For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

For a shortened vertical antenna, where should a loading coil be placed to minimize losses
and produce the most effective performance?
A. As low as possible on the vertical radiator
B. Near the center of the vertical radiator
C. As close to the transmitter as possible
D. At a voltage node
by

1 Answer

Answer :

B. Near the center of the vertical radiator
by

Related questions

The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Description : The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Last Answer : D. improved radiation efficiency

Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Description : Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Last Answer : D. loading coil

Where the voltage node of a half-wave antenna does exists? A. At feed point B. Near the center C. At center D. Near the feed point

Description : Where the voltage node of a half-wave antenna does exists? A. At feed point B. Near the center C. At center D. Near the feed point

Last Answer : A. At feed point

The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Description : What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Last Answer : A. It is increased

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

Top loading is used in an antenna in order to increase its ______. A. practical height B. beamwidth C. effective height D. input capacitance

Description : Top loading is used in an antenna in order to increase its ______. A. practical height B. beamwidth C. effective height D. input capacitance

Last Answer : C. effective height

Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Description : Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Last Answer : D. effective height

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%

What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Description : What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Last Answer : A. 317 W

What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Description : What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Last Answer : C. 60 W

What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Description : What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Last Answer : B. 126 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Last Answer : A. 37.6 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Last Answer : C. 31.5 W

What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Last Answer : B. 39.7 W

Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Description : Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Last Answer : B. 80,000 watts

What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Description : What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Last Answer : D. Efficiency = radiation resistance/total resistance x 100%

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

In horizontal-dipole antenna, the polarization is A. in the vertical direction B. in the horizontal direction C. circular D. measured at the center of the antenna

Description : In horizontal-dipole antenna, the polarization is A. in the vertical direction B. in the horizontal direction C. circular D. measured at the center of the antenna

Last Answer : B. in the horizontal direction

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Description : What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Last Answer : C. 3.9 dB

A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Description : A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Last Answer : B. Isotropic radiator

An isotropic radiator is A. in the northern hemisphere B. an antenna high enough in the air C. an antenna whose directive pattern is substantially incredible D. a hypothetical, omnidirectional antenna

Description : An isotropic radiator is A. in the northern hemisphere B. an antenna high enough in the air C. an antenna whose directive pattern is substantially incredible D. a hypothetical, omnidirectional antenna

Last Answer : D. a hypothetical, omnidirectional antenna

What antenna can be used to minimize the effect of Faraday rotation of polarization? A. Dipole B. Parabolic C. Helical D. Rhombic

Description : What antenna can be used to minimize the effect of Faraday rotation of polarization? A. Dipole B. Parabolic C. Helical D. Rhombic

Last Answer : C. Helical

The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Description : The advantage of periscope antenna in microwave A. Minimize interference to and from other neighboring stations B. Shorten waveguide link C. Reduce tower height D. All of these

Last Answer : B. Shorten waveguide link

iv) A rectangular coil free to rotate is placed in uniform magnetic field with its plane parallel to the magnetic lines of force. Then the coil willa) rotate to maximize the magnetic flux through its plane. b)rotate to minimize the magnetic flux through its plane.c) not experience any torque since the magnetic flux through its plane is zero.d) experience the constant torque equal to NBIA

Description : iv) A rectangular coil free to rotate is placed in uniform magnetic field with its plane parallel to the magnetic lines of force. Then the coil willa) rotate to maximize the magnetic flux through ... since the magnetic flux through its plane is zero.d) experience the constant torque equal to NBIA

Last Answer : iv) A rectangular coil free to rotate is placed in uniform magnetic field with its plane parallel ... d) experience the constant torque equal to NBIA

One of the following makes an antenna physically long but electrically short A. Adding L in series B. Adding C in series C. Top loading D. Both A and C

Description : One of the following makes an antenna physically long but electrically short A. Adding L in series B. Adding C in series C. Top loading D. Both A and C

Last Answer : B. Adding C in series

What is the estimated medium wind loading in the Philippines for antenna tower design? A. 300 kph B. 100 kph C. 200 kph D. 250 kph

Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 300 kph B. 100 kph C. 200 kph D. 250 kph

Last Answer : C. 200 kph

When speaking of antennas. ______ is a section which would be a complete antenna by itself. A. image B. top loading C. bay D. quarterwave

Description : When speaking of antennas. ______ is a section which would be a complete antenna by itself. A. image B. top loading C. bay D. quarterwave

Last Answer : C. bay

What makes an antenna physically long but electrically short? A. Top loading B. Adding C in series C. Adding L in series D. All of these

Description : What makes an antenna physically long but electrically short? A. Top loading B. Adding C in series C. Adding L in series D. All of these

Last Answer : B. Adding C in series

What is the estimated medium wind loading in the Philippines for antenna tower design? A. 200 kph B. 250 kph C. 300 kph D. 100 kph

Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 200 kph B. 250 kph C. 300 kph D. 100 kph

Last Answer : A. 200 kph

Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Description : Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Last Answer : D. both A and B

The antenna radiates _____ polarized waves when the transmitter antenna is horizontally installed. A. Vertically B. negatively C. horizontally D. circularly

Description : The antenna radiates _____ polarized waves when the transmitter antenna is horizontally installed. A. Vertically B. negatively C. horizontally D. circularly

Last Answer : C. horizontally

If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Description : If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Last Answer : B. 1000 times

In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Description : In testing transmitter to prevent interfering with other stations, which type of antenna must be used? A. Void antenna B. Dummy antenna C. Hertzian antenna D. Isotropic antenna

Last Answer : B. Dummy antenna

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Description : The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Last Answer : B. Closer coupling between the oscillator and the antenna.

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Description : A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Last Answer : D. 8.36 kW