A cast crown fits on the die but not on the tooth, the discrepancy is about 0.3mm, what would you do: A. Relieve cast from the inside B. Take a new impression and make new crown C. Burnish margins D. Use thick mix of cement

A cast crown fits on the die but not on the tooth, the discrepancy is about 0.3mm, what would you do:
A. Relieve cast from the inside
B. Take a new impression and make new crown
C. Burnish margins
D. Use thick mix of cement
by

1 Answer

Answer :

B. Take a new impression and make new crown
by

Related questions

When you try to seat a crown on a tooth you find a discrepancy of 0.3mm at the margin; you will: A. Reduce inner surface of crown B. Remake a new crown C. Smooth the enamel at the margin D. Hand burnish crown margins

Description : When you try to seat a crown on a tooth you find a discrepancy of 0.3mm at the margin; you will: A. Reduce inner surface of crown B. Remake a new crown C. Smooth the enamel at the margin D. Hand burnish crown margins

Last Answer : B. Remake a new crown

A crown casting with a chamfer margin fits the die; but in the mouth the casting is open approximately 0.3mm. A satisfactory fit and accurate physiological close of the gingival area of the crown can BEST be achieved by: A. Hand burnishing B. Mechanical burnishing C. Using finishing burs and points to remove the enamel margins on the tooth D. Making a new impression and remaking the crown E. Relieving the inside of the occlusal surface of the casting to allow for further

Description : A crown casting with a chamfer margin fits the die; but in the mouth the casting is open approximately 0.3mm. A satisfactory fit and accurate physiological close of the gingival area of the crown ... the crown E. Relieving the inside of the occlusal surface of the casting to allow for further

Last Answer : D. Making a new impression and remaking the crown

A vital tooth has a crown cemented to a pin-retained amalgam core; where does a failure occur: A. Between crown and cement B. Between core and cement C. In the crown and the root D. In the core and the margin preparation

Description : A vital tooth has a crown cemented to a pin-retained amalgam core; where does a failure occur: A. Between crown and cement B. Between core and cement C. In the crown and the root D. In the core and the margin preparation

Last Answer : B. Between core and cement

The major etiological factor responsible for Class II division 2 malocclusion in Angle’s classification is:** A. Thumb sucking B. Growth discrepancy C. Tongue thrust habit D. Tooth to jaw size discrepancy E. Skeletal cause (discrepancy)

Description : The major etiological factor responsible for Class II division 2 malocclusion in Angle’s classification is:** A. Thumb sucking B. Growth discrepancy C. Tongue thrust habit D. Tooth to jaw size discrepancy E. Skeletal cause (discrepancy)

Last Answer : E. Skeletal cause (discrepancy)

Which one of the following is the major disadvantage of stone dies used for crown fabrication, A. They lack accurate reproduction of surface details B. Their overall dimensions are slightly smaller than the original impression C. The strength of the stone D. The hazard of aspiration of toxic materials during trimming of the dies.

Description : Which one of the following is the major disadvantage of stone dies used for crown fabrication, A. They lack accurate reproduction of surface details B. Their overall dimensions are slightly smaller than ... of the stone D. The hazard of aspiration of toxic materials during trimming of the dies.

Last Answer : A. They lack accurate reproduction of surface details

An impression with elastomer in custom tray has been taken for crown preparation; it will be two days before the impression gets to the laboratory for construction of the crown. Which impression material is preferred? A. Polyether B. Thiokol or meraptan rubber C. Condensation silicone D. Vinyl polysiloxane

Description : An impression with elastomer in custom tray has been taken for crown preparation; it will be two days before the impression gets to the laboratory for construction of the crown. Which impression ... A. Polyether B. Thiokol or meraptan rubber C. Condensation silicone D. Vinyl polysiloxane

Last Answer : D. Vinyl polysiloxane

After making an impression to reline an RPD the dentist notes that the indirect retainers are not resting on the tooth. To avoid this, what process should have undertaken initially: A. Ask patient to bite firmly while impression is setting B. Hold the metal base frame against the abutment tooth while setting C. Fabricate new denture D. Add impression material and close the gap

