Classify Forging processes.

Classify Forging processes.
by

1 Answer

Answer :

Classification of forging process -

I. Open Die Forging: (a) Hand forging (b) Power forging: i. Hammer forging ii. Press forging

Ii. Close Die Forging: (a) Drop forging (b) Press forging (c) Machine forging

OR


image

by

Related questions

Classify forging. State Fullering

Description : Classify forging. State Fullering

Last Answer : Answer: Classification of forging processes 1.Open die forging: a) Hand forging b) Power forging: i. Hammer forging ii. Press forging 2.Close die forging: a) Drop forging b) ... The force is applied on the top fuller which results in decreasing the cross section at that point.  

Give detail classification of forging processes.

Description : Give detail classification of forging processes. 

Last Answer : Classification of forging processes :  1.Open die forging: a) Hand forging b) Power forging:  i. Hammer forging  ii. Press forging 2.Close die forging: a) Drop forging b) Press forging c) Machine forging

State various advantages and limitations of forging processes.

Description : State various advantages and limitations of forging processes. 

Last Answer : Answer: Advantages of forging processes  1) Complex shaped parts can be forged 2) Mass production with greater accuracy is achieved. 3) It is very easy to maintain close tolerances. 4) ... cannot be produced by forging. 8) Rapid oxidation of metal surface at high temperature wears the dies 

Classify welding processes.

Description : Classify welding processes.

Last Answer : Classification of Welding Process Depending on method of heat generation American welding society classifies welding as A. Arc Welding 1) Carbon Arc Welding; 2) Shielded Metal Arc Welding (SMAW) 3) ... . Thermit Welding (TW) F. Electron Beam Welding (EBW) G. Laser Welding (LW) 

Draw flatter and Fuller. State its use in forging.

Description : Draw flatter and Fuller. State its use in forging.

Last Answer : 1. Fuller: Use of Fuller: Fuller is a forging tool, used to spread the metal. The fuller is placed against the metal stock, and then either the fuller or the stock is struck ... are used to give smoothness and accuracy to articles which have already been shaped by fullers and swages. 

Explain drop forging with neat sketch.

Description : Explain drop forging with neat sketch. 

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... [5] This energy will be delivered to the metal work-piece to produce plastic deformation.  

Describe briefly, hand forging and machine forging.

Description : Describe briefly, hand forging and machine forging. 

Last Answer : Hand Forging: [1] Hand forging is the oldest type of metal working process and has influenced the formation of other materials through the age. [2] Smith forging was formerly the process ... the height from which they fall, the higher will be intensity of blow the hammer will provide.

Write forging sequence for spanners.

Description : Write forging sequence for spanners.

Last Answer : Forging Sequence for Spanner: (1) The heated stock is elongated by reducing its cross section in first die. The operation is known as Fullering . (2) The metal is redistributed, increasing the cross ... . (5) Flash is removed. (6) Heat treatment and machining is done as per requirement. 

List any four applications of forging process.

Description : List any four applications of forging process. 

Last Answer : Applications of Forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Spanner 5. Alloy wheel 6. Differential gears 7. Drive shafts 8. Clutch hubs 9. Universal joints 10. Hand Tools

State any two advantages of forging process.

Description : State any two advantages of forging process. 

Last Answer : Advantages of forging processes: 1) Complex shaped parts can be forged 2) Mass production with greater accuracy is achieved. 3) It is very easy to maintain close tolerances. 4) ... highly skilled operator. 6) Better reproducibility. 7) Machining is not necessary to obtain final shape 

Describe forging sequence for crank shaft.

Description : Describe forging sequence for crank shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging.   [2] After preliminary roll forging, stock ... the finished part is then trimmed in blanking die to remove excess metal or flash.   

Explain drop forging

Description : Explain drop forging

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... 5] This energy will be delivered to the metal work-piece to produce plastic deformation. 

Name forging defects.

Description : Name forging defects. 

