What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

What do you call the single booster installed on the antenna dish of satellite receiver?
A. Low noise amplifier
B. Single amplifier
C. Noise amplifier
D. Rectifier
by

1 Answer

Answer :

A. Low noise amplifier
by

Related questions

_________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Description : _________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Last Answer : B. LNA

Collects very weak signal from a broadcast satellite A. Satellite dish B. LNB C. Yagi-Uda antenna D. Satellite receiver

Description : Collects very weak signal from a broadcast satellite A. Satellite dish B. LNB C. Yagi-Uda antenna D. Satellite receiver

Last Answer : A. Satellite dish

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Feedhorn B. Satellite dish C. Satellite receiver D. LNB

Description : _______ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Feedhorn B. Satellite dish C. Satellite receiver D. LNB

Last Answer : D. LNB

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Description : Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Last Answer : D. Mixer

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Description : Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Last Answer : D. Mixer

Collects very weak signals from a broadcast satellite A. Helical antenna B. Satellite dish C. LNA D. TWT

Description : Collects very weak signals from a broadcast satellite A. Helical antenna B. Satellite dish C. LNA D. TWT

Last Answer : B. Satellite dish

In shipboard satellite dish antennas system, azimuth is referred as the _______. A. 0 to 90 degrees B. Vertical aiming of the antenna C. North to East D. Horizontal aiming of the antenna

Description : In shipboard satellite dish antennas system, azimuth is referred as the _______. A. 0 to 90 degrees B. Vertical aiming of the antenna C. North to East D. Horizontal aiming of the antenna

Last Answer : D. Horizontal aiming of the antenna

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Description : What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Last Answer : A. Gain-to-Equivalent Noise Temperature Ratio (G/Te)

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

An antenna with very high gain and very narrow beamwidth. A. Helical antenna B. Discone antenna C. Horn antenna D. Parabolic dish antenna

Description : An antenna with very high gain and very narrow beamwidth. A. Helical antenna B. Discone antenna C. Horn antenna D. Parabolic dish antenna

Last Answer : D. Parabolic dish antenna

How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Description : How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Last Answer : C. Gain increases 6 dB

What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Description : What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Last Answer : C. Video detector

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

The antenna radiates _____ polarized waves when the transmitter antenna is horizontally installed. A. Vertically B. negatively C. horizontally D. circularly

Description : The antenna radiates _____ polarized waves when the transmitter antenna is horizontally installed. A. Vertically B. negatively C. horizontally D. circularly

Last Answer : C. horizontally

A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Description : A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Last Answer : A. 36 meters high

What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi

Description : What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi

Last Answer : B.25mi

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Last Answer : A. 1.6 dB

Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Description : Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Last Answer : A. microvolts

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Description : What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Last Answer : B. The combination of two signals to produce sum and difference frequencies.

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

The signal path from satellite to earth-based receiver. A. Downlink signal B. Uplink signal C. Incident signal D. Reflected signal

Description : The signal path from satellite to earth-based receiver. A. Downlink signal B. Uplink signal C. Incident signal D. Reflected signal

Last Answer : A. Downlink signal

What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Description : What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Last Answer : A. 0.5 s

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

Which of the following is the basic component of a communications satellite receiver? A. On-board computer B. Reflector C. Telemetry D. Transponder

Description : Which of the following is the basic component of a communications satellite receiver? A. On-board computer B. Reflector C. Telemetry D. Transponder

Last Answer : D. Transponder

Receives and collects satellite signals form a broadcast satellite. A. LNB B. Yagi-Uda array C. Satellite receiver D. Satellite disk

Description : Receives and collects satellite signals form a broadcast satellite. A. LNB B. Yagi-Uda array C. Satellite receiver D. Satellite disk

Last Answer : D. Satellite disk

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite