An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a
minimum voltage of 17 V. Find the value of the resistive load.
A. 24.59Ω
B. Either A or C
C. 228.75Ω
D. Neither A nor C
by

1 Answer

Answer :

B. Either A or C
by

Related questions

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Last Answer : B. 0.66

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Last Answer : C. 0.66

Find the load impedance that must be used to terminate RG-62A/U to avoid reflections? A. 93Ω B. 75Ω C. 50Ω D. 300Ω

Description : Find the load impedance that must be used to terminate RG-62A/U to avoid reflections? A. 93Ω B. 75Ω C. 50Ω D. 300Ω

Last Answer : A. 93Ω

What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Description : What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Last Answer : C. 50Ω

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Description : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Last Answer : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be 4.

What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Description : What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Last Answer : A. Twisted pair

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3? A. 1.54 ns B. 11.5 ns C. 115.6 ns D. 1156 ns

Description : What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3? A. 1.54 ns B. 11.5 ns C. 115.6 ns D. 1156 ns

Last Answer : C. 115.6 ns

A single conductor running from the transmitter to the antenna. A. RG-8/U B. Single line wire C. Twin-lead D. MIcrostrip

Description : A single conductor running from the transmitter to the antenna. A. RG-8/U B. Single line wire C. Twin-lead D. MIcrostrip

Last Answer : B. Single line wire

Energy that has neither been radiated into space nor completely transmitted. A. Captured waves B. Incident waves C. Standing waves D. Modulated waves

Description : Energy that has neither been radiated into space nor completely transmitted. A. Captured waves B. Incident waves C. Standing waves D. Modulated waves

Last Answer : C. Standing waves

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

18 friends went to a restaurant for taking their breakfast. 17 of them spent RS.24 each on their breakfast and the last one spent RS.16 more then the average expenditure of all the 18. What was the total money spent by them? A) 228 B) 448.9 C) 458.6 D) 428.0

Description : 18 friends went to a restaurant for taking their breakfast. 17 of them spent RS.24 each on their breakfast and the last one spent RS.16 more then the average expenditure of all the 18. What was the total money spent by them? A) 228 B) 448.9 C) 458.6 D) 428.0 

Last Answer : B)  Let the average expenditure of all the 18 be Rs ‘x’.  Then (24 * 17) + (x + 16) = 18x 424 + x = 18x x = 24.9 therefore total money spent 18x  = 18 * 24.9  = Rs.448.9

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Description : Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Last Answer : B. 1.67

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Description : The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Last Answer : A. 1

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Description : At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Last Answer : D. Maximum voltage and minimum current.

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Description : What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Last Answer : D. Photovoltaic effect

What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Description : What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Last Answer : C. Quad

____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Description : ____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Last Answer : C. L carrier

A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Description : A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Last Answer : D. 1 watt

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Description : What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Last Answer : B.0.68

Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Description : Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Last Answer : A. N-type connector

Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Description : Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Last Answer : B. F-type connector

Which of the following coaxial cable connectors is called the UHF connector? A. PL-259 B. BNC C. N-type connector D. F connector

Description : Which of the following coaxial cable connectors is called the UHF connector? A. PL-259 B. BNC C. N-type connector D. F connector

Last Answer : A. PL-259

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite

To couple a coaxial line to parallel line, it is better to use a ______. A. Slotted line B. Quarter-wave transformer C. Directional Coupler D. Balun

Description : To couple a coaxial line to parallel line, it is better to use a ______. A. Slotted line B. Quarter-wave transformer C. Directional Coupler D. Balun

Last Answer : D. Balun

To connect coaxial line to a parallel-wire _________ is the best to use. A. directional coupler B. quarter-wave transformer C. balun D. slotted line

Description : To connect coaxial line to a parallel-wire _________ is the best to use. A. directional coupler B. quarter-wave transformer C. balun D. slotted line

Last Answer : C. balun

Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : A. power loss

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

In IEEE 802.11, _______ isan optionalaccess method that can be implemented inan infrastructure network (not in an ad hocnetwork). A) DCF B) PCF C) either (a) or (b) D) neither (a) nor (b)

Description : In IEEE 802.11, _______ isan optionalaccess method that can be implemented inan infrastructure network (not in an ad hocnetwork). A) DCF B) PCF C) either (a) or (b) D) neither (a) nor (b)

Last Answer : PCF

In IEEE 802.11, a BSS with an AP is sometimes referred toas ____________. A) an ad hocarchitecture B) an infrastructurenetworkC)either (a) or (b)D)neither (a) nor (b)

Description : In IEEE 802.11, a BSS with an AP is sometimes referred toas ____________. A) an ad hocarchitecture B) an infrastructurenetwork C) either (a) or (b) D) neither (a) nor (b)

Last Answer : an infrastructurenetwork

In IEEE 802.11, a BSS without an AP is called an _________. A) an ad hocarchitecture B) an infrastructurenetwork C) either (a) or (b) D) neither (a) nor (b)

Description : In IEEE 802.11, a BSS without an AP is called an _________. A) an ad hocarchitecture B) an infrastructurenetwork C) either (a) or (b) D) neither (a) nor (b)

Last Answer : an ad hocarchitecture

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

Electronic equipment used to measure standing wave ration. A. Reflectometer B. Wavemeter C. Altimeter D. Multimeter

Description : Electronic equipment used to measure standing wave ration. A. Reflectometer B. Wavemeter C. Altimeter D. Multimeter

Last Answer : A. Reflectometer

Surface preparation for Metallising the abrasives used for final cleaning is a) Chilled iron grit G.24, as defined in BS : 2451 b) Washed salt free angular silica sand of mesh size 12 to 30 with a minimum of 40% retained on a 20 mesh c) either (a) or (b) * d) d) neither (a) or (b)

Description : Surface preparation for Metallising the abrasives used for final cleaning is a) Chilled iron grit G.24, as defined in BS : 2451 b) Washed salt free angular silica sand of mesh size 12 to 30 with a minimum of 40% retained on a 20 mesh c) either (a) or (b) * d) d) neither (a) or (b)

Last Answer : c) either (a) or (b) *

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

In a transmission line, if the maximum current to minimum current ratio is 2:1 what is the ratio of the maximum voltage to minimum voltage? A. 4:1 B. 1:2 C. 1:4 D. 2:1

Description : In a transmission line, if the maximum current to minimum current ratio is 2:1 what is the ratio of the maximum voltage to minimum voltage? A. 4:1 B. 1:2 C. 1:4 D. 2:1

Last Answer : D. 2:1

Safe condition for storage of high V.M. bituminous coal is that (A) Height of the coal heap should be < 3 metres (B) Maximum 200 tons should be stored in a heap (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Safe condition for storage of high V.M. bituminous coal is that (A) Height of the coal heap should be < 3 metres (B) Maximum 200 tons should be stored in a heap (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)