Is a car battery AC or DC volts?

Is a car battery AC or DC volts?
by

1 Answer

Answer :

dc - the voltage is a constant 12 volts nominally in a normal car battery.
by
selected by

Related questions

Is a car battery AC or DC volts?

Description : Is a car battery AC or DC volts?

Last Answer : dc - the voltage is a constant 12 volts nominally in a normal car battery.

How many AC volts is 1 volt DC?

Description : How many AC volts is 1 volt DC?

Last Answer : They are apples and oranges. You can convert one to the other, depending on the amperage, but there is no corrolation between DC and AC.

If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Last Answer : Answer: D

The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Description : The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Last Answer : Answer: C

when charging a battery we use a DC supply but not an AC supply. Why ?

Description : when charging a battery we use a DC supply but not an AC supply. Why ?

Last Answer : When power is supplied to the battery, electrolyte inside the battery is divided into positive and negative ions, where ions with similar pole is gained in one side. This reactionʼs flow coincides with direct current.

Is current from a battery AC or DC?

Description : Is current from a battery AC or DC?

Last Answer : The current from the battery is DC

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B

If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Last Answer : Answer: A

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, if the device in figure 'A' has a step-up ratio of 10 to 1, what voltage should be measured at the secondary shortly after the primary of the device is connected to 110 volts DC? EL-0059 A. 0 volts B. 110 volts C. 11 volts D. 1100 volts

Description : In the illustration, if the device in figure 'A' has a step-up ratio of 10 to 1, what voltage should be measured at the secondary shortly after the primary of the device is connected to 110 volts DC? EL-0059 A. 0 volts B. 110 volts C. 11 volts D. 1100 volts

Last Answer : Answer: A

What happen if we give 220 volts dc supply to the bulb or tube light?

Description : What happen if we give 220 volts dc supply to the bulb or tube light?

Last Answer : Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

What Happen If We Give 220 Volts Dc Supply To D Bulb R Tube Light?

Description : What Happen If We Give 220 Volts Dc Supply To D Bulb R Tube Light?

Last Answer : Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

what happens if we give 220 volts dc supply to the bulb or tube light?

Description : what happens if we give 220 volts dc supply to the bulb or tube light?

Last Answer : A:Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current ... be so high that it may damage the bulb element. Low dc voltage will not damage the appliances

What happen if we give 220 volts dc supply to bulb or tube light?

Description : What happen if we give 220 volts dc supply to bulb or tube light?

Last Answer : Bulbs or devices for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

Telephone companies normally provide a voltage of __________to power telephones. (A) +24 volts DC (B) -24 volts DC (C) +48 volts DC (D) -48 volts DC.

Description : Telephone companies normally provide a voltage of __________to power telephones. (A) +24 volts DC (B) -24 volts DC (C) +48 volts DC (D) -48 volts DC.

Last Answer : (D) -48 volts DC.

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, has a flux of 0.4 mWb and the total number of conductors are 1000. What is the value of emf? (A) 100 Volts. (B) 0.1 Volts. (C) 1 Volts. (D) 10 Volts.

Description : A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, has a flux of 0.4 mWb and the total number of conductors are 1000. What is the value of emf? (A) 100 Volts. (B) 0.1 Volts. (C) 1 Volts. (D) 10 Volts.

Last Answer : Ans: D Given N = 1500 rpm, Φ = 0.4 mWb, Z = 1000, P = 4, & A= 4 Therefore, Eb = NΦPZ / 60 A = 1500 x 0.4 x 4 x 1000 x 10^-3 / 60 x 4 = 60/6 = 10 volts

What type of instrument is used to measure dc voltage of the order 5 volts?

Description : What type of instrument is used to measure dc voltage of the order 5 volts? (A) moving iron type (B) electro-static type (C) moving coil type (D) all of these

Last Answer : Permanent Magnet Moving Coil (PMMC) voltmeter is used to  measure the DC voltage. We can also use moving iron meter, but it has more error compared to moving coil.

How many amps in a 1000 watts at 110 volts ac?

