The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load

The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load
by

1 Answer

Answer :

Answer: B
by

Related questions

The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest load C. the sum of the powers used in each individual load D. never more than the power used in the largest load

Description : The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest ... of the powers used in each individual load D. never more than the power used in the largest load

Last Answer : Answer: C

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

The total voltage of a series circuit is the _____________. A. sum of the individual voltage drops B. total resistance divided by the total current C. sum of the individual currents multiplied by the number of resistors D. total current divided by the total resistance

Description : The total voltage of a series circuit is the _____________. A. sum of the individual voltage drops B. total resistance divided by the total current C. sum of the individual currents multiplied by the number of resistors D. total current divided by the total resistance

Last Answer : Answer: A

The total resistance of a parallel circuit is always ____________. A. larger than that of the branch with the greatest resistance B. smaller than that of the branch with the lowest resistance C. equal to the sum of the individual branch resistances D. equal to the sum of the individual branch resistances divided by the number of branches

Description : The total resistance of a parallel circuit is always ____________. A. larger than that of the branch with the greatest resistance B. smaller than that of the branch with the lowest resistance C ... resistances D. equal to the sum of the individual branch resistances divided by the number of branches

Last Answer : Answer: B

The purpose of 'R6' in the winch circuit shown in the illustration is to _______________. EL-0102 A. maintain dry conditions within the winch brake box B. keep the series field current at a low value during 'fourth and fifth point lowering' C. act as the armature dynamic braking load to assist the winch in stopping D. limit the armature current during lowering operation with heavy loads

Description : The purpose of 'R6' in the winch circuit shown in the illustration is to _______________. EL-0102 A. maintain dry conditions within the winch brake box B. keep the series field current at ... to assist the winch in stopping D. limit the armature current during lowering operation with heavy loads

Last Answer : Answer: C

What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to point 'Z'. C. It depends on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Description : What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to ... on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Last Answer : Answer: B

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Description : The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Last Answer : Answer: C

The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load

Description : The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load

Last Answer : Answer: D

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: D

The advantage(s) of the method of D.C. motor speed control shown in the illustration is/are ______________. EL-0101 A. elimination of armature starting resistor losses B. elimination of speed instability with variable loads C. the ease of reversing motor direction D. all of the above

Description : The advantage(s) of the method of D.C. motor speed control shown in the illustration is/are ______________. EL-0101 A. elimination of armature starting resistor losses B. elimination of speed instability with variable loads C. the ease of reversing motor direction D. all of the above

Last Answer : Answer: D

The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Description : The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Last Answer : (B) Always occurs under a wheel load

The total resistance of a parallel circuit is always ____________. A. larger than the greatest branch resistance B. smaller than the lowest branch resistance C. equal to the sum of the individual branch resistances D. one-half the sum of the individual branch resistances

Description : The total resistance of a parallel circuit is always ____________. A. larger than the greatest branch resistance B. smaller than the lowest branch resistance C. equal to the sum of the individual branch resistances D. one-half the sum of the individual branch resistances

Last Answer : Answer: B

The least count of a Vernier scale is (A) Sum of the smallest divisions of main and Vernier scales (B) Value of one division of the primary scale divided by total number of divisions of Vernier scale (C) Value of one division of Vernier scale divided by total number of divisions of primary scale (D) None of these

Description : The least count of a Vernier scale is  (A) Sum of the smallest divisions of main and Vernier scales  (B) Value of one division of the primary scale divided by total number of divisions ... division of Vernier scale divided by total number of divisions of primary scale  (D) None of these 

Last Answer : (B) Value of one division of the primary scale divided by total number of divisions of Vernier  scale 

The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to obtain required speeds B. divert shunt field current for speed control in both directions of operation C. limit armature current in hoist and 'series field' current in lower to obtain required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Last Answer : Answer: C

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Last Answer : Answer: C

In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Last Answer : Answer: D

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

If two electrical loads are connected in parallel with each other and each load draw 6 amps what is the current of the circuit?

