Find the load impedance that must be used to terminate RG-62A/U to avoid reflections? A. 93Ω B. 75Ω C. 50Ω D. 300Ω

Find the load impedance that must be used to terminate RG-62A/U to avoid reflections?
A. 93Ω
B. 75Ω
C. 50Ω
D. 300Ω
by

1 Answer

Answer :

A. 93Ω
by

Related questions

What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Description : What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Last Answer : C. 50Ω

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Description : What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Last Answer : D. 301Ω

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Description : What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Last Answer : B.0.68

A single conductor running from the transmitter to the antenna. A. RG-8/U B. Single line wire C. Twin-lead D. MIcrostrip

Description : A single conductor running from the transmitter to the antenna. A. RG-8/U B. Single line wire C. Twin-lead D. MIcrostrip

Last Answer : B. Single line wire

What is the noise voltage across a 300Ω input resistance to a TV set with a 6MHz bandwidth and temperature of 30˚C? A. 2.3 µV B. 3.8µV C. 5.5µV D. 5.4µV

Description : What is the noise voltage across a 300Ω input resistance to a TV set with a 6MHz bandwidth and temperature of 30˚C? A. 2.3 µV B. 3.8µV C. 5.5µV D. 5.4µV

Last Answer : C. 5.5µV

A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient?

Description : A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9 

Last Answer : A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9 

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Last Answer : B. 0.66

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Last Answer : C. 0.66

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

The use of telecommunication for the transmission of signals to initiate, modify or terminate functions of equipment at a distance. A. Tracking B. space command C. Telecommand D. Trunking

Description : The use of telecommunication for the transmission of signals to initiate, modify or terminate functions of equipment at a distance. A. Tracking B. space command C. Telecommand D. Trunking

Last Answer : C. Telecommand

The use of telecommunication for the transmission of signals to initiate, modify or terminate functions of equipment at a distance. A. Tracking B. Telemetry C. Telecommand D. Space telemetry

Description : The use of telecommunication for the transmission of signals to initiate, modify or terminate functions of equipment at a distance. A. Tracking B. Telemetry C. Telecommand D. Space telemetry

Last Answer : C. Telecommand

The size, shape, and dielectric material of a waveguide must be constant throughout its length for energy to move from one end to the other without reflections. What could be the effect in any abrupt change in its size or shape?

Description : The size, shape, and dielectric material of a waveguide must be constant throughout its length for energy to move from one end to the other without reflections. What could be the effect in any abrupt change in its size or shape?

Last Answer : Reflections.

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Two transformers having the same p.u. impedance connected in parallel share the connected load

Description : Two transformers having the same p.u. impedance connected in parallel share the connected load (A) equally (B) in proportion to the respective ratings (C) in proportion to the voltage ratio (D) in proportion to the zero phase displacement

Last Answer : Two transformers having the same p.u. impedance connected in parallel share the connected load in proportion to the respective ratings

Output resistance of an actual op-amp is A. 45Ω B. 46Ω C. 70Ω D. 75Ω

Description : Output resistance of an actual op-amp is A. 45Ω B. 46Ω C. 70Ω D. 75Ω

Last Answer : 75Ω

The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Description : The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Last Answer : B. 300 Ω

A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Description : A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Last Answer : C. has a zero DC resistance to ground

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Description : Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Last Answer : C. quarter-wavelength transformer

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Description : What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Last Answer : D. 2500 Ω

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Description : What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Last Answer : C. Dielectrics in the line

What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Description : What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Last Answer : A. 300 ohms

What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Description : What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Last Answer : D. Radiation resistance plus ohmic resistance

A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Description : Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Last Answer : B. 120 ohms

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

What determines the velocity factor in transmission line? A. The center conductor resistivity B. Dielectrics in the line C. The termination impedance D. The line length

Description : What determines the velocity factor in transmission line? A. The center conductor resistivity B. Dielectrics in the line C. The termination impedance D. The line length

Last Answer : B. Dielectrics in the line

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

Which of the following is and impedance matching ration of coax balun? A. 2:8 B. 1:2 C. 4:1 D. 2:1

Description : Which of the following is and impedance matching ration of coax balun? A. 2:8 B. 1:2 C. 4:1 D. 2:1

Last Answer : C. 4:1

Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Description : Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Last Answer : B. Velocity factor

A convenient method of determining antenna impedance. A. Stub matching B. Reactance circle C. Smith chart D. Trial and error

Description : A convenient method of determining antenna impedance. A. Stub matching B. Reactance circle C. Smith chart D. Trial and error

Last Answer : C. Smith chart

What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Description : What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Last Answer : D. 75 Ω

What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Description : What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Last Answer : B. 156 Ω

What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Description : What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Last Answer : A. 100Ω

Why is input impedance of the FET very high?

Description : Why is input impedance of the FET very high?

Last Answer : BECAUSE its input circuit (gate to source) is reverse biased and input gate current is very small.

Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Last Answer : A. input

If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Description : If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Last Answer : C. infinite