How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

How can receiver desensitizing be reduced?
A. Increase the receiver bandwidth
B. Ensure good RF shielding between the transmitter and receiver
C. Increase the transmitter audio gain
D. Decrease the receiver squelch, gain.
by

1 Answer

Answer :

D. Decrease the receiver squelch, gain.
by

Related questions

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Description : ECE Board Exam March 1996 The capture area of an antenna is directly proportional to the A. frequency of the received signal B. distance between transmitter and receiver C. gain of the antenna D. power density of the signal

Last Answer : C. gain of the antenna

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Description : A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Last Answer : D. FDMA

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Description : When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Last Answer : D. 150 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Description : Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Last Answer : D. detector stage

Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Last Answer : A. RF carrier

Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Description : Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Last Answer : D. wave traps in the antenna circuitry

What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Description : What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Last Answer : D. No transmitter power is wasted in the carrier

What is shielding in NMR? A. Using a curved piece of metal to block an opponent’s attack B. Putting metal around an Rf source C. When the magnetic moment of an atom blocks the full induced magnetic field from surrounding nuclei D. Blocking parts of a molecule from Rf radiation

Description : What is shielding in NMR? A. Using a curved piece of metal to block an opponent’s attack B. Putting metal around an Rf source C. When the magnetic moment of an atom blocks the full induced magnetic field from surrounding nuclei D. Blocking parts of a molecule from Rf radiation

Last Answer : When the magnetic moment of an atom blocks the full induced magnetic field from surrounding nuclei

Width of frequency band just enough to ensure the transmission of information at a required rate and quality required, and under a specified condition and class of emission. A. Occupied bandwidth B. Transmission bandwidth C. Necessary bandwidth D. Frequency bandwidth

Description : Width of frequency band just enough to ensure the transmission of information at a required rate and quality required, and under a specified condition and class of emission. A. Occupied bandwidth B. Transmission bandwidth C. Necessary bandwidth D. Frequency bandwidth

Last Answer : C. Necessary bandwidth

The width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under a specified condition and class of emission. A. Occupied bandwidth B. Reference frequency C. Necessary bandwidth D. Frequency tolerance bandwidth

Description : The width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under a specified condition and class of emission. A. Occupied bandwidth B. Reference frequency C. Necessary bandwidth D. Frequency tolerance bandwidth

Last Answer : C. Necessary bandwidth

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Description : What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Last Answer : A. 0.5 s

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

Which of the following is not one of the natural ways a radio wave may travel from transmitter to receiver? A. Ground wave B. Micro wave C. Sky wave D. Space wave

Description : Which of the following is not one of the natural ways a radio wave may travel from transmitter to receiver? A. Ground wave B. Micro wave C. Sky wave D. Space wave

Last Answer : B. Micro wave

What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Description : What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Last Answer : A. 6.065 GHz

What is the path attenuation between transmitter and receiver at a frequency of 1.2 Ghz and a distance of 11,000 mi? A. 119 dB B. 115dB C. 179dB D. 174dB

Description : What is the path attenuation between transmitter and receiver at a frequency of 1.2 Ghz and a distance of 11,000 mi? A. 119 dB B. 115dB C. 179dB D. 174dB

Last Answer : C. 179dB

What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Description : What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Last Answer : D. Optic regenerators

Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Description : Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Last Answer : B. The transmitter and receiver

Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Description : Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Last Answer : C. Transmitter, channel and receiver

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Description : Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Last Answer : B. narrowing the bandwidth

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Description : DME and VOR are “frequency paired” because: a. The same receiver can be used for both aids b. The VOR transmitter is easily converted to the required DME frequency c. Cockpit workload is reduced d. Both ground transmitter aerials can be placed on the same site if required

Last Answer : c. Cockpit workload is reduced

______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Description : ______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Last Answer : C. Beamwidth

If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Description : If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Last Answer : B. 1000 times