State any two advantages of forging process.

State any two advantages of forging process. 
by

1 Answer

Answer :

Advantages of forging processes:

1) Complex shaped parts can be forged

2) Mass production with greater accuracy is achieved.

3) It is very easy to maintain close tolerances.

4) Relatively good utilization of materials.

5) Does not require highly skilled operator.

6) Better reproducibility.

7) Machining is not necessary to obtain final shape 
by

Related questions

State various advantages and limitations of forging processes.

Description : State various advantages and limitations of forging processes. 

Last Answer : Answer: Advantages of forging processes  1) Complex shaped parts can be forged 2) Mass production with greater accuracy is achieved. 3) It is very easy to maintain close tolerances. 4) ... cannot be produced by forging. 8) Rapid oxidation of metal surface at high temperature wears the dies 

State four advantages and limitations of forging.

Description : State four advantages and limitations of forging.

Last Answer : Advantages of Forging: 1. Strength: i. Forging reduces the failures. ii. High strength to weight ratio. iii. It can be able to withstand fluctuating stress caused by sudden shock loading. ... be produced by forging. 8. Rapid oxidation of metal surface at high temperature wears the dies.

List any four applications of forging process.

Description : List any four applications of forging process. 

Last Answer : Applications of Forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Spanner 5. Alloy wheel 6. Differential gears 7. Drive shafts 8. Clutch hubs 9. Universal joints 10. Hand Tools

Enlist any four operations carried out in forging process and explain fullering with neat sketch.

Description : Enlist any four operations carried out in forging process and explain fullering with neat sketch.

Last Answer : Operations carried out in forging process:  a) Upsetting b) Drawing Down c) Setting down d) Welding e) Bending f) Cutting g) Punching Fullering: In ... sledge hammer. The force is applied on the top fuller which results in decreasing the cross section at that point.

Explain forging process used to manufacture the spanners.

Description : Explain forging process used to manufacture the spanners. 

Last Answer : Answer: Forging process used for production of spanner: 1) Fullering -The heated stock is elongated by reducing its cross section in first die.  2) Edging- The metal is redistributed, ... Trimming: Flash is removed   (6) Heat treatment and machining is done as per requirement.   

(i) Compare Open Die Forging and Close Die Forging. (ii) Explain with neat sketch process of Drop Forging.

Description : (i) Compare Open Die Forging and Close Die Forging. (ii) Explain with neat sketch process of Drop Forging.

Last Answer : (i) Difference between Open Die and Close Die Forging: (ii)Drop Forging  Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop ... of upper and lower dies. The ram is fastened to the lower end of vertical hard wood board.

Draw flatter and Fuller. State its use in forging.

Description : Draw flatter and Fuller. State its use in forging.

Last Answer : 1. Fuller: Use of Fuller: Fuller is a forging tool, used to spread the metal. The fuller is placed against the metal stock, and then either the fuller or the stock is struck ... are used to give smoothness and accuracy to articles which have already been shaped by fullers and swages. 

Classify forging. State Fullering

Description : Classify forging. State Fullering

Last Answer : Answer: Classification of forging processes 1.Open die forging: a) Hand forging b) Power forging: i. Hammer forging ii. Press forging 2.Close die forging: a) Drop forging b) ... The force is applied on the top fuller which results in decreasing the cross section at that point.  

State the forging sequence for production of spanner.

Description : State the forging sequence for production of spanner.

Last Answer : Forging sequence for production of spanner Forging Sequence for Spanner: (1) The heated stock is elongated by reducing its cross section in first die. The operation is known as Fullering . (2) ... (5) Flash is removed. (6) Heat treatment and machining is done as per requirement.

Define forgeability. Name any two materials that are used in forging.

Description : Define forgeability. Name any two materials that are used in forging. 

Last Answer : Forgeability: Forgeability can be defined as the tolerance of a metal or alloy for deformation without failure. OR  Forgeability is defined as the ability of a metal to change size and shape when heated to ... 10) Tantalum alloys 11) Molybdenum alloys 12) Tungsten alloys 13) Beryllium.

Explain drop forging with neat sketch.

Description : Explain drop forging with neat sketch. 

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... [5] This energy will be delivered to the metal work-piece to produce plastic deformation.  

Describe briefly, hand forging and machine forging.

Description : Describe briefly, hand forging and machine forging. 

Last Answer : Hand Forging: [1] Hand forging is the oldest type of metal working process and has influenced the formation of other materials through the age. [2] Smith forging was formerly the process ... the height from which they fall, the higher will be intensity of blow the hammer will provide.

Write forging sequence for spanners.

Description : Write forging sequence for spanners.

Last Answer : Forging Sequence for Spanner: (1) The heated stock is elongated by reducing its cross section in first die. The operation is known as Fullering . (2) The metal is redistributed, increasing the cross ... . (5) Flash is removed. (6) Heat treatment and machining is done as per requirement. 

Describe forging sequence for crank shaft.

Description : Describe forging sequence for crank shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging.   [2] After preliminary roll forging, stock ... the finished part is then trimmed in blanking die to remove excess metal or flash.   

Explain drop forging

Description : Explain drop forging

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... 5] This energy will be delivered to the metal work-piece to produce plastic deformation. 

Name forging defects.

Description : Name forging defects. 

