nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

nif stands for
A. Non-intrinsic figure
B. Noise improvement factor
C. Narrow intermediate frequency
D. Noise interference figure
by

1 Answer

Answer :

B. Noise improvement factor
by

Related questions

Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Description : Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Last Answer : C. Noise improvement factor

An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Description : An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Last Answer : D. 99.7 MHz

Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Last Answer : C. Out of the band

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

In cellular system, _____ defines the geographic distance that is required between cells using identical frequencies in order to avoid interference between the radio transmissions at these cells. A. frequency-reuse ratio B. distance-to-reuse ratio (D/R) C. reuse format plan ratio D. reuse factor

Description : In cellular system, _____ defines the geographic distance that is required between cells using identical frequencies in order to avoid interference between the radio transmissions at these cells. A. frequency-reuse ratio B. distance-to-reuse ratio (D/R) C. reuse format plan ratio D. reuse factor

Last Answer : B. distance-to-reuse ratio (D/R)

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Description : A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Last Answer : A. Noise equivalent power

Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Description : Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Last Answer : D. wave traps in the antenna circuitry

Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Description : Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Last Answer : A. Crosstalk

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : C. Impulse noise

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : A. Quantizing noise

Form of interference caused by rain or dust storms. A. Precipitation static B. Shot-noise C. Galactic noise D. Impulse noise

Description : Form of interference caused by rain or dust storms. A. Precipitation static B. Shot-noise C. Galactic noise D. Impulse noise

Last Answer : A. Precipitation static

_________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Description : _________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Last Answer : D. Noise

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Description : The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Last Answer : D. 300 – 3000 MHz

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Description : The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Last Answer : B. Noise

A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Description : A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Last Answer : B. 660 kHz

What is the most commonly used intermediate frequency of radar receivers? A. 40 MHz B. 60 MHz C. 70 MHz D. 30 MHz

Description : What is the most commonly used intermediate frequency of radar receivers? A. 40 MHz B. 60 MHz C. 70 MHz D. 30 MHz

Last Answer : D. 30 MHz

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Description : The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Last Answer : A. Noise density

The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Description : The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Last Answer : D. MESFET

Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Last Answer : A. 1.6 dB

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

One of the following is not a useful quantity for comparing the noise performance receivers. A. Input noise voltage B. Equivalent noise resistance C. Noise temperature D. Noise figure.

Description : One of the following is not a useful quantity for comparing the noise performance receivers. A. Input noise voltage B. Equivalent noise resistance C. Noise temperature D. Noise figure.

Last Answer : A. Input noise voltage

The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Description : The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Last Answer : C. 10.79 dB

ECE Board Exam March 1996 The equivalent noise temperature of the amplifier is 25 K. What is the noise figure? A. 1.86 B. 0.1086 C. 1.086 D. 10.86

Description : ECE Board Exam March 1996 The equivalent noise temperature of the amplifier is 25 K. What is the noise figure? A. 1.86 B. 0.1086 C. 1.086 D. 10.86

Last Answer : C. 1.086

Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Description : Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Last Answer : D. Miscellaneous noise

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Last Answer : B. Impulse noise voltage is dependent on bandwidth

Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Last Answer : C. 15 to 160 MHz

What is the reference frequency of CCIT phosphomeric noise measurement? A. 800 HzB. 1000 Hz C. 1500 Hz D. 3400 Hz

Description : What is the reference frequency of CCIT phosphomeric noise measurement? A. 800 Hz B. 1000 Hz C. 1500 Hz D. 3400 Hz

Last Answer : A. 800 Hz

Unwanted radio signal on assigned frequency. A. Splatter B. RFI C. Noise D. EMI

Description : Unwanted radio signal on assigned frequency. A. Splatter B. RFI C. Noise D. EMI

Last Answer : C. Noise

Noise from random acoustic or electric noise that has equal energy per cycle over a specified total frequency band. A. Gaussian noise B. Whiter noise C. Thermal noise D. All of the above

Description : Noise from random acoustic or electric noise that has equal energy per cycle over a specified total frequency band. A. Gaussian noise B. Whiter noise C. Thermal noise D. All of the above

Last Answer : D. All of the above

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

One of the following is not among the advantages of series modulation A. No transformer B. Suppressed white noise C. Simple.D. Modulates any frequency

Description : One of the following is not among the advantages of series modulation A. No transformer B. Suppressed white noise C. Simple D. Modulates any frequency

Last Answer : B. Suppressed white noise

What is the reference frequency of CCITT psophometric noise measurement? A. 800 Hz B. 1500 Hz C. 3400 Hz D. 1000 Hz

Description : What is the reference frequency of CCITT psophometric noise measurement? A. 800 Hz B. 1500 Hz C. 3400 Hz D. 1000 Hz

Last Answer : A. 800 Hz

Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Description : Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Last Answer : B. 15 to 160 Mhz

Noise from random acoustic or electric noise that has equal per cycle over a specified total frequency band. A. Thermal noise B. White noise C. Gaussian noise D. All of these

Description : Noise from random acoustic or electric noise that has equal per cycle over a specified total frequency band. A. Thermal noise B. White noise C. Gaussian noise D. All of these

Last Answer : D. All of these

One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Description : One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Last Answer : A. noise is amplified with voice when an FDM system is used

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Description : What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Last Answer : B. Noise factor

What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Description : What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Last Answer : A. 1.09

The difference between the original and reconstructed signal gives rise to A. S factor B. Quantizing noise C. S/N D. Fade margin

Description : The difference between the original and reconstructed signal gives rise to A. S factor B. Quantizing noise C. S/N D. Fade margin

Last Answer : B. Quantizing noise

Differentiate between intrinsic and extrinsic semiconductor

Description : Differentiate between intrinsic and extrinsic semiconductor

Last Answer : Pure form of semiconductors are said to be intrinsic semiconductor. Ex: germanium, silicon. It has poor conductivity If certain amount of impurity atom is added to intrinsic semiconductor the resulting semiconductor is Extrinsic or impure Semiconductor It has good conductivity.

It is the made from semiconductor material such as aluminum-galium-arsenide or gallium-arsenide-phosphide. A. APD B. Injection laser diode C. Light emitting diode D. Positive-intrinsic-negative

Description : It is the made from semiconductor material such as aluminum-galium-arsenide or gallium-arsenide-phosphide. A. APD B. Injection laser diode C. Light emitting diode D. Positive-intrinsic-negative

Last Answer : C. Light emitting diode