Description : After making an impression to reline an RPD the dentist notes that the indirect retainers are not resting on the tooth. To avoid this, what process should have undertaken initially: A. Ask ... abutment tooth while setting C. Fabricate new denture D. Add impression material and close the gap

Last Answer : B. Hold the metal base frame against the abutment tooth while setting

A partial denture that seats on the master cast but fails to seat correctly in the mouth is a result of, A. Contraction of the metal framework during casting B. Insufficient expansion of the investment material C. Distortion of impression D. Failure to block out unwanted undercuts

Description : A partial denture that seats on the master cast but fails to seat correctly in the mouth is a result of, A. Contraction of the metal framework during casting B. Insufficient expansion of the investment material C. Distortion of impression D. Failure to block out unwanted undercuts

Last Answer : C. Distortion of impression

Which of the following is true regarding preparation of custom tray for elastomeric impression: a. Adhesive is preferred over perforation. b. Perforation provides adequate retention c. Adhesive is applied immediately before procedure d. Perforations are not made in the area over the prepared tooth .

Description : Which of the following is true regarding preparation of custom tray for elastomeric impression: a. Adhesive is preferred over perforation. b. Perforation provides adequate retention c. Adhesive is ... before procedure d. Perforations are not made in the area over the prepared tooth .

Last Answer : a. Adhesive is preferred over perforation.

.Which of the following is true regarding preparation of custom tray for elastomeric impression: A. Adhesive is preferred over perforation B. Perforation provides adequate retention C. Adhesive is applied immediately before procedure D. Perforations are not made in the area over the prepared tooth

Description : .Which of the following is true regarding preparation of custom tray for elastomeric impression: A. Adhesive is preferred over perforation B. Perforation provides adequate retention C. Adhesive is ... immediately before procedure D. Perforations are not made in the area over the prepared tooth

Last Answer : A. Adhesive is preferred over perforation

.Oil or water on impression for treatment casts causes: A. An increase of the quality B. No alteration C. A decrease of the quality D. Bubbles on the cast

Description : .Oil or water on impression for treatment casts causes: A. An increase of the quality B. No alteration C. A decrease of the quality D. Bubbles on the cast

Last Answer : C. A decrease of the quality

“Pop off” of a porcelain veneer from the under the lying gold crown is due to:** A. Too thick application of pure gold surface conditioner B. Contamination at the porcelain metal interface C. Under firing the opaque layer D. All of the above

Description : “Pop off” of a porcelain veneer from the under the lying gold crown is due to:** A. Too thick application of pure gold surface conditioner B. Contamination at the porcelain metal interface C. Under firing the opaque layer D. All of the above

Last Answer : B. Contamination at the porcelain metal interface

In the construction of a full veneer gold crown, future recession of gingival tissue can be prevented or at least minimised by, A. Extension of the crown 1 mm under the gingival crevice B. Reproduction of normal tooth incline in the gingival one third of the crown C. Slight over contouring of the tooth in the gingival one fifth of the crown D. Slight under contouring of the tooth in the gingival one fifth of the crown

Description : In the construction of a full veneer gold crown, future recession of gingival tissue can be prevented or at least minimised by, A. Extension of the crown 1 mm under the gingival crevice B. ... of the crown D. Slight under contouring of the tooth in the gingival one fifth of the crown

Last Answer : B. Reproduction of normal tooth incline in the gingival one third of the crown

The ideal length of core in the fabrication of crown and core of endodontically treated tooth is, A. 1.5 of crown length B. The length of the crown C. 2/3 tooth/root length D. ½ root length

Description : The ideal length of core in the fabrication of crown and core of endodontically treated tooth is, A. 1.5 of crown length B. The length of the crown C. 2/3 tooth/root length D. ½ root length