Description : If two electrical loads are connected in parallel with each other and each load draw 6 amps what is the current of the circuit?

Last Answer : 12 Amperes is.

Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range until a suitable reading is obtained. C. The indicating needle is deflected from left to right regardless of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Description : Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range ... of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Last Answer : Answer: A

The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens useful life C. energy is wasted if full loading is not utilized D. power factor correction methods are load dependent

Description : The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens ... wasted if full loading is not utilized D. power factor correction methods are load dependent

Last Answer : Answer: B

Which of the following statements is true concerning the operation of two alternators in parallel? A. The cycles per second of each alternator are the same. B. Both alternator governors must be set with the same amount of speed droop. C. The number of field poles must be the same on each alternator. D. The load must always be divided equally between alternators.

Description : Which of the following statements is true concerning the operation of two alternators in parallel? A. The cycles per second of each alternator are the same. B. Both alternator governors must be set ... be the same on each alternator. D. The load must always be divided equally between alternators.

Last Answer : Answer: A

When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Description : When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Last Answer : Answer: D

Sir , if there are 9 LEDs connected in series with the 9 volt battery and each led has a forward voltage drop of 1 volt , do i need a resistor in the circuit (in series with led)?

Description : 9 leds each of 1 volt drop is series with 9  volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !

Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

The smallest number by which 81 should be divided to make it a perfect cube is ___________

Description : The smallest number by which 81 should be divided to make it a perfect cube is ___________

Last Answer : The smallest number by which 81 should be divided to make it a perfect cube is ___________

When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors are tight B. test each resistor and capacitor on the card with an ohmmeter C. check the continuity of all printed circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Last Answer : Answer: A

When measuring AC current flow, you must always connect the meter _____________. A. in series with the power source and load B. in parallel with the power source and load C. insuring correct polarity D. using the lowest range possible to prevent instrument damage

Description : When measuring AC current flow, you must always connect the meter _____________. A. in series with the power source and load B. in parallel with the power source and load C. insuring correct polarity D. using the lowest range possible to prevent instrument damage

Last Answer : Answer: A

Which of the following statements represents the main difference between a relay and a contactor? A. Contactors control current and relays control voltage. B. A relay is series connected and a contactor is parallel connected. C. Contactors can handle heavier loads than relays. D. Contactors are made from silver and relays are made from copper.

Description : Which of the following statements represents the main difference between a relay and a contactor? A. Contactors control current and relays control voltage. B. A relay is series connected and a contactor ... loads than relays. D. Contactors are made from silver and relays are made from copper.

Last Answer : Answer: C

The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. contactor coil '3M' has many shorted turns B. resistor 'R8-A2' has an open C. contacts '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Description : The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. ... '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Last Answer : Answer: B

In the illustrated circuit 'A', what power is consumed by a 3 ohm resistor with a 12 volt source? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Description : In the illustrated circuit 'A', what power is consumed by a 3 ohm resistor with a 12 volt source? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Last Answer : Answer: B

In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Description : In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Last Answer : Answer: B

When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of span and wheel load under consideration (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration (C) The wheel load under consideration is midway between the centre of span and the centre of gravity of the load system (D) None of the above

Description : When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of ... the centre of span and the centre of gravity of the load system (D) None of the above

Last Answer : (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration

An ammeter should be used to measure ___________. A. the voltage between two points in a circuit B. circuit continuity C. current flow in a circuit D. total or partial circuit resistance

Description : An ammeter should be used to measure ___________. A. the voltage between two points in a circuit B. circuit continuity C. current flow in a circuit D. total or partial circuit resistance

Last Answer : Answer: C

Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board of all non-vital circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Description : Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board ... circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Last Answer : Answer: B

Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Description : Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Last Answer : The saturable current transformers linearly transforms the current upto twice the set current, but above this value the transformer core gets saturated and the secondary current is proportionally less. Thus ... overload. When current reduces the core gets de-saturated, as material design is such. 

