Which terminology deals with the excitation or stimulus applied to the system from an external source for the generation of an output? a. Input signal b. Output signal c. Error signal d. Feedback signal

Which terminology deals with the excitation or stimulus applied to the system from an external source for the generation of an output? a. Input signal b. Output signal c. Error signal d. Feedback signal
by

1 Answer

Answer :

Ans: A
by
selected by

Related questions

In the inverting configuration, the input signal is applied to the (a) (inverting, noninverting) input and the feedback signal is applied to the (b) (inverting, noninverting) input.

Description : In the inverting configuration, the input signal is applied to the (a) (inverting, noninverting) input and the feedback signal is applied to the (b) (inverting, noninverting) input.

Last Answer : a. Inverting. b. Inverting.

select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Last Answer : Both the input signal and the feedback signal.

The 'pitch controller module' shown in the illustration is fed the actual pitch position of the propeller from the _____________. EL-0095 A. 'pitch meter' B. 'pitch feedback potentiometer' C. #5 relay position D. pitch error signal

Description : The 'pitch controller module' shown in the illustration is fed the actual pitch position of the propeller from the _____________. EL-0095 A. 'pitch meter' B. 'pitch feedback potentiometer' C. #5 relay position D. pitch error signal

Last Answer : Answer: B

In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal from the resistor at the top of the speed sensing circuit card C. hall effect current to detect slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Last Answer : Answer: A

Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. A. Error Guessing B. Boundary Value Analysis C. Decision Table testing D. Equivalence partitioning

Description : Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. A. Error Guessing B. Boundary Value Analysis C. Decision Table testing D. Equivalence partitioning

Last Answer : D. Equivalence partitioning

Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. a) Error Guessing b) Boundary Value Analysis c) Decision Table testing d) Equivalence partitioning

Description : Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. a) Error Guessing b) Boundary Value Analysis c) Decision Table testing d) Equivalence partitioning

Last Answer : d) Equivalence partitioning

When a stimulus is applied on axonal membrane then generation of action potential is due to

Description : When a stimulus is applied on axonal membrane then generation of action potential is due to

Last Answer : When a stimulus is applied on axonal membrane then generation of action potential is due to

When a stimulus is applied on axonal membrane then generation of action potential is due to

Description : When a stimulus is applied on axonal membrane then generation of action potential is due to

Last Answer : When a stimulus is applied on axonal membrane then generation of action potential is due to

Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Last Answer : Answer: C

When an input signal A=11001 is applied to a NOT gate serially, its output signal is (A) 00111. (B) 00110. (C) 10101. (D) 11001.

Description : When an input signal A=11001 is applied to a NOT gate serially, its output signal is (A) 00111. (B) 00110. (C) 10101. (D) 11001.

Last Answer : When an input signal A=01001 is applied to a NOT gate serially , it's output signal is

This bistable electronic device assumes one of two stable output states, depending upon the state of the most recently applied input signal. In computer systems this device is used for storing information. Name this common electronic device.

Description : This bistable electronic device assumes one of two stable output states, depending upon the state of the most recently applied input signal. In computer systems this device is used for storing information. Name this common electronic device.

Last Answer : ANSWER: FLIP-FLOP or TOGGLE

Signal normally used to study non-ideal flow by stimulus response technique is __________ input. (A) Pulse (B) Step (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Signal normally used to study non-ideal flow by stimulus response technique is __________ input. (A) Pulse (B) Step (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In the skeletal muscle: a. myosin is found in the thick filament b. the thin filament contains actin and troponin c. during stimulus excitation calcium ions are derived from the serum d. tropomyosin masks the myosin-combining sites on the actin

Description : In the skeletal muscle: a. myosin is found in the thick filament b. the thin filament contains actin and troponin c. during stimulus excitation calcium ions are derived from the serum d. tropomyosin masks the myosin-combining sites on the actin

Last Answer : tropomyosin masks the myosin-combining sites on the actin

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity

Description : The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity

Last Answer : Ans: 1/11

For a feedback control system of type 2, the steady error for a rap input is

Description : For a feedback control system of type 2, the steady error for a rap input is  A) Infinite B) Constant C) Zero D) Indeterminate

Last Answer : For a feedback control system of type 2, the steady error for a rap input is Zero 

