A crown casting with a chamfer margin fits the die; but in the mouth the casting is open approximately 0.3mm. A satisfactory fit and accurate physiological close of the gingival area of the crown can BEST be achieved by: A. Hand burnishing B. Mechanical burnishing C. Using finishing burs and points to remove the enamel margins on the tooth D. Making a new impression and remaking the crown E. Relieving the inside of the occlusal surface of the casting to allow for further

A crown casting with a chamfer margin fits the die; but in the mouth the casting is open  approximately 0.3mm. A satisfactory fit and accurate physiological close of the gingival area of  the crown can BEST be achieved by:
A. Hand burnishing
B. Mechanical burnishing
C. Using finishing burs and points to remove the enamel margins on the tooth
D. Making a new impression and remaking the crown
E. Relieving the inside of the occlusal surface of the casting to allow for further
by

1 Answer

Answer :

D. Making a new impression and remaking the crown
by

Related questions

A cast crown fits on the die but not on the tooth, the discrepancy is about 0.3mm, what would you do: A. Relieve cast from the inside B. Take a new impression and make new crown C. Burnish margins D. Use thick mix of cement

Description : A cast crown fits on the die but not on the tooth, the discrepancy is about 0.3mm, what would you do: A. Relieve cast from the inside B. Take a new impression and make new crown C. Burnish margins D. Use thick mix of cement

Last Answer : B. Take a new impression and make new crown

When you try to seat a crown on a tooth you find a discrepancy of 0.3mm at the margin; you will: A. Reduce inner surface of crown B. Remake a new crown C. Smooth the enamel at the margin D. Hand burnish crown margins

Description : When you try to seat a crown on a tooth you find a discrepancy of 0.3mm at the margin; you will: A. Reduce inner surface of crown B. Remake a new crown C. Smooth the enamel at the margin D. Hand burnish crown margins

Last Answer : B. Remake a new crown

In preparing a very small proximal amalgam cavity on a molar tooth what would consider, A. Extend the cavity to the gingival margin B. Extend the cavity beyond the contacts areas C. Achieve at least 2mm in dentine D. Extend cavity just beyond dento enamel junction

Description : In preparing a very small proximal amalgam cavity on a molar tooth what would consider, A. Extend the cavity to the gingival margin B. Extend the cavity beyond the contacts areas C. Achieve at least 2mm in dentine D. Extend cavity just beyond dento enamel junction

Last Answer : D. Extend cavity just beyond dento enamel junction

The minimal labial tooth reduction for satisfactory aesthetics with porcelain fused to metal crown is, A. 1mm B. The full thickness of enamel C. 1.5 mm D. 2.5mm E. One third of the dentine thickness

Description : The minimal labial tooth reduction for satisfactory aesthetics with porcelain fused to metal crown is, A. 1mm B. The full thickness of enamel C. 1.5 mm D. 2.5mm E. One third of the dentine thickness

Last Answer : C. 1.5 mm

The bur should be tilted lingually when preparing the occlusal surface of class II cavity on a mandibular first premolar in order to: I. Remove unsupported enamel II. Prevent encroachment on the buccal pulp horn III. Prevent encroachment on the lingual pulp horn IV. Maintain dentinal support of the lingual cusp A. I and II B. I and III C. II and IV D. III and IV E. IV only

Description : The bur should be tilted lingually when preparing the occlusal surface of class II cavity on a mandibular first premolar in order to: I. Remove unsupported enamel II. Prevent encroachment on the buccal pulp horn III. Prevent ... and II B. I and III C. II and IV D. III and IV E. IV only

Last Answer : C. II and IV

Which one of the following is the major disadvantage of stone dies used for crown fabrication, A. They lack accurate reproduction of surface details B. Their overall dimensions are slightly smaller than the original impression C. The strength of the stone D. The hazard of aspiration of toxic materials during trimming of the dies.

Description : Which one of the following is the major disadvantage of stone dies used for crown fabrication, A. They lack accurate reproduction of surface details B. Their overall dimensions are slightly smaller than ... of the stone D. The hazard of aspiration of toxic materials during trimming of the dies.