In the illustration, the contacts between terminals 26 and 27 should be closed when _________. EL-0046 A. using one generator in isochronous mode only B. using two or more generators in parallel only C. the prime mover speed is to remain constant through varying loads in parallel or single operation D. the circuit breaker is closed for that generator

Description : In the illustration, the contacts between terminals 26 and 27 should be closed when _________. EL-0046 A. using one generator in isochronous mode only B. using two or more generators in ... through varying loads in parallel or single operation D. the circuit breaker is closed for that generator

Last Answer : Answer: C

Which is NOT a characteristic of a series circuit? w) The current is the same throughout. x) The total resistance is the sum of the individual resistance. y) The voltage of the source equals the sum of the circuit's individual voltage drops. z) The total resistance is the sum of the reciprocals of the individual resistances.

Description : Which is NOT a characteristic of a series circuit? w) The current is the same throughout. x) The total resistance is the sum of the individual resistance. y) The voltage of the source ... individual voltage drops. z) The total resistance is the sum of the reciprocals of the individual resistances.

Last Answer : ANSWER: Z -- THE TOTAL RESISTANCE IS THE SUM OF THE RECIPROCALS OF THE RECIPROCAL OF THE INDIVIDUAL RESISTANCES.

In a simply supported beam, bending moment at the end (a) Is always zero if it does not carry couple at the end (b) Is zero, if the beam has uniformly distributed load only (c) Is zero if the beam has concentrated loads only (d) May or may not be zero

Description : In a simply supported beam, bending moment at the end (a) Is always zero if it does not carry couple at the end (b) Is zero, if the beam has uniformly distributed load only (c) Is zero if the beam has concentrated loads only (d) May or may not be zero

Last Answer : (a) Is always zero if it does not carry couple at the end

Ramana divides two sums of money among his four sons Ganesh, Mahesh, Anil and Sunil. The first sum is divided in the ratio 4: 3: 2: 1 and second in the ratio 5: 6: 7: 8. If the second sum is twice the first, the largest total is received by a) Ganesh b) Mahesh c) Anil d) Sunil e) Both Ganesh and Mahesh

Description : Ramana divides two sums of money among his four sons Ganesh, Mahesh, Anil and Sunil. The first sum is divided in the ratio 4: 3: 2: 1 and second in the ratio 5: 6: 7: 8. If the second sum is ... first, the largest total is received by a) Ganesh b) Mahesh c) Anil d) Sunil e) Both Ganesh and Mahesh

Last Answer : Answer: A Let the first sum be 4x, 3x, 2x, x Second sum be 5y, 6y, 7y, 8y The second sum is twice the first sum 26y = 20x; 13y = 10x Take y=10 x= 13 G:M:A:S 4X+5Y: 3X+6Y: 2X +7Y: X+8Y 102: 99: 96: 93

Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor is started. B. The fuse works, but overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Description : Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor ... overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Last Answer : Answer: A

Which section of the circuit is responsible for maintaining a nearly constant voltage for all loads within its operating range? EL-0085 A. I B. II C. III D. IV

Description : Which section of the circuit is responsible for maintaining a nearly constant voltage for all loads within its operating range? EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: D

In the illustration, if one of the devices labeled 'TURB' should fail the ___________. EL-0003 A. device labeled 'EXC' will drive the alternator B. device labeled 'BKR' for that alternator should automatically open because of the reverse power relay C. operator must open all the devices labeled 'BKRS' to reduce the load on the remaining turbo-alternator D. emergency generator should automatically start and be placed on line to supply emergency load centers

Description : In the illustration, if one of the devices labeled 'TURB' should fail the ___________. EL-0003 A. device labeled 'EXC' will drive the alternator B. device labeled 'BKR' for that ... -alternator D. emergency generator should automatically start and be placed on line to supply emergency load centers

Last Answer : Answer: B