A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a  basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using  DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy?  
a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm  c) 1.87 kJ/mm d) 2.0 kJ/mm
by

1 Answer

Answer :

d) 2.0 kJ/mm
by

Related questions

When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Description : When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Last Answer : b) Higher deposition rate

Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code calls for a 4t bend. Which of the following rollers should be selected for the testing? a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter

Description : Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code calls for a 4t bend. Which of the following rollers should be selected for the testing? a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter

Last Answer : d) 32mm diameter

Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Description : Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Last Answer : (B) Prevent electrode from contamination

What information should be recorded as a minimum, on a completed production weld? a) Size and type of electrode and b) Welding supervisor’s name c) Welder’s Identification, date and weld number d) Welding inspectors name

Description : What information should be recorded as a minimum, on a completed production weld? a) Size and type of electrode and b) Welding supervisor’s name c) Welder’s Identification, date and weld number d) Welding inspectors name

Last Answer : c) Welder’s Identification, date and weld number

A T-section beam having flange 180mm wide and 20 mm thick and web 150 mm long and 20 mm thick carries a udl of 80 kN/m over an effective span of 8 m. Calculate the maximum bending stress.

Description : A T-section beam having flange 180mm wide and 20 mm thick and web 150 mm long and 20 mm thick carries a udl of 80 kN/m over an effective span of 8 m. Calculate the maximum bending stress.

Last Answer : Solution :

Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded) (C) In spot welding, two pieces to be joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Last Answer : (D) Mild steel sheet cannot be spot welded

Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Description : Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Last Answer : (A) Electrode size

The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Description : The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Last Answer : (3) 200 to 250 V

When using multiple SAW arc systems (twin wires etc), the arcs often have different polarities or use all AC rather than DC polarity, this is to? a) Prevent arc blow between arcs b) To maximize productivity c) To even out the power factor on the mains supply d) Make it easier to initiate the arc

Description : When using multiple SAW arc systems (twin wires etc), the arcs often have different polarities or use all AC rather than DC polarity, this is to? a) Prevent arc blow between arcs b) To maximize productivity c) To even out the power factor on the mains supply d) Make it easier to initiate the arc

Last Answer : a) Prevent arc blow between arcs

Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Description : Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Last Answer : (B) Martensite formation

If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Last Answer : Answer: A

What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant information c) None if the tensile strength of the consumables is the same as the approved one d) Change the electrode for the correct type and continue welding

Description : What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant ... the same as the approved one d) Change the electrode for the correct type and continue welding

Last Answer : b) Report the incident and record all relevant information

In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Description : In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Last Answer : (i) +0.5mm, -0 mm in vertical *

Label size of foreign article is min & postage paid words should not be less than a) 70mm X 100mm & 300sq mm b) 50mm X 80mm & 200sq mmc) 25mm X 50 mm & 100 sq mm d) None of these

Description : Label size of foreign article is min & postage paid words should not be less than a) 70mm X 100mm & 300sq mm b) 50mm X 80mm & 200sq mm c) 25mm X 50 mm & 100 sq mm d) None of these

Last Answer : a) 70mm X 100mm & 300sq mm

It is desired to concentrate a 20% salt solution (20 kg of salt in 100 kg of solution) to a 30% salt solution in an evaporator. Consider a feed of 300 kg/min at 30°C. The boiling point of the solution is 110°C, the latent heat of vaporisation is 2100 kJ/kg and the specific heat of the solution is 4 kJ/kg.K. The rate at which the heat has to be supplied in (kJ/min) to the evaporator is (A) 3.06 × 10 5 (B) 6.12 × 10 5 (C) 7.24 × 10 5 (D) 9.08 × 10

Description : It is desired to concentrate a 20% salt solution (20 kg of salt in 100 kg of solution) to a 30% salt solution in an evaporator. Consider a feed of 300 kg/min at 30°C. The boiling point of the solution is 110°C, the latent heat of ... 3.06 10 5 (B) 6.12 10 5 (C) 7.24 10 5 (D) 9.08 10

Last Answer : (A) 3.06 × 10

A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Last Answer : Answer: A

What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Description : What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Last Answer : c) 10-12V

Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Description : Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Last Answer : (D) 40

A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale reading is 5 mm and zero of circular

Description : A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale reading is 5 mm and zero of circular

Last Answer : A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale ... (C) 0.053 cm (D) 0.529 cm

A 300mm diameter pipe, 5mm wall thickness is to be radiographed using the double wall single image technique. The source to be used is Iridium. Which of the following statements is true? a) It should not be done because the thickness is below that recommended b) It should be better to use a cobalt 60 source in this instance c) There is no problem with the technique d) Only the double wall, double image technique should be used with Iridium

Description : A 300mm diameter pipe, 5mm wall thickness is to be radiographed using the double wall single image technique. The source to be used is Iridium. Which of the following statements is true? a) ... problem with the technique d) Only the double wall, double image technique should be used with Iridium

Last Answer : c) There is no problem with the technique

Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department

Description : Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department

Last Answer : a) The welder and the welding inspector

Q-9 how many electrodes are used in the TANDEM SAW? What is the polarity of the both electrode?

Description : Q-9 how many electrodes are used in the TANDEM SAW? What is the polarity of the both electrode?

Last Answer : In TANDEM SAW process there are more than one electrode is used. But for first electrode alternative current and for second electrode direct current shall be used.

A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Last Answer : b. 3.14 mm

belt of silk runs over two metal pulleys, one of which is surrounded by a hollow metal sphere. Two electrodes, in the form of comb-shaped rows of sharp metal points, are positioned respectively near to the bottom of the lower pulley and inside the sphere, over the upper pulley. The top electrode is connected to the sphere and the bottom one to the ground. A high DC potential is applied to the upper pulley. A simple version of which equipment is being described here?

