Description : Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours
Last Answer : Answer: D
Description : The state of charge of a lead acid storage battery is best indicated by the _____________. A. testing of the individual cell voltages B. ampere hour capacity of the battery C. specific gravity of the electrolyte D. total cell voltages
Last Answer : Answer: C
Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts
Last Answer : Answer: A
Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt
Description : Ampere hour capacity of an industrial battery is based on ……….hours discharge rate A. 8 B. 12 C. 16 D. 24
Last Answer : A. 8
Description : A capacitor of capacitance 50 micro farads is charged to a potential difference of 200 Volts. Find out energy stored in the condenser?
Last Answer : A capacitor of capacitance 50 micro farads is charged to a potential difference of 200 Volts. Find out energy stored in the condenser? 1 joule
Description : The state of charge of a lead-acid battery is best indicated by the ____________. A. individual cell voltage B. ampere-hour capacity C. electrolyte specific gravity D. total cell voltage
Description : Which of the listed battery charging circuits is used to maintain a wet-cell, lead-acid, storage battery in a fully charged state during long periods of disuse? A. Normal charging circuit B. Quick charging circuit C. Trickle charging circuit D. High ampere charging circuit
Description : A lead-acid battery can deliver 20 amperes continuously for 10 hours with an ampere-hour rating of ____________. A. 20 B. 40 C. 200 D. 400
Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm
Last Answer : d) 2.0 kJ/mm
Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts
Description : When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation
Description : From the standpoint of safety, you should never allow salt water to enter a leadacid storage battery or come in contact with sulfuric acid because ______________. A. the resulting gas is ... peroxide D. combining salt water with lead-acid creates an invisible gas resulting in severe corrosion
Last Answer : Answer: B
Description : When mixing electrolyte for a lead-acid storage battery, ______________. A. stirring should always be avoided B. a lead container should always be used C. always pour the water into the acid D. always pour the acid into the water
Description : A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a ... cells reaches the correct value and no longer increases over a period of 1 to 4 hours
Description : When using a charger to charge a ATV battery what settings should my charger be on 2 or 6 Amps 6 or 12 volts?
Last Answer : Set the charger on 2 amps and 12 volts. Hopefully you have anauto off charger that will not overcharge the battery. If not thencharge the battery for 6 hours and then with a digital volt metercheck ... is 50% charged. 12 volts and it is 25% charged. Chargeadditional hours to reach a full charge.
Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days
Description : Power transformers are rated in _____________. A. kilowatts B. ampere-turns C. kilowatt-volts D. kilovolt-amperes
Description : A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms
Description : If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps
Description : An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts
Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw
Description : A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms
Description : A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw
Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW
Description : Electrical power is expressed in _____________. A. ohms B. volts C. amps D. watts
Description : Fuses are usually rated in _____________. A. watts B. amps only C. volts only D. amps and volts
Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps
Description : How much current will flow in the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 amps B. 6 amps C. 8 amps D. 10 amps
Description : Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater ... voltage expected in the circuit in order to prevent damage from an off-scale reading.
Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW
Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts
Description : If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI
Description : A 10 volt battery connected to a capacitor delivers a charge of 0.5 coulombs. The capacitance of the capacitor is: w) 2 x 10-2 farads x) 5 x 10-2 farads y) 2 farads z) 5 farads
Last Answer : ANSWER: X -- 5 x 10-2 FARADS
Description : The capacity of a battery is expressed in terms of A. Current rating B. Voltage rating C. Ampere hour rating D. None of the above
Last Answer : C. Ampere hour rating
Description : The capacity of a battery is expressed in terms of A ampere per hour B current C volt D ampere
Last Answer : A ampere per hour
Description : If the capacity of a battery is 2800 mAh, it can supply 1.4 Ampere current for
Last Answer : If the capacity of a battery is 2800 mAh, it can supply 1.4 Ampere current for 120 minutes
Description : AC circuits develop resistance, inductance, and capacitance. The inductive reactance of a circuit is expressed in _____________. A. ohms B. mhos C. henrys D. farads
Description : Alternating current circuits develop resistance, inductance, and capacitance. The capacitance of individual capacitors is expressed in _____________. A. ohms B. mhos C. henrys D. farads
Description : Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________. A. ohms B. mhos C. henrys D. farads
Description : AC circuits possess characteristics of resistance, inductance, and capacitance. The capacitive reactance of a circuit is expressed in _____________. A. ohms B. mhos C. henrys D. farads
Description : V=100Sin (1000t+46 deg), I=2Sin (1000t+80 deg) what are the elements in the circuit a) R=30 ohm, L=30 mH b) R=30 ohm, C=33.3 micro farads c) R=40 ohm, L=30 mH d) R=40 ohm, L=33.3 micro farads
Last Answer : Ans: R=40 ohm, L=33.3 micro farads
Description : ______________ is one of the heterogeneous benefits of storage virtualization. A. Data migration. B. Scalable. C. Effective use of capacity. D. Lower total cost of ownership.
Last Answer : Data migration.
Description : In accordance with Coast Guard Regulations (46 CFR), each battery operated relay-controlled lantern must _____________. A. be readily portable B. contain a dry cell battery having a minimum capacity of ... automatic battery charger to maintain the battery in a fully charged state D. all of the above
Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.
Description : Electric current is the flow of electrons through a conductor; the rate of this flow is measured in ___________. A. volts B. amperes C. coulombs D. ohms
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts
Description : The inductance of a coil is measured in _____________. A. ohms B. volts C. henries D. amperes
Description : Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt
Description : What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to ... . Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.