A single conductor running from the transmitter to the antenna. A. RG-8/U B. Single line wire C. Twin-lead D. MIcrostrip

A single conductor running from the transmitter to the antenna.
A. RG-8/U
B. Single line wire
C. Twin-lead
D. MIcrostrip
by

1 Answer

Answer :

B. Single line wire
by

Related questions

What line has a typical velocity factor of about 0.8? A. Shielded pair B. Flexible coaxial C. Twin-lead D. Open-wire line

Description : What line has a typical velocity factor of about 0.8? A. Shielded pair B. Flexible coaxial C. Twin-lead D. Open-wire line

Last Answer : C. Twin-lead

The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Description : The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Last Answer : B. Closer coupling between the oscillator and the antenna.

Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Description : Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Last Answer : D. Flexible coaxial line

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

Find the load impedance that must be used to terminate RG-62A/U to avoid reflections? A. 93Ω B. 75Ω C. 50Ω D. 300Ω

Description : Find the load impedance that must be used to terminate RG-62A/U to avoid reflections? A. 93Ω B. 75Ω C. 50Ω D. 300Ω

Last Answer : A. 93Ω

What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Description : What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Last Answer : C. Quad

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Description : A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Last Answer : A. Antenna

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Description : Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Last Answer : B. 80,000 watts

A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Description : A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Last Answer : D. 8.36 kW

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Last Answer : B. 0.66

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Last Answer : C. 0.66

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

A dielectric waveguide for the propagation of electromagnetic energy at light frequencies a. Stripline b. Microstrip c. Laser beam d. Fiber optics

Description : A dielectric waveguide for the propagation of electromagnetic energy at light frequencies a. Stripline b. Microstrip c. Laser beam d. Fiber optics

Last Answer : d. Fiber optics

Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Description : Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Last Answer : C. quarter-wavelength transformer

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Description : Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Last Answer : D. both A and B

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

The antenna radiates _____ polarized waves when the transmitter antenna is horizontally installed. A. Vertically B. negatively C. horizontally D. circularly

Description : The antenna radiates _____ polarized waves when the transmitter antenna is horizontally installed. A. Vertically B. negatively C. horizontally D. circularly

Last Answer : C. horizontally

If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Description : If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Last Answer : B. 1000 times

In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Description : In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Last Answer : B. Dummy antenna

What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Description : What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Last Answer : A. 317 W

What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Description : What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Last Answer : C. 60 W

What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Description : What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Last Answer : B. 126 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Last Answer : A. 37.6 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Last Answer : C. 31.5 W

What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Last Answer : B. 39.7 W

The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

What is a dummy antenna? A. One which is used as a reference for gain measurements B. And antenna used for hand-held radio C. An non-directional transmitting antenna D. A non-radiating load for a transmitter used for testing

Description : What is a dummy antenna? A. One which is used as a reference for gain measurements B. And antenna used for hand-held radio C. An non-directional transmitting antenna D. A non-radiating load for a transmitter used for testing

Last Answer : D. A non-radiating load for a transmitter used for testing

What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Description : What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Last Answer : D. Efficiency = radiation resistance/total resistance x 100%

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Description : When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Last Answer : A. Dummy antenna

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

The most widely used antenna in GPS is (A) Parabolic antenna (B) Microstrip antenna (C) Horn antenna (D) Slotted antenna

Description : The most widely used antenna in GPS is (A) Parabolic antenna (B) Microstrip antenna (C) Horn antenna (D) Slotted antenna

Last Answer : Answer: Option B

Explain structure of rectangular microstrip patch antenna with its radiation pattern.

Description : Explain structure of rectangular microstrip patch antenna with its radiation pattern. 

Last Answer : In telecommunication, a microstrip antenna (also known as a printed antenna) usually means an antenna fabricated using microstrip techniques on a printed circuit board (PCB).It is a kind of ... microstrip transmission line with equivalent loads on either end to represent the radiation loss.