Description : belt of silk runs over two metal pulleys, one of which is surrounded by a hollow metal sphere. Two electrodes, in the form of comb-shaped rows of sharp metal points, are positioned ... potential is applied to the upper pulley. A simple version of which equipment is being described here?

Last Answer : Van de Graaff generator.

The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Description : The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Last Answer : a) 250 x 150mm*.

What would be the most likely SAW flux type for welding medium carbon steel which requires impact testing: a) Cellulosic b) Rutile c) Fused d) Agglomerated

Description : What would be the most likely SAW flux type for welding medium carbon steel which requires impact testing: a) Cellulosic b) Rutile c) Fused d) Agglomerated

Last Answer : d) Agglomerated

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Last Answer : b) 24.9mm

Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps

Description : Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps

Last Answer : a) MAG (GMAW)

Material of construction of the electrode used in the electric resistance welding is (A) Stainless steel (B) Graphite (C) Copper (D) Steel

Description : Material of construction of the electrode used in the electric resistance welding is (A) Stainless steel (B) Graphite (C) Copper (D) Steel

Last Answer : Option C

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

The type of dc generator used for arc welding purposes is a

Last Answer : The type of dc generator used for arc welding purposes is a Differentially compound generator.

The capacity of a storage battery is measured in ______________. A. volts B. ampere-hours C. farads D. amps

Description : The capacity of a storage battery is measured in ______________. A. volts B. ampere-hours C. farads D. amps

Last Answer : Answer: B

Stainless steel is welded using (A) Oxy-acetylene flame (B) Oxy-hydrogen flame (C) Arc welding (D) Inert gas arc welding

Description : Stainless steel is welded using (A) Oxy-acetylene flame (B) Oxy-hydrogen flame (C) Arc welding (D) Inert gas arc welding

Last Answer : (D) Inert gas arc welding

If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Description : If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Last Answer : Answer: C

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

A jet of water discharging from a 40 mm diameter orifice has a diameter of 32 mm at its vena contracta. The coefficient of contraction is (A) 0.46 (B) 0.64 (C) 0.78 (D) 0.87

Description : A jet of water discharging from a 40 mm diameter orifice has a diameter of 32 mm at its vena contracta. The coefficient of contraction is (A) 0.46 (B) 0.64 (C) 0.78 (D) 0.87

Last Answer : Answer: Option B

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

Which of the following generators is used for DC arc welding application ?

Description :  Which of the following generators is used for DC arc welding application ? (A) Series generator (B) Shunt generator (C) Differential compound generator (D) Over -compound generator

Last Answer : A

In how many time final grinding should be done of new AT weld ? (i) Just after the welding (ii) After 8 hrs of welding (iii) With in 24 hrs* (iv) None of the above

Description : In how many time final grinding should be done of new AT weld ? (i) Just after the welding (ii) After 8 hrs of welding (iii) With in 24 hrs* (iv) None of the above

Last Answer : iii) With in 24 hrs*

In how many time rough riding should be done of new AT weld ? (i) Just after the welding* (ii) After 8 hrs of welding (iii) After 24 hrs (iv) None of the above

Description : In how many time rough riding should be done of new AT weld ? (i) Just after the welding* (ii) After 8 hrs of welding (iii) After 24 hrs (iv) None of the above

Last Answer : i) Just after the welding*

A transport company is running five buses between two towns, which are 50 kms apart. Seating capacity of each bus is 50 passengers. Actually passengers carried by each bus were 75% of seating capacity. All buses ran on all days of the month. Each bus made one round trip per day. Passenger kms are: (a) 2,81,250 (b) 1,87,500 (c) 5,62,500 (d) None of the above

Description : A transport company is running five buses between two towns, which are 50 kms apart. Seating capacity of each bus is 50 passengers. Actually passengers carried by each bus were 75% of seating capacity. All buses ran on all days of ... (a) 2,81,250 (b) 1,87,500 (c) 5,62,500 (d) None of the above

Last Answer : (c) 5,62,500

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. Specific heat of block material is 0.4 kJ.kg-1. K-1. Ignoring the effect of expansion and contraction and also the heat capacity to tank, the total entropy change in kJ.kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Description : A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. ... .kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Last Answer : (B) 0

Steam is throttled to 0.1 MPa with 20 degrees of superheat. (a) What is the quality of throttled steam if its pressure is 0.75 MPa (b) What is the enthalpy of the process?  a) 97.6%,2713 kJ/kg  b) -97.6%, 2713 kJ/kg  c) 87.6%,3713 kJ/kg  d) -87.6%, 3713 kJ/kg

Description : Steam is throttled to 0.1 MPa with 20 degrees of superheat. (a) What is the quality of throttled steam if its pressure is 0.75 MPa (b) What is the enthalpy of the process?  a) 97.6%,2713 kJ/kg  b) -97.6%, 2713 kJ/kg  c) 87.6%,3713 kJ/kg  d) -87.6%, 3713 kJ/kg

Last Answer : 97.6%,2713 kJ/kg

The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider

Description : The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider

Last Answer : d) The weld width would be wider

t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved qualification to cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Description : t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved ... cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Last Answer : a) Never

What does the term WPQR means? a) Weld productivity quality review b) Weld production quality requirments c) Welding procedure

Description : What does the term WPQR means? a) Weld productivity quality review b) Weld production quality requirments c) Welding procedure

Last Answer : c) Welding procedure