The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

The advantage of periscope antenna in microwave
A. Minimize interference to and from other neighboring stations
B. Shorten waveguide link
C. Reduce tower height
D. All of these
by

1 Answer

Answer :

B. Shorten waveguide link
by

Related questions

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Description : Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Last Answer : A. 0.871 μW

Propagation mode of microwave in a waveguide is known as _______. A. TM B. TE C. SW D. TEM

Description : Propagation mode of microwave in a waveguide is known as _______. A. TM B. TE C. SW D. TEM

Last Answer : B. TE

A radio communications link is to be established via the ionosphere. The maximum virtual height of the layer is 100 km at the midpoint of the path and the critical frequency is 2 MHz. The distance between stations is 600 km. determine the optimum working frequency? A. 6.32 MHz B. 2.1 MHz C. 5.4 MHz D. 1.8 MHz

Description : A radio communications link is to be established via the ionosphere. The maximum virtual height of the layer is 100 km at the midpoint of the path and the critical frequency is 2 MHz. The distance between stations is 600 ... optimum working frequency? A. 6.32 MHz B. 2.1 MHz C. 5.4 MHz D. 1.8 MHz

Last Answer : C. 5.4 MHz

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

What antenna can be used to minimize the effect of Faraday rotation of polarization? A. Dipole B. Parabolic C. Helical D. Rhombic

Description : What antenna can be used to minimize the effect of Faraday rotation of polarization? A. Dipole B. Parabolic C. Helical D. Rhombic

Last Answer : C. Helical

Best reason for pressurizing waveguides with dry air A. To maintain propagation B. To maintain temperature of the waveguide C. To reduce the possibility of internal arcing D. To increase the speed of propagation

Description : Best reason for pressurizing waveguides with dry air A. To maintain propagation B. To maintain temperature of the waveguide C. To reduce the possibility of internal arcing D. To increase the speed of propagation

Last Answer : C. To reduce the possibility of internal arcing

In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Description : In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Last Answer : B. Dummy antenna

When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Description : When testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Dummy antenna B. Hertzian antenna C. None of these D. Void antenna

Last Answer : A. Dummy antenna

Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Description : Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Last Answer : D. wave traps in the antenna circuitry

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

What is the estimated medium wind loading in the Philippines for antenna tower design? A. 300 kph B. 100 kph C. 200 kph D. 250 kph

Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 300 kph B. 100 kph C. 200 kph D. 250 kph

Last Answer : C. 200 kph

_____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Description : _____ is an antenna with a number of half-wave antenna on it. A. Antenna array B. Tower C. Omni-directional D. Rhombic

Last Answer : A. Antenna array

What is the estimated medium wind loading in the Philippines for antenna tower design? A. 200 kph B. 250 kph C. 300 kph D. 100 kph

Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 200 kph B. 250 kph C. 300 kph D. 100 kph

Last Answer : A. 200 kph

What illumination factor is normally considered in computing parabolic antenna gain in microwave communications? A. 0.54 B. 0.65 C. 0.75 D. 0.85

Description : What illumination factor is normally considered in computing parabolic antenna gain in microwave communications? A. 0.54 B. 0.65 C. 0.75 D. 0.85

Last Answer : A. 0.54

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

It is a measure of the microwave power radiated from an antenna as a function of angular direction from the antenna axis. A. Antenna pattern B. Polarization C. Beamwidth D. Sidelobes

Description : It is a measure of the microwave power radiated from an antenna as a function of angular direction from the antenna axis. A. Antenna pattern B. Polarization C. Beamwidth D. Sidelobes

Last Answer : C. Beamwidth

A means of beyond the line-of-sight propagation of microwave signal. A. Space wave B. Microwave link C. Troposcatter D. Point-to-point

Description : A means of beyond the line-of-sight propagation of microwave signal. A. Space wave B. Microwave link C. Troposcatter D. Point-to-point

Last Answer : C. Troposcatter

A microwave link between the earth station and the down-town terminal. A. STL B. Uplink C. Downlink D. Terrestrial link

Description : A microwave link between the earth station and the down-town terminal. A. STL B. Uplink C. Downlink D. Terrestrial link

Last Answer : D. Terrestrial link

The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Description : The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Last Answer : D. improved radiation efficiency

What is a selective fading effect? A. A fading effect caused by small changes in beam heading at the receiving station. B. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. C. A fading effect caused by large changes in the height of the ionosphere, as experienced at the receiving station D. A fading effect caused by time differences between the receiving and transmitting stations.