Description : How many amps in a 1000 watts at 110 volts ac?

Last Answer : 9 amps would be the answer.

If 450 volts AC were measured across the load as shown in the illustration it would indicate a/an _______________. EL-0083 A. open winding between 'H1' and 'X1' B. properly operating circuit C. open winding between 'X1' and 'X4' D. ground on one side of 'Ep'

Description : If 450 volts AC were measured across the load as shown in the illustration it would indicate a/an _______________. EL-0083 A. open winding between 'H1' and 'X1' B. properly operating circuit C. open winding between 'X1' and 'X4' D. ground on one side of 'Ep'

Last Answer : Answer: C

If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Last Answer : 340 volts.

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

If a circuit contains a 1.5 volts battery and a bulb with a resistance of 3 ohms. calculate the current?

Description : If a circuit contains a 1.5 volts battery and a bulb with a resistance of 3 ohms. calculate the current?

Last Answer : Use Ohm's Law. Solving for current:I = V/R(current = voltage / resistance)

When using a charger to charge a ATV battery what settings should my charger be on 2 or 6 Amps 6 or 12 volts?

Description : When using a charger to charge a ATV battery what settings should my charger be on 2 or 6 Amps 6 or 12 volts?

Last Answer : Set the charger on 2 amps and 12 volts. Hopefully you have anauto off charger that will not overcharge the battery. If not thencharge the battery for 6 hours and then with a digital volt metercheck ... is 50% charged. 12 volts and it is 25% charged. Chargeadditional hours to reach a full charge.

How many volts is the Lenovo 40Y6797 Laptop Battery?

Description : How many volts is the Lenovo 40Y6797 Laptop Battery?

Last Answer : The Lenovo 40Y6797 Laptop Battery has 10.8 Volt DC. It is a lithium ion battery for the Thinkpad Z60M Series.

What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Description : What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Last Answer : Answer: A

A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Last Answer : Answer: C

Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Description : Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Last Answer : Answer: D

In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Last Answer : Answer: D

In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Last Answer : Answer: C

In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Last Answer : Answer: C

What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts

Description : What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts

Last Answer : Answer: A

What is the approximate voltage per cell produced by the nickel-iron (Edison) battery? A. 0.85 volts B. 1.35 volts C. 2.20 volts D. 6.05 volts

Description : What is the approximate voltage per cell produced by the nickel-iron (Edison) battery? A. 0.85 volts B. 1.35 volts C. 2.20 volts D. 6.05 volts

Last Answer : Answer: B

If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Description : If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Last Answer : Answer: C

The capacity of a storage battery is measured in ______________. A. volts B. ampere-hours C. farads D. amps

Description : The capacity of a storage battery is measured in ______________. A. volts B. ampere-hours C. farads D. amps

Last Answer : Answer: B

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

The open-circuit voltage of a fully charged lead-acid battery cell is _____________. A. 1.5 volts B. 1.8 volts C. 2.0 volts D. 2.3 volts

Description : The open-circuit voltage of a fully charged lead-acid battery cell is _____________. A. 1.5 volts B. 1.8 volts C. 2.0 volts D. 2.3 volts

Last Answer : Answer: C

How does a DC to AC inverter work?

Description : How does a DC to AC inverter work?

Last Answer : Start with a switching circuit that supplies the DC with one polarity then reverses the polarity, back and forth. That's done at the target AC frequency. An inverter that's any good will knock ... and will further attempt to smooth the wave to more closely resemble normal AC power from the mains.

I want to know what type of current does lightning consist of an ac, or dc?

Description : I want to know what type of current does lightning consist of an ac, or dc?

Last Answer : I thought ac meant alternating current, and dc meant direct current.

Can you hook up a capacitor to a home AC amp like you would in a car's DC amp? Possible at all?

Description : Can you hook up a capacitor to a home AC amp like you would in a car's DC amp? Possible at all?

Last Answer : I can’t see the word capacitor without immediately thinking of The Flux Capacitor and Back to the Future, doesn’t help you much, sorry.