The speed of a synchronous motor is varied by _____________. A. interchanging any two of the three live leads B. changing the voltage of the system C. changing the input frequency D. increasing the field excitation

Description : The speed of a synchronous motor is varied by _____________. A. interchanging any two of the three live leads B. changing the voltage of the system C. changing the input frequency D. increasing the field excitation

Last Answer : Answer: C

If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the top lead positive with repect to the lower lead B. direct current, half wave rectified with a ripple frequency of 60 hz C. direct current with the top lead negative with repect to the lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

A synchronous motor maintains synchronism with the rotating field because _____________. A. field strength varies directly with rotor slip B. DC current applied to the rotor coils causes the rotor magnets to lock in with the rotating flux of the stator C. the stator poles are dragged around due to the flux created by the excitation current D. the stator flux rotates in the opposite direction

Description : A synchronous motor maintains synchronism with the rotating field because _____________. A. field strength varies directly with rotor slip B. DC current applied to the rotor coils causes the rotor ... the flux created by the excitation current D. the stator flux rotates in the opposite direction

Last Answer : Answer: B

Which set of truth table input signals will result in an output signal value of 1 from the 'AND' gate as shown in the illustration? EL-0035 A. 1-Jan B. Jan-00 C. 0-1 D. 0-0

Description : Which set of truth table input signals will result in an output signal value of 1 from the 'AND' gate as shown in the illustration? EL-0035 A. 1-Jan B. Jan-00 C. 0-1 D. 0-0

Last Answer : Answer: A

As shown in the illustration, which set of truth table input signals will result in an output signal at point 'Y'? EL-0035 A. 0-0 B. 0-1 C. Jan-00 D. 1-Jan

Description : As shown in the illustration, which set of truth table input signals will result in an output signal at point 'Y'? EL-0035 A. 0-0 B. 0-1 C. Jan-00 D. 1-Jan

Last Answer : Answer: D

The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' factor into the circuit C. shape the linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Description : The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' ... linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Last Answer : Answer: A

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

What type of feedback aids an input signal?

Description : What type of feedback aids an input signal?

Last Answer : Regenerative or positive

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will

Description : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

Last Answer : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will Reduce the noise

A change in field excitation of an alternator operating in parallel will cause a change in its _____________. A. alternator frequency B. kilowatt load C. voltage output D. all of the above

Description : A change in field excitation of an alternator operating in parallel will cause a change in its _____________. A. alternator frequency B. kilowatt load C. voltage output D. all of the above

Last Answer : Answer: C

The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the ____________. A. prime mover speed droop B. number of poles C. alternator field excitation D. load on the alternator

Description : The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the ____________. A. prime mover speed droop B. number of poles C. alternator field excitation D. load on the alternator

Last Answer : Answer: C

Why is it desirable to operate paralleled AC generators at the same power factor? A. Circulating currents are kept to a minimum. B. Field excitation losses are kept to a minimum. C. Generator rotors will have a lesser tendency to hunt. D. Because a power factor increase will decrease kilowatt output.

Description : Why is it desirable to operate paralleled AC generators at the same power factor? A. Circulating currents are kept to a minimum. B. Field excitation losses are kept to a minimum. C. Generator ... will have a lesser tendency to hunt. D. Because a power factor increase will decrease kilowatt output.

Last Answer : Answer: A

Teaching model is a way to Options: A) teach in a formal as well as informal way. B) Select such stimulus so that, the students may give expected feedback. C) Talk and think about instruction, which may contain facts in organized and classified manner. D) both (a) and ( b)

Description : Teaching model is a way to Options: A) teach in a formal as well as informal way. B) Select such stimulus so that, the students may give expected feedback. C) Talk and think about instruction, which may contain facts in organized and classified manner. D) both (a) and ( b)

Last Answer : D) both (a) and ( b) 

Comment on the effect of negative feedback on the gain, input and output resistance of the feedback amplifiers.Describe the gain bandwidth product term used in this context and its importance.

Description : Comment on the effect of negative feedback on the gain, input and output resistance of the feedback amplifiers.Describe the gain bandwidth product term used in this context and its importance.

Last Answer : Effect of negative feedback: 1. Gain decreases with negative feedback. 2. Input resistance increases with negative feedback. 3. Output resistance decreases with negative feedback. Explanation ... feedback bandwidth increases which means it is stable output on more range of frequency.