Last Answer : C. 2/3 tooth/root length

The OPTIMUM crown to root ratio for abutment tooth is:** A. 2:3 B. 1:1

Description : The OPTIMUM crown to root ratio for abutment tooth is:** A. 2:3 B. 1:1

Last Answer : A. 2:3

The cervical finish line of a full veneer crown preparation should be placed: A. Just supragingival whenever is possible B. According to the depth of gingival crevice C. Subgingival to reduce ability of recurrent caries D. At the junction of tooth and amalgam core

Description : The cervical finish line of a full veneer crown preparation should be placed: A. Just supragingival whenever is possible B. According to the depth of gingival crevice C. Subgingival to reduce ability of recurrent caries D. At the junction of tooth and amalgam core

Last Answer : A. Just supragingival whenever is possible

In regard to apically displaced flap, what is TRUE: A. Does not preserve attached gingivae B. Does not lengthen crown of tooth C. Is a pocket elimination procedure D. A & C

Description : In regard to apically displaced flap, what is TRUE: A. Does not preserve attached gingivae B. Does not lengthen crown of tooth C. Is a pocket elimination procedure D. A & C

Last Answer : C. Is a pocket elimination procedure

Odontogenic cysts develop from the following structures except: A. Reduced enamel epithelium of tooth crown B. Dental lamina dura C. Epithelium trapped after sutures D. ertwig’s root sheath

Description : Odontogenic cysts develop from the following structures except: A. Reduced enamel epithelium of tooth crown B. Dental lamina dura C. Epithelium trapped after sutures D. ertwig’s root sheath

Last Answer : C. Epithelium trapped after sutures

What is the ideal length for a post in post-core in an endodontically treated tooth: A. 2/3 of the tooth length B. ½ of the tooth length C. 1.5 times that of the crown D. Same as the anticipated crown

Description : What is the ideal length for a post in post-core in an endodontically treated tooth: A. 2/3 of the tooth length B. ½ of the tooth length C. 1.5 times that of the crown D. Same as the anticipated crown

Last Answer : A. 2/3 of the tooth length

A labially displaced anterior tooth is restored with a gold core porcelain jacket crown so that it is in line with the arch; the crown will appears: A. Short B. Long C. Narrow D. Wide

Description : A labially displaced anterior tooth is restored with a gold core porcelain jacket crown so that it is in line with the arch; the crown will appears: A. Short B. Long C. Narrow D. Wide

Last Answer : C. Narrow

In bridge work, which of the followings terms is NOT CORRECT: A. A retainer could be a crown to which a bridge is attached to B. A connector connects a pontic to a retainer or two retainers to each other C. The saddle is the area of the edentulous ridge over which the pontic will lie and comes in contact with pontic D. A pontic is an artificial tooth as part of a bridge

Description : In bridge work, which of the followings terms is NOT CORRECT: A. A retainer could be a crown to which a bridge is attached to B. A connector connects a pontic to a retainer or two retainers to each ... lie and comes in contact with pontic D. A pontic is an artificial tooth as part of a bridge

Last Answer : C. The saddle is the area of the edentulous ridge over which the pontic will lie and comes in contact with pontic

The minimal labial tooth reduction for satisfactory aesthetics with porcelain fused to metal crown is, A. 1mm B. The full thickness of enamel C. 1.5 mm D. 2.5mm E. One third of the dentine thickness

Description : The minimal labial tooth reduction for satisfactory aesthetics with porcelain fused to metal crown is, A. 1mm B. The full thickness of enamel C. 1.5 mm D. 2.5mm E. One third of the dentine thickness

Last Answer : C. 1.5 mm

A large amalgam core is to be condensed around several pins in a vital molar tooth; what type of amalgam mix would you prefer: A. A large mix to ensure homogeneity B. A large with extra mercury to give easier manipulative qualities C. Several small mixes, sequentially triturated D. Several small mixes with varying mercury/alloy ratios E. A basic mix to which additional mercury is added as needed

Description : A large amalgam core is to be condensed around several pins in a vital molar tooth; what type of amalgam mix would you prefer: A. A large mix to ensure homogeneity B. A large with ... small mixes with varying mercury/alloy ratios E. A basic mix to which additional mercury is added as needed

