Give detail classification of forging processes.

Give detail classification of forging processes. 
by

1 Answer

Answer :

Classification of forging processes : 

1.Open die forging:

a) Hand forging

b) Power forging:

 i. Hammer forging

 ii. Press forging

2.Close die forging:

a) Drop forging

b) Press forging

c) Machine forging
by

Related questions

State various advantages and limitations of forging processes.

Description : State various advantages and limitations of forging processes. 

Last Answer : Answer: Advantages of forging processes  1) Complex shaped parts can be forged 2) Mass production with greater accuracy is achieved. 3) It is very easy to maintain close tolerances. 4) ... cannot be produced by forging. 8) Rapid oxidation of metal surface at high temperature wears the dies 

Classify Forging processes.

Description : Classify Forging processes.

Last Answer : Classification of forging process - I. Open Die Forging: (a) Hand forging (b) Power forging: i. Hammer forging ii. Press forging Ii. Close Die Forging: (a) Drop forging (b) Press forging (c) Machine forging OR

Give detail classification of welding. State important factors upon which selection of welding process depends.

Description : Give detail classification of welding. State important factors upon which selection of welding process depends. 

Last Answer : Answer: Classification of Welding 1. Arc welding a. Carbon Arc Welding; b. Shielded Metal Arc Welding (SMAW) c. Submerged Arc Welding (SAW) d. Metal Inert Gas Welding (MIG, ... workers 14. Cost of materials 15. Code or specification requirements 16. Mechanical properties desired in joints 

Explain any two types of resistance welding processes in detail.

Description : Explain any two types of resistance welding processes in detail.

Last Answer : 1.Resistance Spot welding: Spot welding is employed to join overlapping strips, sheets or plates of metal at small areas. The pieces are assembled between two electrodes, which must possess high electrical ... small parts. Butt Welding provides joining with no loss of the welded materials.   

Draw flatter and Fuller. State its use in forging.

Description : Draw flatter and Fuller. State its use in forging.

Last Answer : 1. Fuller: Use of Fuller: Fuller is a forging tool, used to spread the metal. The fuller is placed against the metal stock, and then either the fuller or the stock is struck ... are used to give smoothness and accuracy to articles which have already been shaped by fullers and swages. 

Explain drop forging with neat sketch.

Description : Explain drop forging with neat sketch. 

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... [5] This energy will be delivered to the metal work-piece to produce plastic deformation.  

Describe briefly, hand forging and machine forging.

Description : Describe briefly, hand forging and machine forging. 

Last Answer : Hand Forging: [1] Hand forging is the oldest type of metal working process and has influenced the formation of other materials through the age. [2] Smith forging was formerly the process ... the height from which they fall, the higher will be intensity of blow the hammer will provide.

Write forging sequence for spanners.

Description : Write forging sequence for spanners.

Last Answer : Forging Sequence for Spanner: (1) The heated stock is elongated by reducing its cross section in first die. The operation is known as Fullering . (2) The metal is redistributed, increasing the cross ... . (5) Flash is removed. (6) Heat treatment and machining is done as per requirement. 

List any four applications of forging process.

Description : List any four applications of forging process. 

Last Answer : Applications of Forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Spanner 5. Alloy wheel 6. Differential gears 7. Drive shafts 8. Clutch hubs 9. Universal joints 10. Hand Tools

State any two advantages of forging process.

Description : State any two advantages of forging process. 

Last Answer : Advantages of forging processes: 1) Complex shaped parts can be forged 2) Mass production with greater accuracy is achieved. 3) It is very easy to maintain close tolerances. 4) ... highly skilled operator. 6) Better reproducibility. 7) Machining is not necessary to obtain final shape 

Classify forging. State Fullering

Description : Classify forging. State Fullering

Last Answer : Answer: Classification of forging processes 1.Open die forging: a) Hand forging b) Power forging: i. Hammer forging ii. Press forging 2.Close die forging: a) Drop forging b) ... The force is applied on the top fuller which results in decreasing the cross section at that point.  

Describe forging sequence for crank shaft.

Description : Describe forging sequence for crank shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging.   [2] After preliminary roll forging, stock ... the finished part is then trimmed in blanking die to remove excess metal or flash.   