Description : What is a selective fading effect? A. A fading effect caused by small changes in beam heading at the receiving station. B. A fading effect caused by phase differences between radio wave ... station D. A fading effect caused by time differences between the receiving and transmitting stations.

Last Answer : B. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station.

What is the major cause of selective fading? A. Small changes in the beam heading at the receiving station. B. Large changes in the height of the ionosphere, as experience at the receiving station. C. Time differences between the receiving and transmitting stations. D. Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Description : What is the major cause of selective fading? A. Small changes in the beam heading at the receiving station. B. Large changes in the height of the ionosphere, as experience at the ... Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Last Answer : D. Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Refers to an effect of selective fading. A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. B. A fading effect caused by small changes in beam heading at the receiving station. C. A fading effect caused by the time differences between the receiving and transmitting stations. D. A fading effect caused by large changes in the height of the ionosphere, as experienced at the receiving station.

Description : Refers to an effect of selective fading. A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. B. A fading ... caused by large changes in the height of the ionosphere, as experienced at the receiving station.

Last Answer : A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station.

How would one squeeze more channels of communication into TDM frames of standard length? A. Shorten the time delay for each channel B. Raise the amplitude C. Add modulators D. Remove the synchronizing pulses

Description : How would one squeeze more channels of communication into TDM frames of standard length? A. Shorten the time delay for each channel B. Raise the amplitude C. Add modulators D. Remove the synchronizing pulses

Last Answer : A. Shorten the time delay for each channel

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

An ungrounded antenna near the ground A. acts as a single antenna of twice the height B. is unlikely to need an earth mat C. acts as antenna array D. must be horizontally polarized

Description : An ungrounded antenna near the ground A. acts as a single antenna of twice the height B. is unlikely to need an earth mat C. acts as antenna array D. must be horizontally polarized

Last Answer : C. acts as antenna array

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

Actual height of antenna should be at least A. one wavelength B. half wavelength C. quarter wavelength D. three-fourth wavelength

Description : Actual height of antenna should be at least A. one wavelength B. half wavelength C. quarter wavelength D. three-fourth wavelength

Last Answer : C. quarter wavelength

Top loading is used in an antenna in order to increase its ______. A. practical height B. beamwidth C. effective height D. input capacitance

Description : Top loading is used in an antenna in order to increase its ______. A. practical height B. beamwidth C. effective height D. input capacitance

Last Answer : C. effective height

For a space wave transmission, the radio horizon distance of a receiving antenna with a height of 64 meters is approximately A. 8 km B. 32 km C. 64 km D. 256 km

Description : For a space wave transmission, the radio horizon distance of a receiving antenna with a height of 64 meters is approximately A. 8 km B. 32 km C. 64 km D. 256 km

Last Answer : B. 32 km

The angle of elevation of the antenna beam is 20°. Calculate the transmission-path distance for an ionospheric transmission that utilizes a layer of virtual height 200 km. Use flat-earth approximation. A. 966 km B. 2100 km C. 1100 km D. 405 km

Description : The angle of elevation of the antenna beam is 20°. Calculate the transmission-path distance for an ionospheric transmission that utilizes a layer of virtual height 200 km. Use flat-earth approximation. A. 966 km B. 2100 km C. 1100 km D. 405 km

Last Answer : C. 1100 km

The antenna effective height is ____ to ____ of the actual height. A. ½ to 2/3 B. ½ to ¾ C. ¼ to 2/3 D. ¼ to ¾

Description : The antenna effective height is ____ to ____ of the actual height. A. ½ to 2/3 B. ½ to ¾ C. ¼ to 2/3 D. ¼ to ¾

Last Answer : A. ½ to 2/3

A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Description : A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Last Answer : A. 36 meters high

For a space wave transmission, the radio horizon distance of a transmitting antenna with a height of 100 meters is approximately:A. 10 km B. 40 km C. 100 km D. 400 km

Description : For a space wave transmission, the radio horizon distance of a transmitting antenna with a height of 100 meters is approximately: A. 10 km B. 40 km C. 100 km D. 400 km

Last Answer : B. 40 km

Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Description : Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Last Answer : D. effective height

What device can be constructed to allow microwave energy to pass in one direction but blocks energy in the other direction in a waveguide?