Last Answer : C. Several small mixes, sequentially triturated

The MOST effective manner to produce a hard surface on a cast is by: A. Employ as much water as possible on mixing B. Employ as little water as possible on mixing C. Adding 2% of borax to the mix D. Adding calcium tetraborate E. None of the above

Description : The MOST effective manner to produce a hard surface on a cast is by: A. Employ as much water as possible on mixing B. Employ as little water as possible on mixing C. Adding 2% of borax to the mix D. Adding calcium tetraborate E. None of the above

Last Answer : B. Employ as little water as possible on mixing

How would you treat hyperaemia (hyperaemic tooth):** A. Zinc Oxide and eugenol cement B. Calcium hydroxide C. Corticosteroid paste

Description : How would you treat hyperaemia (hyperaemic tooth):** A. Zinc Oxide and eugenol cement B. Calcium hydroxide C. Corticosteroid paste

Last Answer : A. Zinc Oxide and eugenol cement

The removable partial denture requires relining what would be the most appropriate action, A. take a new impression by asking the patient to occlude on it B. Provide equal space (maybe it was thickness) between denture and gingival tissues. C. Make sure the framework and retainers are seated in place before taking impression

Description : The removable partial denture requires relining what would be the most appropriate action, A. take a new impression by asking the patient to occlude on it B. Provide equal space (maybe it was ... gingival tissues. C. Make sure the framework and retainers are seated in place before taking impression

Last Answer : C. Make sure the framework and retainers are seated in place before taking impression

The MAIN purpose of burnishing is: A. To help eliminating excess mercury (condensing) B. To condense margins C. Polishing of filling

Description : The MAIN purpose of burnishing is: A. To help eliminating excess mercury (condensing) B. To condense margins C. Polishing of filling

Last Answer : B. To condense margins

A physician refers a nine years-old boy to you to confirm diagnosis. The boy has a fever of 40°C and coughing. When you focus your light into his eyes he turns away. Intra-orally there are white spots surrounded by red margins. The disease and lesions are: A. Measles and Koplik’s spots B. AHGS vesicles

Description : A physician refers a nine years-old boy to you to confirm diagnosis. The boy has a fever of 40°C and coughing. When you focus your light into his eyes he turns away. Intra-orally there are white ... by red margins. The disease and lesions are: A. Measles and Koplik's spots B. AHGS vesicles

Last Answer : A. Measles and Koplik’s spots

A patient is complaining of an open sore on the buccal mucosa. The lesion is painless, ulcerated, has indurated margins, 1.5 cm in diameter, covered by greyish-white exudate, enlarged lymph nodes and tender, negative tuberculin test and positive serology. The diagnosis is

Description : A patient is complaining of an open sore on the buccal mucosa. The lesion is painless, ulcerated, has  indurated margins, 1.5 cm in diameter, covered by greyish-white exudate, enlarged lymph nodes  and tender, negative tuberculin test and positive serology. The diagnosis is

Last Answer : Chancre /Primary lesion of syphilis 

Where is the retentive position on teeth according to the survey line: A. Below the height of contour B. Next to gingival margins

Description : Where is the retentive position on teeth according to the survey line: A. Below the height of contour B. Next to gingival margins

Last Answer : A. Below the height of contour

A major difference between light cured and chemical cured composite is that during setting or in function the light cured material tends to:******** VERY IMP A. Seal the margins better and completely B. Exhibit less wear on time C. Undergo greater colour change D. Shrink more rapidly E. Posses greater fracture toughness

Description : A major difference between light cured and chemical cured composite is that during setting or in function the light cured material tends to:******** VERY IMP A. Seal the margins better and ... on time C. Undergo greater colour change D. Shrink more rapidly E. Posses greater fracture toughness