Explain drop forging

Description : Explain drop forging

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... 5] This energy will be delivered to the metal work-piece to produce plastic deformation. 

Name forging defects.

Description : Name forging defects. 

Last Answer : 1. Cold shuts 2. Pitting 3. Die shift 4. Incomplete filling of dies 5. Dents 6. Flakes

Explain forging sequence for camshaft.

Description : Explain forging sequence for camshaft.

Last Answer : Forging process for manufacturing Camshaft: i) Stock is redistributed and size is increased at certain places & reduced at others by rolled forging. ii) after preliminary roll forging, the stock is ... v) finished part is trimmed in blanking die to remove excess metal or flash.

State the forging sequence for production of spanner.

Description : State the forging sequence for production of spanner.

Last Answer : Forging sequence for production of spanner Forging Sequence for Spanner: (1) The heated stock is elongated by reducing its cross section in first die. The operation is known as Fullering . (2) ... (5) Flash is removed. (6) Heat treatment and machining is done as per requirement.

Enlist any four operations carried out in forging process and explain fullering with neat sketch.

Description : Enlist any four operations carried out in forging process and explain fullering with neat sketch.

Last Answer : Operations carried out in forging process:  a) Upsetting b) Drawing Down c) Setting down d) Welding e) Bending f) Cutting g) Punching Fullering: In ... sledge hammer. The force is applied on the top fuller which results in decreasing the cross section at that point.

Enlist any four forging components.

Description : Enlist any four forging components.

Last Answer : Forging Components:  1. Connecting rod  2. Crankshaft  3. Camshaft  4. Alloy wheel  5. Drive shafts  6. Clutch hubs  7. Universal joints  8. Hand Tools

What are the steps in drop forging?

Description : What are the steps in drop forging? 

Last Answer : Drop Forging Process:  Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the ... . [5] This energy will be delivered to the metal work-piece to produce plastic deformation. 

Explain closed die forging with neat sketch

Description : Explain closed die forging with neat sketch

Last Answer : Impression die & Closed die forging process: Closed Die forging is also known as impression die forging. Close die forging process consist of specially prepared dies to manufacturing forged parts in large ... of accuracy. Complex shaped parts can be easily forged by this forging process.  

Enlist names of any four parts of automobile that can be manufactured by forging.

Description : Enlist names of any four parts of automobile that can be manufactured by forging.

Last Answer : Following are few automotive components that can be manufactured by forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Gears 5. Alloy wheel

Explain press forging with neat sketch.

Description : Explain press forging with neat sketch. 

Last Answer : Press Forging: In press forging, impression dies are used in which partd are made by plastically deforming a metal blank into die avities by slow squeezing action. The forging pressure builds up from the ... they are generally employed for non-ferrous alloys weighting from upto about 135 N. 

Differentiate between open die forging and close die forging.

Description : Differentiate between open die forging and close die forging.

Last Answer : Difference between open die and close die forging:

Explain forging process used to manufacture the spanners.

Description : Explain forging process used to manufacture the spanners. 

Last Answer : Answer: Forging process used for production of spanner: 1) Fullering -The heated stock is elongated by reducing its cross section in first die.  2) Edging- The metal is redistributed, ... Trimming: Flash is removed   (6) Heat treatment and machining is done as per requirement.   

Define forgeability. Name any two materials that are used in forging.

Description : Define forgeability. Name any two materials that are used in forging. 

Last Answer : Forgeability: Forgeability can be defined as the tolerance of a metal or alloy for deformation without failure. OR  Forgeability is defined as the ability of a metal to change size and shape when heated to ... 10) Tantalum alloys 11) Molybdenum alloys 12) Tungsten alloys 13) Beryllium.

(i) Compare Open Die Forging and Close Die Forging. (ii) Explain with neat sketch process of Drop Forging.

Description : (i) Compare Open Die Forging and Close Die Forging. (ii) Explain with neat sketch process of Drop Forging.

Last Answer : (i) Difference between Open Die and Close Die Forging: (ii)Drop Forging  Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop ... of upper and lower dies. The ram is fastened to the lower end of vertical hard wood board.

Draw the simple labeled sketches showing forging sequence for manufacturing Gears.

