Referred to an oscillator signal “leak through” from a properly neutralized amplifier such as a master oscillator power amplifier. A. Carrier B. Stray signal C. Back wave D. Loss wave

Referred to an oscillator signal “leak through” from a properly neutralized amplifier such as a
master oscillator power amplifier.
A. Carrier
B. Stray signal
C. Back wave
D. Loss wave
by

1 Answer

Answer :

C. Back wave
by

Related questions

If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Description : If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Last Answer : A. 1.14 volts

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Description : A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Last Answer : A. It will radiate harmonics

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Last Answer : B. Phase control

The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Description : The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Last Answer : B. Closer coupling between the oscillator and the antenna.

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

A 1000W carrier is amplitude modulated to a depth of 85%. Calculate the total power of the modulated wave? A. 1361.25 W B. 680.62 W C. 1425 W D. 712.5 W

Description : A 1000W carrier is amplitude modulated to a depth of 85%. Calculate the total power of the modulated wave? A. 1361.25 W B. 680.62 W C. 1425 W D. 712.5 W

Last Answer : A. 1361.25 W

The product of the power supplied to the antenna and its gain relative to a half-wave dipole in a given direction. A. Peak envelope power B. ERP C. Rated power D. Carrier power’

Description : The product of the power supplied to the antenna and its gain relative to a half-wave dipole in a given direction. A. Peak envelope power B. ERP C. Rated power D. Carrier power’

Last Answer : B. ERP

This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Description : This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Last Answer : C. Dynamic instability

In amplitude modulation technique the unmodulated carrier is referred to as having ______. A. 100% modulation B. 0% modulation C. 50% modulated D. Over modulated

Description : In amplitude modulation technique the unmodulated carrier is referred to as having ______. A. 100% modulation B. 0% modulation C. 50% modulated D. Over modulated

Last Answer : B. 0% modulation

Which of the following is referred to as a radio emission without sidebands A. Analog B. Carrier C. Data D. Voice

Description : Which of the following is referred to as a radio emission without sidebands A. Analog B. Carrier C. Data D. Voice

Last Answer : B. Carrier

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Description : Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Last Answer : D. Mixer

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 kW. What is the gain in dB obtain by the use of the reflector ? ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6

Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Description : Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Last Answer : C. Major lobe radiation

What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4

Description : What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4

Last Answer : D. T4

In radio signal emission designation, the fifth symbol means A. Details of signals B. Type of information transmitted C. Nature of multiplexing D. Nature of signal modulating the main carrier

Description : In radio signal emission designation, the fifth symbol means A. Details of signals B. Type of information transmitted C. Nature of multiplexing D. Nature of signal modulating the main carrier

Last Answer : C. Nature of multiplexing

What is the emission designation of a single sideband reduced carrier signal? A. H3E B. J3E C. R3E D. B8E

Description : What is the emission designation of a single sideband reduced carrier signal? A. H3E B. J3E C. R3E D. B8E

Last Answer : C. R3E

What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Description : What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Last Answer : B. T2 carrier system

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Description : In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Last Answer : C. Type of modulation of the main carrier

What is the first symbol of a radio signal transmission having an amplitude modulated signal carrier, double side band? A. C B. B C. H D. A

Description : What is the first symbol of a radio signal transmission having an amplitude modulated signal carrier, double side band? A. C B. B C. H D. A

Last Answer : D. A

A digital carrier facility used to transmit a DSI-formatted signal at 1.544. Mbps. A. T2 B. T1 C. T4 D. T3

Description : A digital carrier facility used to transmit a DSI-formatted signal at 1.544. Mbps. A. T2 B. T1 C. T4 D. T3

Last Answer : B. T1

A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Description : A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Last Answer : A. Constant peak amplitude

Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Last Answer : A. RF carrier

The transformer signal coding method for T1 carrier is A. Binary B. NRZ C. Manchester D. Bipolar

Description : The transformer signal coding method for T1 carrier is A. Binary B. NRZ C. Manchester D. Bipolar

Last Answer : D. Bipolar

Modulation in which the modulated wave is always present. A. Carrier modulation B. Front-end C. Continuous modulation D. Log-periodic modulation

Description : Modulation in which the modulated wave is always present. A. Carrier modulation B. Front-end C. Continuous modulation D. Log-periodic modulation

Last Answer : C. Continuous modulation

Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Last Answer : D. 83%

The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Description : The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Last Answer : A. 1

What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Description : What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Last Answer : B. Noise factor

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

Determine the terrain sensitivity loss for a 4-GHz carrier that is propagating over a very dry, mountainous area. A. -1.25 dB B. -3.05 dB C. -2.01 dB D. -5.01 dB

Description : Determine the terrain sensitivity loss for a 4-GHz carrier that is propagating over a very dry, mountainous area. A. -1.25 dB B. -3.05 dB C. -2.01 dB D. -5.01 dB

Last Answer : A. -1.25 dB