Description : What device can be constructed to allow microwave energy to pass in one direction but blocks energy in the other direction in a waveguide?

Last Answer : errite Isolato

A dielectric waveguide for the propagation of electromagnetic energy at light frequencies a. Stripline b. Microstrip c. Laser beam d. Fiber optics

Description : A dielectric waveguide for the propagation of electromagnetic energy at light frequencies a. Stripline b. Microstrip c. Laser beam d. Fiber optics

Last Answer : d. Fiber optics

Proposed the use of clad glass fiber as a dielectric waveguide a. Karpon and Keck b. Karpon and Bockham c. Bockham and Kao d. Kao and Keck

Description : Proposed the use of clad glass fiber as a dielectric waveguide a. Karpon and Keck b. Karpon and Bockham c. Bockham and Kao d. Kao and Keck

Last Answer : c. Bockham and Kao

Which of the following antennas is best excited from a waveguide? A. Biconical B. Horn C. Helical D. Discone

Description : Which of the following antennas is best excited from a waveguide? A. Biconical B. Horn C. Helical D. Discone

Last Answer : B. Horn

What device in a waveguide system used for stopping or diverting electromagnetic wave as desired? A. Mechanical switch B. Electric switch C. Push-button switch D. Waveguide switch

Description : What device in a waveguide system used for stopping or diverting electromagnetic wave as desired? A. Mechanical switch B. Electric switch C. Push-button switch D. Waveguide switch

Last Answer : D. Waveguide switch

A waveguide passive component that brings a smooth change in the direction of axis maintained perpendicular to the plane of polarization? A. L bend B. H bend C. T bend D. X bend

Description : A waveguide passive component that brings a smooth change in the direction of axis maintained perpendicular to the plane of polarization? A. L bend B. H bend C. T bend D. X bend

Last Answer : B. H bend

Which of the following is not a bounded medium? A. Coaxial line B. Two-wire line C. Waveguide D. Free space

Description : Which of the following is not a bounded medium? A. Coaxial line B. Two-wire line C. Waveguide D. Free space

Last Answer : D. Free space

When electromagnetic wave are propagated through a waveguide, they A. are reflected from the walls but do not travel along them B. travel along all four walls of the waveguide C. travel along the broader walls of the guide D. travel through the dielectric without touching the walls

Description : When electromagnetic wave are propagated through a waveguide, they A. are reflected from the walls but do not travel along them B. travel along all four walls of the waveguide C. travel along the broader walls of the guide D. travel through the dielectric without touching the walls

Last Answer : A. are reflected from the walls but do not travel along them

Proposed the use of a clad glass fiber as a dielectric waveguide. A. Kao and Keck B. Karpon and Keck C. Karpon and Bockham D. Bockham and Kao

Description : Proposed the use of a clad glass fiber as a dielectric waveguide. A. Kao and Keck B. Karpon and Keck C. Karpon and Bockham D. Bockham and Kao

Last Answer : D. Bockham and Kao

What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Description : What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Last Answer : D. No transmitter power is wasted in the carrier

How does a waveguide-type lens focus spherical wavefront microwave energy?

Description : How does a waveguide-type lens focus spherical wavefront microwave energy?

Last Answer : Some wavefronts are accelerated so that all wavefronts exit the lens at the same time

Waveguide are used mainly for microwave signals because

Last Answer : Waveguide are used mainly for microwave signals because They would be too bulky at lower frequencies.

A new railway line is required to be constructed beaus’ of following reasons (a) Strategic and political considerations (b) Development of backward area (c) To shorten existing rail link (d) Any of them*

Description : A new railway line is required to be constructed beaus’ of following reasons (a) Strategic and political considerations (b) Development of backward area (c) To shorten existing rail link (d) Any of them*

Last Answer : d) Any of them*

The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Description : The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Last Answer : c. Wider bandwidth