Last Answer : A. They lack accurate reproduction of surface details

The main purpose of finishing the enamel walls is, A. Remove loose enamel rods B. Provide a better surface for the adoption of restorative material The main purpose of finishing the enamel walls is, A. Remove loose enamel rods B. Provide a better surface for the adoption of restorative material

Description : The main purpose of finishing the enamel walls is, A. Remove loose enamel rods B. Provide a better surface for the adoption of restorative material

Last Answer : A. Remove loose enamel rods

Why do you construct a lower removable partial denture with lingual bar: A. It is used when the space between raised floor, mouth and gingival margin is minimal B. Plaque accumulation is less than with lingual plate C. Should be made thicker when short

Description : Why do you construct a lower removable partial denture with lingual bar: A. It is used when the space between raised floor, mouth and gingival margin is minimal B. Plaque accumulation is less than with lingual plate C. Should be made thicker when short

Last Answer : B. Plaque accumulation is less than with lingual plate

What is true about partial dentures, A. They cause immediate changes in the oral plaque behaviour B. Night wearing of dentures reduces plaque accumulation C. Relieving the gingival area reduces the gingival enlargement.

Description : What is true about partial dentures, A. They cause immediate changes in the oral plaque behaviour B. Night wearing of dentures reduces plaque accumulation C. Relieving the gingival area reduces the gingival enlargement.

Last Answer : A. They cause immediate changes in the oral plaque behaviour

In the construction of a full veneer gold crown, future recession of gingival tissue can be prevented or at least minimised by, A. Extension of the crown 1 mm under the gingival crevice B. Reproduction of normal tooth incline in the gingival one third of the crown C. Slight over contouring of the tooth in the gingival one fifth of the crown D. Slight under contouring of the tooth in the gingival one fifth of the crown

Description : In the construction of a full veneer gold crown, future recession of gingival tissue can be prevented or at least minimised by, A. Extension of the crown 1 mm under the gingival crevice B. ... of the crown D. Slight under contouring of the tooth in the gingival one fifth of the crown

Last Answer : B. Reproduction of normal tooth incline in the gingival one third of the crown

The cervical finish line of a full veneer crown preparation should be placed: A. Just supragingival whenever is possible B. According to the depth of gingival crevice C. Subgingival to reduce ability of recurrent caries D. At the junction of tooth and amalgam core

Description : The cervical finish line of a full veneer crown preparation should be placed: A. Just supragingival whenever is possible B. According to the depth of gingival crevice C. Subgingival to reduce ability of recurrent caries D. At the junction of tooth and amalgam core

Last Answer : A. Just supragingival whenever is possible

The MAIN purpose of burnishing is: A. To help eliminating excess mercury (condensing) B. To condense margins C. Polishing of filling

Description : The MAIN purpose of burnishing is: A. To help eliminating excess mercury (condensing) B. To condense margins C. Polishing of filling

Last Answer : B. To condense margins

A partial denture that seats on the master cast but fails to seat correctly in the mouth is a result of, A. Contraction of the metal framework during casting B. Insufficient expansion of the investment material C. Distortion of impression D. Failure to block out unwanted undercuts

Description : A partial denture that seats on the master cast but fails to seat correctly in the mouth is a result of, A. Contraction of the metal framework during casting B. Insufficient expansion of the investment material C. Distortion of impression D. Failure to block out unwanted undercuts

Last Answer : C. Distortion of impression

After making an impression to reline an RPD the dentist notes that the indirect retainers are not resting on the tooth. To avoid this, what process should have undertaken initially: A. Ask patient to bite firmly while impression is setting B. Hold the metal base frame against the abutment tooth while setting C. Fabricate new denture D. Add impression material and close the gap

Description : After making an impression to reline an RPD the dentist notes that the indirect retainers are not resting on the tooth. To avoid this, what process should have undertaken initially: A. Ask ... abutment tooth while setting C. Fabricate new denture D. Add impression material and close the gap

Last Answer : B. Hold the metal base frame against the abutment tooth while setting

Odontogenic cysts develop from the following structures except: A. Reduced enamel epithelium of tooth crown B. Dental lamina dura C. Epithelium trapped after sutures D. ertwig’s root sheath

Description : Odontogenic cysts develop from the following structures except: A. Reduced enamel epithelium of tooth crown B. Dental lamina dura C. Epithelium trapped after sutures D. ertwig’s root sheath