Last Answer : D. Shrink more rapidly

Which of the following statement about the defective margins of amalgam restorations is true?+M07 A. The larger the breakdown, the greater the chance of decay. IF THERE IS MARGINAL BREAKDOWN THIS DOSNT NECESSITATE THE PRESENCE OF CARIES ALONG MARGIN So the ans is Chances are increased

Description : Which of the following statement about the defective margins of amalgam restorations is true?+M07 A. The larger the breakdown, the greater the chance of decay. IF THERE IS MARGINAL BREAKDOWN THIS DOSNT NECESSITATE THE PRESENCE OF CARIES ALONG MARGIN So the ans is Chances are increased

Last Answer : A. The larger the breakdown, the greater the chance of decay.

To minimize the load on a free-end saddle partial denture: (distal extension saddle) A. Use teeth with narrow Buccal-Lingual dimension B. Use mucco-compressive impression

Description : To minimize the load on a free-end saddle partial denture: (distal extension saddle) A. Use teeth with narrow Buccal-Lingual dimension B. Use mucco-compressive impression

Last Answer : B. Use mucco-compressive impression

How long should acrylic self-cure special trays been made prior to taking impression: A. 12 hrs B. Immediately after fabricating it C. After been left in water for an hour D. Wait for an hour before pouring

Description : How long should acrylic self-cure special trays been made prior to taking impression: A. 12 hrs B. Immediately after fabricating it C. After been left in water for an hour D. Wait for an hour before pouring

Last Answer : A. 12 hrs

The polysulfide rubber impression materials are: A. Not sensitive to temperature when curing B. Quite sensitive to temperature when curing C. Less sensitive to temperature than silicone rubber D. The same sensitivity to temperature as silicone rubber E. None of the above

Description : The polysulfide rubber impression materials are: A. Not sensitive to temperature when curing B. Quite sensitive to temperature when curing C. Less sensitive to temperature than silicone rubber D. The same sensitivity to temperature as silicone rubber E. None of the above

Last Answer : B. Quite sensitive to temperature when curing

Elastomers are:** A. Hydrophilic B. Hydrophobic C. Water-loving impression material D. Potassium alginates E. None of the above

Description : Elastomers are:** A. Hydrophilic B. Hydrophobic C. Water-loving impression material D. Potassium alginates E. None of the above

Last Answer : B. Hydrophobic

Dental impression materials are hydrocolloids of: A. The emulsoid type B. The suspension type C. The sol type D. The gel type E. None of the above

Description : Dental impression materials are hydrocolloids of: A. The emulsoid type B. The suspension type C. The sol type D. The gel type E. None of the above

Last Answer : A. The emulsoid type

The disadvantage of heating the impression compound in a water bath is: A. It may become brittle B. It may become grainy C. Lower moles with constituents are leached out D. The plasticity of the compound may be altered E. All of the above

Description : The disadvantage of heating the impression compound in a water bath is: A. It may become brittle B. It may become grainy C. Lower moles with constituents are leached out D. The plasticity of the compound may be altered E. All of the above

Last Answer : D. The plasticity of the compound may be altered

Fusion temperature of impression compound should occur: A. Below mouth temperature B. Above mouth temperature C. As of the skin temperature D. At the room temperature E. None of the above

Description : Fusion temperature of impression compound should occur: A. Below mouth temperature B. Above mouth temperature C. As of the skin temperature D. At the room temperature E. None of the above

Last Answer : B. Above mouth temperature

Which impression material should NOT be kept in water within on hour: (in another paper it was: 30 mins before pouring) A. Polyether B. Condensation silicone C. Polyvinyl silicone

Description : Which impression material should NOT be kept in water within on hour: (in another paper it was: 30  mins before pouring)  A. Polyether  B. Condensation silicone  C. Polyvinyl silicone 

Last Answer : A. Polyether 

Ledermix is used in RCT to relieve pain because of, A. Antibiotics B. Corticosteroid

Description : Ledermix is used in RCT to relieve pain because of, A. Antibiotics B. Corticosteroid

