 d. none of the above, there is no impact

Description : Account Receivables lag impacts sales. At no credit terms, the appeal falls to about ______ %, at 30 days, appeal is _____ %, at 60 days, appeal is ______%. a. 98.5, 92, 65 b. 65, 92, 98.5 c. 70, 85, 99 d. none of the above, there is no impact

Last Answer : b. 65, 92, 98.5

Both frequency and phase modulation utilize ________ modulation A. Phase B. AM and FM C. Digital D. Angle

Description : Both frequency and phase modulation utilize ________ modulation A. Phase B. AM and FM C. Digital D. Angle

Last Answer : D. Angle

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

In amplitude modulation AM, if modulation index is more than 100% then:

Description : In amplitude modulation AM, if modulation index is more than 100% then: (1) Power of the wave increases. (2) Efficiency of transmission increases. (3) The wave gets distorted. (4) Bandwidth increases

Last Answer : In amplitude modulation AM, if modulation index is more than 100% then: The wave gets distorted.

Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Description : Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Last Answer : D. Dummy

What modulation is normally used with digital data? A. AM B. FM C. SSB D. QPSK

Description : What modulation is normally used with digital data? A. AM B. FM C. SSB D. QPSK

Last Answer : D. QPSK