Last Answer : C. Epithelium trapped after sutures

When primary molars are prepared for stainless steel crowns, should the depth for reduction of the proximal surface be similar to the depth of the buccal and lingual surfaces? A. Yes; reduction of all wall is similar for best retention B. No, proximal reduction is greater to allow the crown to pass the contact area C. No, the buccal surfaces has the greatest reduction to remove the cervical bulge D. Yes, all undercuts are uniformly removed so that the steel crown can be seated E. No, because of lateral constriction, the lingual surface needs greatest reduction

Description : When primary molars are prepared for stainless steel crowns, should the depth for reduction of the proximal surface be similar to the depth of the buccal and lingual surfaces? A. Yes; reduction ... can be seated E. No, because of lateral constriction, the lingual surface needs greatest reduction

Last Answer : B. No, proximal reduction is greater to allow the crown to pass the contact area

A vital tooth has a crown cemented to a pin-retained amalgam core; where does a failure occur: A. Between crown and cement B. Between core and cement C. In the crown and the root D. In the core and the margin preparation

Description : A vital tooth has a crown cemented to a pin-retained amalgam core; where does a failure occur: A. Between crown and cement B. Between core and cement C. In the crown and the root D. In the core and the margin preparation

Last Answer : B. Between core and cement

Marginal leakage at the proximal gingival cavosurface of a recently restored class II can be caused by: I. Insufficient condensation II. First proximal increment was too large III. Neglecting to wedge the matrix IV. Hand manipulation instead of mechanical V. Debris contamination A. I, II, III B. II, III, IV C. I, II, V D. None of the above E. All of the above

Description : Marginal leakage at the proximal gingival cavosurface of a recently restored class II can be caused by: I. Insufficient condensation II. First proximal increment was too large III. Neglecting to wedge the matrix IV. Hand ... III, IV C. I, II, V D. None of the above E. All of the above

Last Answer : C. I, II, V

Calculus attaches to teeth surfaces by: A. Acquired pellicle B. Interlocking to the crystals of the tooth C. Penetrated into enamel and dentine D. Mechanical interlocking E. All of the above

Description : Calculus attaches to teeth surfaces by: A. Acquired pellicle B. Interlocking to the crystals of the tooth C. Penetrated into enamel and dentine D. Mechanical interlocking E. All of the above

Last Answer : E. All of the above

Dental caries of the proximal surfaces usually starts at, A. Somewhere between the ridge and the contact area B. Just gingival to contact areas C. Just about the gingival margin

Description : Dental caries of the proximal surfaces usually starts at, A. Somewhere between the ridge and the contact area B. Just gingival to contact areas C. Just about the gingival margin

Last Answer : B. Just gingival to contact areas

Where is the retentive position on teeth according to the survey line: A. Below the height of contour B. Next to gingival margins

Description : Where is the retentive position on teeth according to the survey line: A. Below the height of contour B. Next to gingival margins

Last Answer : A. Below the height of contour

.When correction preparation for re contouring of occlusal surface is to be applied, grinding only of the adjusted surface: A. Should not be felt flat B. Requires a flat crown C. Requires no contact with adjacent teeth D. Should be felt flat

Description : .When correction preparation for re contouring of occlusal surface is to be applied, grinding only of the adjusted surface: A. Should not be felt flat B. Requires a flat crown C. Requires no contact with adjacent teeth D. Should be felt flat

Last Answer : A. Should not be felt flat

What is the relationship of the retentive portion of the partial dentures retainers to the survey line of abutment: A. Gingival /Below/ B. Occlusal /Above/ C. No relation

Description : What is the relationship of the retentive portion of the partial dentures retainers to the survey line of abutment: A. Gingival /Below/ B. Occlusal /Above/ C. No relation

Last Answer : A. Gingival /Below/

If used, in which direction should pinholes be placed? a. parallel to the long axis of the tooth b.parallel to the nearest external surface c. at a 15 degree angle to the long axis of the tooth d. perpendicular to the gingival floor e. directly below and parallel to restored cusp tip

Description : If used, in which direction should pinholes be placed? a. parallel to the long axis of the tooth b.parallel to the nearest external surface c. at a 15 degree angle to the long axis of the tooth d. perpendicular to the gingival floor e. directly below and parallel to restored cusp tip