Description : Draw the simple labeled sketches showing forging sequence for manufacturing Gears.

Last Answer : Forging Sequence for Manufacturing Gears: i) The size of the heated stock is reduced with compensation of its length i.e. Upsetting is carried out.  ii) After heading or upsetting, stock is ... next impression or blocking die   iv) Then the finished part is trimmed in blanking die  

Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Description : Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging. [2] After preliminary roll forging, ... Then the finished part is then trimmed in blanking die to remove excess metal or flash.   

Compare drop forging and press forging.

Description : Compare drop forging and press forging. 

Last Answer : Comparison of Drop Forging and Press Forging: 

State four advantages and limitations of forging.

Description : State four advantages and limitations of forging.

Last Answer : Advantages of Forging: 1. Strength: i. Forging reduces the failures. ii. High strength to weight ratio. iii. It can be able to withstand fluctuating stress caused by sudden shock loading. ... be produced by forging. 8. Rapid oxidation of metal surface at high temperature wears the dies.

Explain the term ‘Draft’ related to forging.

Description : Explain the term ‘Draft’ related to forging.

Last Answer : Draft — The necessary taper on the side of a forging to allow removal from the dies; also applies to the die impression. Commonly expressed in degrees as the draft angle.

List the four hand tools used in forging.

Description : List the four hand tools used in forging.

Last Answer : Hand Tools used in Forging: 1. Hammer 2. Rigid Anvil 3. Hearth 4. Tong 5. Fuller

Give Classification of Presses.

Description : Give Classification of Presses.

Last Answer : 1. Classification on the basis of source of power. Manual Presses.  Mechanical presses. Hydraulic Presses. Pneumatic Presses. 2. Classification on the basis of number of slides. Single ... - Frame Presses. Gap Frame Presses. Straight Side Presses. Horn Presses. Inclibable Press

Give classification of tools used on turning centre.

Description : Give classification of tools used on turning centre. 

Last Answer : Classification of tools used on turning centre: A. On the Basis of Cutting Tool Construction (a) Solid tools. (b) Brazed tools. (c) Inserted bit tools. B. On the Basis of Cutting Tool Material (a) High ... (c) Cast alloy. (d) Cemented carbide. (e) Ceramics. (f) Boron Nitride. (g) Diamond. 

Give classification of welding process.

Description : Give classification of welding process.

Last Answer : Classification of Welding Process a. Arc welding 1) Carbon Arc Welding; 2) Shielded Metal Arc Welding (SMAW) 3) Submerged Arc Welding (SAW) 4) Metal Inert Gas Arc Welding (MIG, GMAW) 5) ... (USW) e. Thermit Welding (TW) f. Electron Beam Welding (EBW) g. Laser Welding (LW)

Name the various tools used in CNC turning centre. Explain any one in detail.

Description : Name the various tools used in CNC turning centre. Explain any one in detail.

Last Answer : Tools used on Turning Centre: 1. External Turning Tools: 2. Boring Bars:   3. Drills:   4. Threading Tools:   5. Parting Tools:   A. On the Basis of Cutting Tool Construction: ( ... (HCS). (c) Cast alloy. (d) Cemented carbide. (e) Ceramics. (f) Boron Nitride. (g) Diamond. 

Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Description : Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Last Answer : Working  : Shielded metal arc welding uses a metallic consumable electrode of a proper composition for generating arc between itself and the parent work piece. The molten electrode metal fills the weld ... . 2. Weld may contain slag inclusions 3. Fumes make difficult the process control.

List various surface finishing processes. Explain lapping.

Description : List various surface finishing processes. Explain lapping.

Last Answer : List of Surface Finishing Processes: [1] Grinding [2] Honing [3] Lapping [4] Burnishing [5] Buffing [6] Polishing Lapping Lapping is basically an abrasive process in which ... constantly changing. The effective path is of cycloid in nature. Figure shows the lapping process.  

Name various surface coating processes.

Description : Name various surface coating processes.

Last Answer : Surface coating process: (1) Metallic coating (2) Plastic coating (3) Organic coating (4) Inorganic coatings (5) Conversion coating (6) Other metal coating processes

List any four factors affecting selection of surface finishing processes.

Description : List any four factors affecting selection of surface finishing processes.