Last Answer : 1. Cold shuts 2. Pitting 3. Die shift 4. Incomplete filling of dies 5. Dents 6. Flakes

Explain forging sequence for camshaft.

Description : Explain forging sequence for camshaft.

Last Answer : Forging process for manufacturing Camshaft: i) Stock is redistributed and size is increased at certain places & reduced at others by rolled forging. ii) after preliminary roll forging, the stock is ... v) finished part is trimmed in blanking die to remove excess metal or flash.

State the forging sequence for production of spanner.

Description : State the forging sequence for production of spanner.

Last Answer : Forging sequence for production of spanner Forging Sequence for Spanner: (1) The heated stock is elongated by reducing its cross section in first die. The operation is known as Fullering . (2) ... (5) Flash is removed. (6) Heat treatment and machining is done as per requirement.

Enlist any four operations carried out in forging process and explain fullering with neat sketch.

Description : Enlist any four operations carried out in forging process and explain fullering with neat sketch.

Last Answer : Operations carried out in forging process:  a) Upsetting b) Drawing Down c) Setting down d) Welding e) Bending f) Cutting g) Punching Fullering: In ... sledge hammer. The force is applied on the top fuller which results in decreasing the cross section at that point.

Enlist any four forging components.

Description : Enlist any four forging components.

Last Answer : Forging Components:  1. Connecting rod  2. Crankshaft  3. Camshaft  4. Alloy wheel  5. Drive shafts  6. Clutch hubs  7. Universal joints  8. Hand Tools

What are the steps in drop forging?

Description : What are the steps in drop forging? 

Last Answer : Drop Forging Process:  Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the ... . [5] This energy will be delivered to the metal work-piece to produce plastic deformation. 

Explain closed die forging with neat sketch

Description : Explain closed die forging with neat sketch

Last Answer : Impression die & Closed die forging process: Closed Die forging is also known as impression die forging. Close die forging process consist of specially prepared dies to manufacturing forged parts in large ... of accuracy. Complex shaped parts can be easily forged by this forging process.  

Enlist names of any four parts of automobile that can be manufactured by forging.

Description : Enlist names of any four parts of automobile that can be manufactured by forging.

Last Answer : Following are few automotive components that can be manufactured by forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Gears 5. Alloy wheel

Explain press forging with neat sketch.

Description : Explain press forging with neat sketch. 

Last Answer : Press Forging: In press forging, impression dies are used in which partd are made by plastically deforming a metal blank into die avities by slow squeezing action. The forging pressure builds up from the ... they are generally employed for non-ferrous alloys weighting from upto about 135 N. 

Differentiate between open die forging and close die forging.

Description : Differentiate between open die forging and close die forging.

Last Answer : Difference between open die and close die forging:

Explain forging process used to manufacture the spanners.

Description : Explain forging process used to manufacture the spanners. 

Last Answer : Answer: Forging process used for production of spanner: 1) Fullering -The heated stock is elongated by reducing its cross section in first die.  2) Edging- The metal is redistributed, ... Trimming: Flash is removed   (6) Heat treatment and machining is done as per requirement.   

Define forgeability. Name any two materials that are used in forging.

Description : Define forgeability. Name any two materials that are used in forging. 

Last Answer : Forgeability: Forgeability can be defined as the tolerance of a metal or alloy for deformation without failure. OR  Forgeability is defined as the ability of a metal to change size and shape when heated to ... 10) Tantalum alloys 11) Molybdenum alloys 12) Tungsten alloys 13) Beryllium.

(i) Compare Open Die Forging and Close Die Forging. (ii) Explain with neat sketch process of Drop Forging.

Description : (i) Compare Open Die Forging and Close Die Forging. (ii) Explain with neat sketch process of Drop Forging.

Last Answer : (i) Difference between Open Die and Close Die Forging: (ii)Drop Forging  Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop ... of upper and lower dies. The ram is fastened to the lower end of vertical hard wood board.

Draw the simple labeled sketches showing forging sequence for manufacturing Gears.

Description : Draw the simple labeled sketches showing forging sequence for manufacturing Gears.