Last Answer : b.parallel to the nearest external surface

The removable partial denture requires relining what would be the most appropriate action, A. take a new impression by asking the patient to occlude on it B. Provide equal space (maybe it was thickness) between denture and gingival tissues. C. Make sure the framework and retainers are seated in place before taking impression

Description : The removable partial denture requires relining what would be the most appropriate action, A. take a new impression by asking the patient to occlude on it B. Provide equal space (maybe it was ... gingival tissues. C. Make sure the framework and retainers are seated in place before taking impression

Last Answer : C. Make sure the framework and retainers are seated in place before taking impression

The principal reasons for placing a gingival interproximal wedge in conjunction with a matrix for amalgam condensation are to: 1. separate the teeth slightly 2. keep the band tight at the gingival margin 3. contribute to the interproximal contact of the restoration 4. retract the gingival tissue a. 1,2,3 b. 1,2,4 c. 2,3,4 d. 1,3,4 e. all of the above

Description : The principal reasons for placing a gingival interproximal wedge in conjunction with a matrix for amalgam condensation are to: 1. separate the teeth slightly 2. keep the band tight at the gingival margin 3. contribute to the ... b. 1,2,4 c. 2,3,4 d. 1,3,4 e. all of the above

Last Answer : e. all of the above

The ”biologic width” is the distance between the A. Base of the gingival sulcus and the crest of alveolar bone B. Free gingival margin and the base of the gingival sulcus C. Free gingival margin and the alveolar bone D. Free gingival margin and the mucogingival junction E. Free gingival margin and the base of connective tissue attachment

Description : The biologic width is the distance between the A. Base of the gingival sulcus and the crest of alveolar bone B. Free gingival margin and the base of the gingival sulcus C. ... gingival margin and the mucogingival junction E. Free gingival margin and the base of connective tissue attachment

Last Answer : A. Base of the gingival sulcus and the crest of alveolar bone

The effectiveness of the acid etch is dependent on which of the following factors: A. Material must be used to clean the surface of the tooth prior to etching B. The effectiveness of the itchant C. The chemical and physical nature of the tooth D. The area and surface of the enamel to be itched

Description : The effectiveness of the acid etch is dependent on which of the following factors: A. Material must be used to clean the surface of the tooth prior to etching B. The effectiveness of the itchant C. The chemical and physical nature of the tooth D. The area and surface of the enamel to be itched

Last Answer : C. The chemical and physical nature of the tooth

In class II preparation it is difficult to place the gingival seat when preparation is extended too gingivally because the: A. Enamel rods are directed occlusally B. Marked cervical constriction

Description : In class II preparation it is difficult to place the gingival seat when preparation is extended too gingivally because the: A. Enamel rods are directed occlusally B. Marked cervical constriction

Last Answer : B. Marked cervical constriction

The gingiva of a child is diagnosed on the basis of all of these except of: A. Contour of gingival papilla B. Sulcus depth C. Contour of Nasmyth membrane (nasmyth description of the membrane is unclear that's why the term enamel cuticle is preferred D. Tight filling of gingival collar

Description : The gingiva of a child is diagnosed on the basis of all of these except of: A. Contour of gingival papilla B. Sulcus depth C. Contour of Nasmyth membrane (nasmyth description of the membrane is unclear that's why the term enamel cuticle is preferred D. Tight filling of gingival collar

Last Answer : C. Contour of Nasmyth membrane (nasmyth description of the membrane is unclear that's why the term enamel cuticle is preferred

Amalgam restoration, when do you have to replace it? a. Ditching of the edges. b. The probe penetrates the area between the margin and tooth tissue. c. Fissure of the surface of the amalgam. d. When there is chronic inflammation of the pulp.

Description : Amalgam restoration, when do you have to replace it? a. Ditching of the edges. b. The probe penetrates the area between the margin and tooth tissue. c. Fissure of the surface of the amalgam. d. When there is chronic inflammation of the pulp.

Last Answer : c. Fissure of the surface of the amalgam.

