What is bigger 0.3mm or 0.13mm?

What is bigger 0.3mm or 0.13mm?
by

1 Answer

Answer :

The first one.
by

Related questions

What new breakthrough in mobile phone heat dissipation: successfully developed 0.3mm ultra-thin VC soaking plate with 5W heat dissipation power?

Description : What new breakthrough in mobile phone heat dissipation: successfully developed 0.3mm ultra-thin VC soaking plate with 5W heat dissipation power?

Last Answer : iBee Parts - Professional Factory Supplier For iPhone Samsung Huawei LCD Screen & Battery Repair Parts Replacement. Following heat pipe heat dissipation, VC heat sink technology has ... first domestic company to adopt precision etching microstructure integrated capillary core technology, and the

The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Description : The vertical distance clearance between the bottoms of the toe board? a. 0mm (0 inch) b. 6mm ( ¼ inch) c. 3mm ( 1/8 inch)

Last Answer : b. 6mm ( ¼ inch)

A cast crown fits on the die but not on the tooth, the discrepancy is about 0.3mm, what would you do: A. Relieve cast from the inside B. Take a new impression and make new crown C. Burnish margins D. Use thick mix of cement

Description : A cast crown fits on the die but not on the tooth, the discrepancy is about 0.3mm, what would you do: A. Relieve cast from the inside B. Take a new impression and make new crown C. Burnish margins D. Use thick mix of cement

Last Answer : B. Take a new impression and make new crown

When you try to seat a crown on a tooth you find a discrepancy of 0.3mm at the margin; you will: A. Reduce inner surface of crown B. Remake a new crown C. Smooth the enamel at the margin D. Hand burnish crown margins

Description : When you try to seat a crown on a tooth you find a discrepancy of 0.3mm at the margin; you will: A. Reduce inner surface of crown B. Remake a new crown C. Smooth the enamel at the margin D. Hand burnish crown margins

Last Answer : B. Remake a new crown

A crown casting with a chamfer margin fits the die; but in the mouth the casting is open approximately 0.3mm. A satisfactory fit and accurate physiological close of the gingival area of the crown can BEST be achieved by: A. Hand burnishing B. Mechanical burnishing C. Using finishing burs and points to remove the enamel margins on the tooth D. Making a new impression and remaking the crown E. Relieving the inside of the occlusal surface of the casting to allow for further

Description : A crown casting with a chamfer margin fits the die; but in the mouth the casting is open approximately 0.3mm. A satisfactory fit and accurate physiological close of the gingival area of the crown ... the crown E. Relieving the inside of the occlusal surface of the casting to allow for further

Last Answer : D. Making a new impression and remaking the crown

The gap between probing face and probing shoe should be. (i) 0.4 mm (ii) 0.2mm * (iii) 3mm (iv) 1mm.

Description : The gap between probing face and probing shoe should be. (i) 0.4 mm (ii) 0.2mm * (iii) 3mm (iv) 1mm.

Last Answer : (ii) 0.2mm *

In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Description : In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Last Answer : (i) +0.5mm, -0 mm in vertical *

Will I get good results using a flush trim router bit on 3mm carbon fiber plate?

Description : Will I get good results using a flush trim router bit on 3mm carbon fiber plate?

Last Answer : Carbon fiber composite edges will not mangle like Kevlar. It cuts more like fiberglass but downward forces could cause delamination. If you can trap the edges between two layers of support material, you ... . That way particles finer than the bag mesh won't get breathed in by the machinists.

What cars have this bolt pattern 5x114.3mm 5x4.5 inches?

Description : What cars have this bolt pattern 5x114.3mm 5x4.5 inches?

Last Answer : Acura, 1991-08AMC Eagle, 1989-93AMC, AMX, Concord, 1960-85Chrysler 300M, 1998-04Chrysler Concorde, 1993-04Chrysler Prowler, 1997-02Chrysler Sebring, 1995-08Chrysler Town and Country van, 1988-07Dodge ... full size car, 1957-77Ford Escape, 2001-08Ford Explorer, 1990-08And several hundred more.

What cars have this bolt pattern 5x114.3mm 5x4.5 inches?

Description : What cars have this bolt pattern 5x114.3mm 5x4.5 inches?

Last Answer : Acura, 1991-08AMC Eagle, 1989-93AMC, AMX, Concord, 1960-85Chrysler 300M, 1998-04Chrysler Concorde, 1993-04Chrysler Prowler, 1997-02Chrysler Sebring, 1995-08Chrysler Town and Country van, 1988-07Dodge ... full size car, 1957-77Ford Escape, 2001-08Ford Explorer, 1990-08And several hundred more.

If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm

Description : If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm

Last Answer : c) 24mm