Last Answer : A. Antibiotics B. Corticosteroid

The major cause of jacket crown breakage is, A. Inclusion of platinum foil B. Use of weak cementum C. Voids of porcelain D. Porcelain is thinner than 1mm

Description : The major cause of jacket crown breakage is, A. Inclusion of platinum foil B. Use of weak cementum C. Voids of porcelain D. Porcelain is thinner than 1mm

Last Answer : D. Porcelain is thinner than 1mm

When should metallic framework not be contaminated during the fabrication of a porcelain fused to metal crown: A. Between bisque stage and glazing stage B. Between preheat and opaque stages C. Between opaque and bisque stages D. Between one opaque and two opaque stages

Description : When should metallic framework not be contaminated during the fabrication of a porcelain fused to metal crown: A. Between bisque stage and glazing stage B. Between preheat and opaque stages C. Between opaque and bisque stages D. Between one opaque and two opaque stages

Last Answer : B. Between preheat and opaque stages

A 8 years-old patient has 3 first premolars erupted and a swelling on the ridge of the un-erupted premolar. X ray shows a fully developed crown and ¾ roots development with no other pathology. What is your management: A. Remove the dentigerous cyst B. Soft tissues recision to allow eruption C. Soft tissues recision accompanied with orthodontic appliance to help with eruption

Description : A 8 years-old patient has 3 first premolars erupted and a swelling on the ridge of the un-erupted premolar. X ray shows a fully developed crown and ¾ roots development with no ... recision to allow eruption C. Soft tissues recision accompanied with orthodontic appliance to help with eruption

Last Answer : C. Soft tissues recision accompanied with orthodontic appliance to help with eruption

What statement is false: A. Not to survey when making the crown

Description : What statement is false: A. Not to survey when making the crown

Last Answer : A. Not to survey when making the crown

.Lateral canals are usually found at: A. The middle of the root B. First third of the root close to the crown C. The apical third

Description : .Lateral canals are usually found at: A. The middle of the root B. First third of the root close to the crown C. The apical third

Last Answer : C. The apical third

.When correction preparation for re contouring of occlusal surface is to be applied, grinding only of the adjusted surface: A. Should not be felt flat B. Requires a flat crown C. Requires no contact with adjacent teeth D. Should be felt flat

Description : .When correction preparation for re contouring of occlusal surface is to be applied, grinding only of the adjusted surface: A. Should not be felt flat B. Requires a flat crown C. Requires no contact with adjacent teeth D. Should be felt flat

Last Answer : A. Should not be felt flat

Which is the more retentive form for an anterior bridge A. ¾ partial veneer crown B. Class V inlay C. Pinlay Veneer D. Class III inlay with pins

Description : Which is the more retentive form for an anterior bridge A. ¾ partial veneer crown B. Class V inlay C. Pinlay Veneer D. Class III inlay with pins

Last Answer : A. ¾ partial veneer crown

When primary molars are prepared for stainless steel crowns, should the depth for reduction of the proximal surface be similar to the depth of the buccal and lingual surfaces? A. Yes; reduction of all wall is similar for best retention B. No, proximal reduction is greater to allow the crown to pass the contact area C. No, the buccal surfaces has the greatest reduction to remove the cervical bulge D. Yes, all undercuts are uniformly removed so that the steel crown can be seated E. No, because of lateral constriction, the lingual surface needs greatest reduction

Description : When primary molars are prepared for stainless steel crowns, should the depth for reduction of the proximal surface be similar to the depth of the buccal and lingual surfaces? A. Yes; reduction ... can be seated E. No, because of lateral constriction, the lingual surface needs greatest reduction

Last Answer : B. No, proximal reduction is greater to allow the crown to pass the contact area

How long would it take to notice significant reduction in radiolucency after finishing a root filling in a tooth with a periapical lesion: A. 6 months B. 1 month C. 3 months

Description : How long would it take to notice significant reduction in radiolucency after finishing a root filling in a tooth with a periapical lesion: A. 6 months B. 1 month C. 3 months

Last Answer : A. 6 months