It is desirable for major connectors of upper partial dentures to:** A. Be at least 5 mm away from the gingival margin B. Cover the anterior palate

Description : It is desirable for major connectors of upper partial dentures to:** A. Be at least 5 mm away from the gingival margin B. Cover the anterior palate

Last Answer : A. Be at least 5 mm away from the gingival margin

In regard to carbide burs; the more number of cutting blades and low speed will result in: A. Less efficient cutting and a smoother surface B. Less efficient cutting and a rougher surface C. More efficient cutting and a smoother surface D. More efficient cutting and a rougher surface

Description : In regard to carbide burs; the more number of cutting blades and low speed will result in: A. Less efficient cutting and a smoother surface B. Less efficient cutting and a rougher surface C. More efficient cutting and a smoother surface D. More efficient cutting and a rougher surface

Last Answer : A. Less efficient cutting and a smoother surface

Which of the following statement about the defective margins of amalgam restorations is true?+M07 A. The larger the breakdown, the greater the chance of decay. IF THERE IS MARGINAL BREAKDOWN THIS DOSNT NECESSITATE THE PRESENCE OF CARIES ALONG MARGIN So the ans is Chances are increased

Description : Which of the following statement about the defective margins of amalgam restorations is true?+M07 A. The larger the breakdown, the greater the chance of decay. IF THERE IS MARGINAL BREAKDOWN THIS DOSNT NECESSITATE THE PRESENCE OF CARIES ALONG MARGIN So the ans is Chances are increased

Last Answer : A. The larger the breakdown, the greater the chance of decay.

A tooth under occlusal trauma shows A. Bone resorption B. Necrosis of the pulp C. Hypercementosis D. Triangulation Vertical defects occur adjacent to a tooth and usually in the form of a triangular area of missing bone, known as triangulation E. All of the above

Description : A tooth under occlusal trauma shows A. Bone resorption B. Necrosis of the pulp C. Hypercementosis D. Triangulation Vertical defects occur adjacent to a tooth and usually in the form of a triangular area of missing bone, known as triangulation E. All of the above

Last Answer : E. All of the above

The surface of enamel rod prisms in permanent teeth is: A. Perpendicular to the outer surface of the tooth B. Parallel to the outer surface of the tooth C. Parallel to enamel contour D. Parallel to enamel-dentine contour

Description : The surface of enamel rod prisms in permanent teeth is: A. Perpendicular to the outer surface of the tooth B. Parallel to the outer surface of the tooth C. Parallel to enamel contour D. Parallel to enamel-dentine contour

Last Answer : A. Perpendicular to the outer surface of the tooth

What is the main purpose of using Stress breakers: A. To distribute the load between teeth and ridges B. To distribute the load between the clasps and the face end of the saddle C. It relieves the abutment tooth of occlusal loads that may exceed their physiologic strength

Description : What is the main purpose of using Stress breakers: A. To distribute the load between teeth and ridges B. To distribute the load between the clasps and the face end of the saddle C. It relieves the abutment tooth of occlusal loads that may exceed their physiologic strength

Last Answer : C. It relieves the abutment tooth of occlusal loads that may exceed their physiologic strength

In regard to Chlorhexidine mouth wash:** A. Is anionic ( opposite) B. Used in 0.02% concentration ( topical skin) C. Used in 0.12% concentration D. Penetrates the gingival crevice/pocket ( no)

Description : In regard to Chlorhexidine mouth wash:** A. Is anionic ( opposite) B. Used in 0.02% concentration ( topical skin) C. Used in 0.12% concentration D. Penetrates the gingival crevice/pocket ( no)

Last Answer : C. Used in 0.12% concentration

The normal range of gingival depth “Epithelial attachment” in healthy mouth is: A. 1-2 mm B. 0-3 mm C. 2-3 mm D. 0-5 mm

Description : The normal range of gingival depth “Epithelial attachment” in healthy mouth is: A. 1-2 mm B. 0-3 mm C. 2-3 mm D. 0-5 mm

Last Answer : C. 2-3 mm

A 8 years-old patient has 3 first premolars erupted and a swelling on the ridge of the un-erupted premolar. X ray shows a fully developed crown and ¾ roots development with no other pathology. What is your management: A. Remove the dentigerous cyst B. Soft tissues recision to allow eruption C. Soft tissues recision accompanied with orthodontic appliance to help with eruption

Description : A 8 years-old patient has 3 first premolars erupted and a swelling on the ridge of the un-erupted premolar. X ray shows a fully developed crown and ¾ roots development with no ... recision to allow eruption C. Soft tissues recision accompanied with orthodontic appliance to help with eruption

Last Answer : C. Soft tissues recision accompanied with orthodontic appliance to help with eruption