What is Your Favourite Song From the New AC/DC Album "Black Ice"?

Description : What is Your Favourite Song From the New AC/DC Album "Black Ice"?

Last Answer : Well I haven’t really got to listen to it all the way through yet, but I’m really liking Money Made. Today, I plan to finish up listening and then I can give you my final verdict. Money Made, from what I’ve heard of it, sounds like a winner though!

4. The essential difference between an AC generator and a DC generator is that -Physics-10

Description : 4. The essential difference between an AC generator and a DC generator is that -Physics-10

Last Answer : AC generator has slip rings while the DC generator has a commutator. AC generators have two rings known as the slip rings while DC generators have two half rings known as the commutator. This is main difference between AC generator and DC generator.

In trapezium ABCD, AB|| DC and diagonals AC and BD intersect at O. If area of triangle AOD is 30cm square , find the area of triangle BOC -Maths 9th

Description : In trapezium ABCD, AB|| DC and diagonals AC and BD intersect at O. If area of triangle AOD is 30cm square , find the area of triangle BOC -Maths 9th

Last Answer : In the given figure: Area of triangle ADC = Area of triangle BCD (Triangles on the same and parallel) Now subtract the area of triangle DOC from both of them so... (Area of triangle ADC - Area of ... => Area of triangle AOD = Area of triangle BOC Hence the area of triangle BOC is 30 cm square.

In figure, ABCDE is any pentagon. BP drawn parallel to AC meets DC produced at P and EQ drawn parallel to AD meets CD produced at Q. -Maths 9th

Description : In figure, ABCDE is any pentagon. BP drawn parallel to AC meets DC produced at P and EQ drawn parallel to AD meets CD produced at Q. -Maths 9th

Last Answer : Given ABCDE is a pentagon. BP || AC and EQ|| AD. To prove ar (ABCDE) = ar (APQ) Proof We know that, triangles on the same base and between the same parallels are equal in area. Here, ΔADQ and ΔADE lie on the ... ar (ΔACD) = ar (ΔADE) + ar (ΔACB) + ar (ΔACD) ⇒ ar (ΔAPQ) = ar (ABCDE) Hence proved.

In trapezium ABCD, AB|| DC and diagonals AC and BD intersect at O. If area of triangle AOD is 30cm square , find the area of triangle BOC -Maths 9th

Description : In trapezium ABCD, AB|| DC and diagonals AC and BD intersect at O. If area of triangle AOD is 30cm square , find the area of triangle BOC -Maths 9th

Last Answer : In the given figure: Area of triangle ADC = Area of triangle BCD (Triangles on the same and parallel) Now subtract the area of triangle DOC from both of them so... (Area of triangle ADC - Area of ... => Area of triangle AOD = Area of triangle BOC Hence the area of triangle BOC is 30 cm square.

In figure, ABCDE is any pentagon. BP drawn parallel to AC meets DC produced at P and EQ drawn parallel to AD meets CD produced at Q. -Maths 9th

Description : In figure, ABCDE is any pentagon. BP drawn parallel to AC meets DC produced at P and EQ drawn parallel to AD meets CD produced at Q. -Maths 9th

Last Answer : Given ABCDE is a pentagon. BP || AC and EQ|| AD. To prove ar (ABCDE) = ar (APQ) Proof We know that, triangles on the same base and between the same parallels are equal in area. Here, ΔADQ and ΔADE lie on the ... ar (ΔACD) = ar (ΔADE) + ar (ΔACB) + ar (ΔACD) ⇒ ar (ΔAPQ) = ar (ABCDE) Hence proved.

ABC and DBC are two triangles on the same BC such that A and D lie on the opposite sides of BC,AB=AC and DB = DC.Show that AD is the perpendicular bisector of BC. -Maths 9th

Description : ABC and DBC are two triangles on the same BC such that A and D lie on the opposite sides of BC,AB=AC and DB = DC.Show that AD is the perpendicular bisector of BC. -Maths 9th

Last Answer : Solution :-