Last Answer : Forging Sequence for Manufacturing Gears: i) The size of the heated stock is reduced with compensation of its length i.e. Upsetting is carried out.  ii) After heading or upsetting, stock is ... next impression or blocking die   iv) Then the finished part is trimmed in blanking die  

Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Description : Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging. [2] After preliminary roll forging, ... Then the finished part is then trimmed in blanking die to remove excess metal or flash.   

Compare drop forging and press forging.

Description : Compare drop forging and press forging. 

Last Answer : Comparison of Drop Forging and Press Forging: 

State four advantages and limitations of forging.

Description : State four advantages and limitations of forging.

Last Answer : Advantages of Forging: 1. Strength: i. Forging reduces the failures. ii. High strength to weight ratio. iii. It can be able to withstand fluctuating stress caused by sudden shock loading. ... be produced by forging. 8. Rapid oxidation of metal surface at high temperature wears the dies.

Explain the term ‘Draft’ related to forging.

Description : Explain the term ‘Draft’ related to forging.

Last Answer : Draft — The necessary taper on the side of a forging to allow removal from the dies; also applies to the die impression. Commonly expressed in degrees as the draft angle.

List the four hand tools used in forging.

Description : List the four hand tools used in forging.

Last Answer : Hand Tools used in Forging: 1. Hammer 2. Rigid Anvil 3. Hearth 4. Tong 5. Fuller

Classify butt welding process.

Description : Classify butt welding process.

Last Answer : Classification of Butt Welding Processes: 1. Flash Butt Welding 2. Resistance Butt Welding 3. Hand Welding 4. Upset Welding

Classify CNC machines.

Description : Classify CNC machines.

Last Answer : Classification of CNC machines. A. According to control loop feedback system: 1) Open - loop system 2) Closed - loop system B. According to type of tool motion control system: 1) Finite ... D. According to type of controller: 1) NC based controller system 2) CNC based controller system

Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Description : Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Last Answer : Working  : Shielded metal arc welding uses a metallic consumable electrode of a proper composition for generating arc between itself and the parent work piece. The molten electrode metal fills the weld ... . 2. Weld may contain slag inclusions 3. Fumes make difficult the process control.

List various surface finishing processes. Explain lapping.

Description : List various surface finishing processes. Explain lapping.

Last Answer : List of Surface Finishing Processes: [1] Grinding [2] Honing [3] Lapping [4] Burnishing [5] Buffing [6] Polishing Lapping Lapping is basically an abrasive process in which ... constantly changing. The effective path is of cycloid in nature. Figure shows the lapping process.  

Name various surface coating processes.

Description : Name various surface coating processes.

Last Answer : Surface coating process: (1) Metallic coating (2) Plastic coating (3) Organic coating (4) Inorganic coatings (5) Conversion coating (6) Other metal coating processes

List any four factors affecting selection of surface finishing processes.

Description : List any four factors affecting selection of surface finishing processes.

Last Answer : Following factors will affect the selection of surface finishing processes: 1. Material of component 2. Basic machining operation carried out on component 3. Dimensions of component 4. Final value (in µm) of machined surfaces 5. Application of machined surfaces 

Explain any two types of resistance welding processes in detail.

Description : Explain any two types of resistance welding processes in detail.

Last Answer : 1.Resistance Spot welding: Spot welding is employed to join overlapping strips, sheets or plates of metal at small areas. The pieces are assembled between two electrodes, which must possess high electrical ... small parts. Butt Welding provides joining with no loss of the welded materials.   

List various surface cleaning processes.

Description : List various surface cleaning processes. 

Last Answer : Answer: Surface cleaning processes I. Chemical Cleaning a. Solution b. Saponification c. Emulsification d. Dispersion e. Aggregation Depending on cleaning fluids used, types of chemical ... . Power brushing e. Machine polishing & buffing III. Ultrasonic cleaning IV. Flame cleaning 

List four mechanical and chemical cleaning processes.

Description : List four mechanical and chemical cleaning processes.