Which is NOT usually related to gingival inflammation in children? A. Endocrine disturbance B. Viral infection C. Mouth breathing D. Spirochetal infection E. Streptococcal infection

Description : Which is NOT usually related to gingival inflammation in children? A. Endocrine disturbance B. Viral infection C. Mouth breathing D. Spirochetal infection E. Streptococcal infection

Last Answer : D. Spirochetal infection

During teeth eruption, the reduced enamel epithelium merges with the oral epithelium. What is the further development? A. Downgrowth of oral epithelium which replaces the reduced enamel epithelium B. Proliferation of inner enamel epithelium C. Proliferation of outer enamel epithelium D. Down growth of oral epithelium which undermines the reduced enamel epithelium E. Gradual transformation of the reduced enamel epithelium

Description : During teeth eruption, the reduced enamel epithelium merges with the oral epithelium. What is the further development? A. Downgrowth of oral epithelium which replaces the reduced enamel ... which undermines the reduced enamel epithelium E. Gradual transformation of the reduced enamel epithelium

Last Answer : E. Gradual transformation of the reduced enamel epithelium

The vertical incision of a mucoperiostal flap should: A. Always extend to the alveolar mucoperiostal B. Bisect the middle of gingival papillae C. Be at the right angle of the tooth

Description : The vertical incision of a mucoperiostal flap should: A. Always extend to the alveolar mucoperiostal B. Bisect the middle of gingival papillae C. Be at the right angle of the tooth

Last Answer : A. Always extend to the alveolar mucoperiostal

What is TRUE in regard to the preparation of occlusal rests: A. Use an inverted cone bur B. Use a flat fissure bur C. Parallel to occlusal plane D. At right angle to the long axis of tooth E. None of the above

Description : What is TRUE in regard to the preparation of occlusal rests: A. Use an inverted cone bur B. Use a flat fissure bur C. Parallel to occlusal plane D. At right angle to the long axis of tooth E. None of the above

Last Answer : E. None of the above

Tooth under occlusal trauma may show: A. Bone resorption B. Necrosis of the pulp C. Hypercementosis D. Triangulation E. All of the above

Description : Tooth under occlusal trauma may show: A. Bone resorption B. Necrosis of the pulp C. Hypercementosis D. Triangulation E. All of the above

Last Answer : E. All of the above

Which of the following is true regarding preparation of custom tray for elastomeric impression: a. Adhesive is preferred over perforation. b. Perforation provides adequate retention c. Adhesive is applied immediately before procedure d. Perforations are not made in the area over the prepared tooth .

Description : Which of the following is true regarding preparation of custom tray for elastomeric impression: a. Adhesive is preferred over perforation. b. Perforation provides adequate retention c. Adhesive is ... before procedure d. Perforations are not made in the area over the prepared tooth .

Last Answer : a. Adhesive is preferred over perforation.

.Which of the following is true regarding preparation of custom tray for elastomeric impression: A. Adhesive is preferred over perforation B. Perforation provides adequate retention C. Adhesive is applied immediately before procedure D. Perforations are not made in the area over the prepared tooth

Description : .Which of the following is true regarding preparation of custom tray for elastomeric impression: A. Adhesive is preferred over perforation B. Perforation provides adequate retention C. Adhesive is ... immediately before procedure D. Perforations are not made in the area over the prepared tooth

Last Answer : A. Adhesive is preferred over perforation

An impression with elastomer in custom tray has been taken for crown preparation; it will be two days before the impression gets to the laboratory for construction of the crown. Which impression material is preferred? A. Polyether B. Thiokol or meraptan rubber C. Condensation silicone D. Vinyl polysiloxane

Description : An impression with elastomer in custom tray has been taken for crown preparation; it will be two days before the impression gets to the laboratory for construction of the crown. Which impression ... A. Polyether B. Thiokol or meraptan rubber C. Condensation silicone D. Vinyl polysiloxane

Last Answer : D. Vinyl polysiloxane

An occlusal approaching clasp TIP, A. Should occupy a predetermined undercut B. Contact the tooth under the survey line C. Rigid

Description : An occlusal approaching clasp TIP, A. Should occupy a predetermined undercut B. Contact the tooth under the survey line C. Rigid

Last Answer : B. Contact the tooth under the survey line