Last Answer : Following factors will affect the selection of surface finishing processes: 1. Material of component 2. Basic machining operation carried out on component 3. Dimensions of component 4. Final value (in µm) of machined surfaces 5. Application of machined surfaces 

List various surface cleaning processes.

Description : List various surface cleaning processes. 

Last Answer : Answer: Surface cleaning processes I. Chemical Cleaning a. Solution b. Saponification c. Emulsification d. Dispersion e. Aggregation Depending on cleaning fluids used, types of chemical ... . Power brushing e. Machine polishing & buffing III. Ultrasonic cleaning IV. Flame cleaning 

Classify welding processes.

Description : Classify welding processes.

Last Answer : Classification of Welding Process Depending on method of heat generation American welding society classifies welding as A. Arc Welding 1) Carbon Arc Welding; 2) Shielded Metal Arc Welding (SMAW) 3) ... . Thermit Welding (TW) F. Electron Beam Welding (EBW) G. Laser Welding (LW) 

List four mechanical and chemical cleaning processes.

Description : List four mechanical and chemical cleaning processes.

Last Answer : Chemical Cleaning: 1. Alkaline cleaning 2. Acid pickling 3. Electrolytic cleaning 4. Emulsified solvent cleaning 5. Vapour degreasing 6. Ultrasonic cleaning Mechanical Cleaning: a. ... b. Tumbling c. Barrel rolling d. Power brushing e. Machine polishing & buffing

Define Soldering. Give one application of soldering.

Description : Define Soldering. Give one application of soldering. 

Last Answer : Definition of Soldering:- Soldering is a method of uniting two or more piece of metal by means of a fusible alloy or metal, called solder, applied in the molten state. Applications of Soldering ... 9. Refrigeration and plumbing machine tools components,  10. Copper foil in stained glass work. 

Explain metal spraying process and give two applications.

Description : Explain metal spraying process and give two applications.

Last Answer : Metal praying of metalizing literally means to treat with or coat with a metal or metallic compound. Metalizing as a process normally includes the preparation of base material, the spraying on ... Its other applications are in having decorative films, reflecting surfaces and special metal forms. 

Give application of lapping, honing, buffing and burnishing.

Description : Give application of lapping, honing, buffing and burnishing.

Last Answer : Applications of Lapping: Press work dies, Moulding dies, Limit gauges, Surface plates, Engine valve and valve seat, Races of ball and roller bearings, Gears, Piston rings, Slip gauges, ... the surface. Burnishing components are Cam & followers, matting parts of engine, aesthetical components etc.

Sketch and label different types of gas welding flames. Also give application of any one flame.

Description : Sketch and label different types of gas welding flames. Also give application of any one flame.

Last Answer : 1) Neutral Flame: - A neutral flame is obtained when equal amounts of oxygen and acetylene are mixed and burnt in a torch.   Applications: - stainless steel, cast iron, copper ,mild ... when acetylene is supplied more than oxygen.   Applications:-high carbon steel, nonferrous alloy 

Define forgeability and give any four forgeable materials used to produce automotive components.

Description : Define forgeability and give any four forgeable materials used to produce automotive components.

Last Answer : Forgeability Forgeability can be defined as the tolerance of a metal or alloy for deformation without failure. OR Forgeability is defined as the ability of a metal to change size and shape when ... Columbium alloys 10) Tantalum alloys 11) Molybdenum alloys 12) Tungsten alloys 13) Beryllium.

Give the meaning of following ISO codes. 1) M02 2) M30 3) G90 4) G91

Description : Give the meaning of following ISO codes. 1) M02 2) M30 3) G90 4) G91

Last Answer : Meaning of ISO codes. 1) M02-Program end 2) M30-Program stop & Tape rewind 3) G90 :- Absolute Dimensioning 4) G91:- Incremental Dimensioning

Explain the working principle of galvanizing process. Give its applications also.

Description : Explain the working principle of galvanizing process. Give its applications also. 

Last Answer : Galvanization or galvanisation or galvanizing is the process of applying a protective zinc coating to steel or iron, to prevent rusting. The most common method is hot-dip galvanizing, in which parts are ... 5. All sort of containers 6. telegraph wire 7. fencing materials 8.Transformer parts