Last Answer : Chemical Cleaning: 1. Alkaline cleaning 2. Acid pickling 3. Electrolytic cleaning 4. Emulsified solvent cleaning 5. Vapour degreasing 6. Ultrasonic cleaning Mechanical Cleaning: a. ... b. Tumbling c. Barrel rolling d. Power brushing e. Machine polishing & buffing

Classify closed die forging. Explain any one with neat sketch.

Description : Classify closed die forging. Explain any one with neat sketch. 

Last Answer : Classification of closed / Impression die forging:- 1) drop forging 2) press forging 3) machine forging 4) Single die 5) Multi die close die forging :- Close die forging is also called as ... the first forging is made. after forging operation the part must be trimmed to remove the flash.

Sketch and describe the following press operations: 1. Punching 2. Shearing and 3. Trimming

Description : Sketch and describe the following press operations: 1. Punching 2. Shearing and 3. Trimming

Last Answer : (i) Punching : In punching operation, a hole is the desired result. The size of hole is determined by the size of punch and clearance is allowed on the die. The figure shows the ... still hot for maximum efficiency; therefore it is usually incorporated into the larger production process.

Describe with sketch the surface treatment process used to built-up worn out metal components of automotive engines.

Description : Describe with sketch the surface treatment process used to built-up worn out metal components of automotive engines.

Last Answer : Metal spraying is to build-up worn out metal components of automotive engines.   Metal Spraying of metalizing literally means to treat with or coat with a metal or metallic compound. Metalizing as ... being coated, by compressed air. A sectional view of metal spraying gun is shown in fig.  

Explain with sketch construction and application of progressive die.

Description : Explain with sketch construction and application of progressive die.

Last Answer : OR Construction A progressive die consists of the following parts.: 1. Stop 2. Sheet metal 3. Pilot 4. Blanking punch 5. Ram 6. Piercing punch 7. Stripper Plate 8. Die ... such as automotive, electronics and appliances. Example car brake caliper, washer, lid of a beverage can etc.

Explain the resistance spot welding process with neat sketch. State its two advantage and disadvantage.

Description : Explain the resistance spot welding process with neat sketch. State its two advantage and disadvantage. 

Last Answer : Resistance Spot welding: Spot welding is employed to join overlapping strips, sheets or plates of metal at small areas .The pieces are assembled between two electrodes, which must possess high electrical & thermal ... for making the RSW a success. 4. The thick jobs are not easy to weld. 

Draw neat labeled sketch of ply press.

Description : Draw neat labeled sketch of ply press.

Last Answer : sketch of ply press

Explain seam welding process with the help of neat sketch.

Description : Explain seam welding process with the help of neat sketch.

Last Answer : Seam Welding is a Resistance Welding (RW) process used for producing continuous joint of overlapping sheets by passing them between two rotating electrode wheels. Heat generated by the electric current flowing through ... the electrodes and cool the work rapidly to speed up the operation.    

List the materials used in press work for automobile components parts with example.

Description : List the materials used in press work for automobile components parts with example.

Last Answer : Materials used in press work: 1) Aluminium, 2) Copper, 3) Brass, 4) Mild Steel, 5) Galvanized iron (G.I) sheets, 6) Duralumin, 7) Y-alloys, 8) Naval Brass, 9) Cartridge Brass, ... 8) Carburettor bodies 9) Valves 10) Combustion Chamber 11) Cylinder heads , blocks,  12) Gear box cases

Explain the following press operations (a) Punching (b) Drawing

Description : Explain the following press operations (a) Punching (b) Drawing

Last Answer : a) Punching: In punching operation, a hole is the desired result. The size of hole is determined by the size of punch and clearance is allowed on the die. The figure shows the spacing of hole on plate2 ... between punch and die is greater. [5] The drawing operation is illustrated in Fig.  

State the meaning of G90, G91.

Description : State the meaning of G90, G91.

Last Answer : Meaning of following G-Codes: G90 :- Absolute Dimensioning G91:- Incremental Dimensioning