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ.

Description : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

Last Answer : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Description : The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Last Answer : Answer: C

The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Description : The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Last Answer : Answer: C

If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Description : If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Last Answer : Answer: B

A signal derived from a controlled function and returned to the initiating point is called a/an ____________. A. monitoring signal B. inverse signal C. reverse signal D. feedback signal

Description : A signal derived from a controlled function and returned to the initiating point is called a/an ____________. A. monitoring signal B. inverse signal C. reverse signal D. feedback signal

Last Answer : Answer: D

The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the throttle control circuit B. feedback resistor of the summing amplifier circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Last Answer : Answer: A

In the IBM PC-At, what do the words AT stand for A) Additional Terminals B) Advance technology C) Applied technology D) Advanced terminology

Description : In the IBM PC-At, what do the words AT stand for A) Additional Terminals B) Advance technology C) Applied technology D) Advanced terminology

Last Answer : Answer : B

Solvent extraction is the terminology applied to the liquid-liquid extraction, which is preferred for the separation of the components of liquids, when (A) Extracting solvent is cheaply & abundantly available (B) One of the liquid components is heat sensitive (C) Viscosity of liquid components is very high (D) One of the liquid components has very high affinity towards the solvent

Description : Solvent extraction is the terminology applied to the liquid-liquid extraction, which is preferred for the separation of the components of liquids, when (A) Extracting solvent is cheaply & abundantly available ... very high (D) One of the liquid components has very high affinity towards the solvent

Last Answer : (D) One of the liquid components has very high affinity towards the solvent

In the IBM PC-At, what do the words AT stand for a. Additional Terminals b. Advance technology c. Applied technology d. Advanced terminology

Description : In the IBM PC-At, what do the words AT stand for a. Additional Terminals b. Advance technology c. Applied technology d. Advanced terminology

Last Answer : Advance technology

In the IBM PC-At, what do the words AT stand for a. Additional Terminals b. Advance technology c. Applied technology d. Advanced terminology

Description : In the IBM PC-At, what do the words AT stand for a. Additional Terminals b. Advance technology c. Applied technology d. Advanced terminology

Last Answer : b. Advance technology

In the IBM PC-At, what do the words AT stand for a. Additional Terminals b. Advance technology c. Applied technology d. Advanced terminology

Description : In the IBM PC-At, what do the words AT stand for a. Additional Terminals b. Advance technology c. Applied technology d. Advanced terminology

Last Answer : b. Advance technology

In IT terminology failure in the kernel is called as (1) Crash (2) C r a s h dump (3) Dump (4) Kernel error

Description : In IT terminology failure in the kernel is called as (1) Crash (2) C r a s h dump (3) Dump (4) Kernel error

Last Answer :  Crash

The various stages occuring in GPS system are described below: 1. Generation of an output to the user 2. Detection of the GPS signals 3. Processing the data in the built-in-computer 4. Decoding the GPS signal. The correct sequence of the stages is: (A) 1, 2, 3, 4 (B) 2, 3, 4, 1 (C) 2, 4, 3, 1 (D) 3, 1, 2 , 4

Description : The various stages occuring in GPS system are described below: 1. Generation of an output to the user 2. Detection of the GPS signals 3. Processing the data in the built-in-computer 4. Decoding the GPS signal. The correct sequence of ... 4 (B) 2, 3, 4, 1 (C) 2, 4, 3, 1 (D) 3, 1, 2 , 4

Last Answer : Answer: Option C

If a step function is applied to the input of a system and the output...

Description : If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is?

Last Answer : If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is not necessarily stable.

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.

Technical study which deals with production, transport and delivery of a quality signal from source to destination. A. Transmission system engineering B. Communication system engineering C. Telephony engineering D. Telegraphic engineering

Description : Technical study which deals with production, transport and delivery of a quality signal from source to destination. A. Transmission system engineering B. Communication system engineering C. Telephony engineering D. Telegraphic engineering

Last Answer : A. Transmission system engineering

A forced vibration system vibrates at A) Natural frequency of the system B) Frequency of external excitation C) Frequency of internal excitation D) None of the above

Description : A forced vibration system vibrates at A) Natural frequency of the system B) Frequency of external excitation C) Frequency of internal excitation D) None of the above

Last Answer : B) Frequency of external excitation