Last Answer : 1. Cold shuts 2. Pitting 3. Die shift 4. Incomplete filling of dies 5. Dents 6. Flakes

Explain forging sequence for camshaft.

Description : Explain forging sequence for camshaft.

Last Answer : Forging process for manufacturing Camshaft: i) Stock is redistributed and size is increased at certain places & reduced at others by rolled forging. ii) after preliminary roll forging, the stock is ... v) finished part is trimmed in blanking die to remove excess metal or flash.

Enlist any four forging components.

Description : Enlist any four forging components.

Last Answer : Forging Components:  1. Connecting rod  2. Crankshaft  3. Camshaft  4. Alloy wheel  5. Drive shafts  6. Clutch hubs  7. Universal joints  8. Hand Tools

What are the steps in drop forging?

Description : What are the steps in drop forging? 

Last Answer : Drop Forging Process:  Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the ... . [5] This energy will be delivered to the metal work-piece to produce plastic deformation. 

Explain closed die forging with neat sketch

Description : Explain closed die forging with neat sketch

Last Answer : Impression die & Closed die forging process: Closed Die forging is also known as impression die forging. Close die forging process consist of specially prepared dies to manufacturing forged parts in large ... of accuracy. Complex shaped parts can be easily forged by this forging process.  

Enlist names of any four parts of automobile that can be manufactured by forging.

Description : Enlist names of any four parts of automobile that can be manufactured by forging.

Last Answer : Following are few automotive components that can be manufactured by forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Gears 5. Alloy wheel

Explain press forging with neat sketch.

Description : Explain press forging with neat sketch. 

Last Answer : Press Forging: In press forging, impression dies are used in which partd are made by plastically deforming a metal blank into die avities by slow squeezing action. The forging pressure builds up from the ... they are generally employed for non-ferrous alloys weighting from upto about 135 N. 

Give detail classification of forging processes.

Description : Give detail classification of forging processes. 

Last Answer : Classification of forging processes :  1.Open die forging: a) Hand forging b) Power forging:  i. Hammer forging  ii. Press forging 2.Close die forging: a) Drop forging b) Press forging c) Machine forging

Differentiate between open die forging and close die forging.

Description : Differentiate between open die forging and close die forging.

Last Answer : Difference between open die and close die forging:

Draw the simple labeled sketches showing forging sequence for manufacturing Gears.

Description : Draw the simple labeled sketches showing forging sequence for manufacturing Gears.

Last Answer : Forging Sequence for Manufacturing Gears: i) The size of the heated stock is reduced with compensation of its length i.e. Upsetting is carried out.  ii) After heading or upsetting, stock is ... next impression or blocking die   iv) Then the finished part is trimmed in blanking die  

Classify Forging processes.

Description : Classify Forging processes.

Last Answer : Classification of forging process - I. Open Die Forging: (a) Hand forging (b) Power forging: i. Hammer forging ii. Press forging Ii. Close Die Forging: (a) Drop forging (b) Press forging (c) Machine forging OR

Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Description : Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging. [2] After preliminary roll forging, ... Then the finished part is then trimmed in blanking die to remove excess metal or flash.   

Compare drop forging and press forging.

Description : Compare drop forging and press forging. 

Last Answer : Comparison of Drop Forging and Press Forging: 

Explain the term ‘Draft’ related to forging.

Description : Explain the term ‘Draft’ related to forging.

Last Answer : Draft — The necessary taper on the side of a forging to allow removal from the dies; also applies to the die impression. Commonly expressed in degrees as the draft angle.

List the four hand tools used in forging.

Description : List the four hand tools used in forging.

Last Answer : Hand Tools used in Forging: 1. Hammer 2. Rigid Anvil 3. Hearth 4. Tong 5. Fuller

State advantages and limitations of honing process.

Description : State advantages and limitations of honing process. 

Last Answer : Advantages: 1. Less complex or low cost fixtures. 2. It is highly accurate. 3. It can be used for both long and short bores. 4. It maintains original bore centerline. 5. Any ... rotated or supported. If the workpiece is thin, even hand pressure may cause a slightly oval hole. 

Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Description : Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Last Answer : Working  : Shielded metal arc welding uses a metallic consumable electrode of a proper composition for generating arc between itself and the parent work piece. The molten electrode metal fills the weld ... . 2. Weld may contain slag inclusions 3. Fumes make difficult the process control.

State advantages of CNC over NC.

Description : State advantages of CNC over NC.

Last Answer : Advantages of CNC over NC 1. Complex machining operations can be easily done. 2. It requires less inspection. 3. It reduces scrap & waste. 4. It gives high production rate. 5. ... is available in CNC lathe which gives idea about job. This feature is not available in conventional machine 

State the various advantages and limitations of CNC machine.

Description : State the various advantages and limitations of CNC machine. 

Last Answer : Advantages of CNC Machines:-  [1] Greater machine utilization. [2] Complex machining operations can be easily done. [3] It gives high degree of accuracy. [4] It requires less inspection. [5] ... tooling cost. 6) Temperature, humidity & dust must be affect machining. 7) Initial cost is high. 

State four advantages of CNC machines over conventional machines.

Description : State four advantages of CNC machines over conventional machines.

Last Answer : Advantages of CNC machines over conventional machines: 1) Greater machine utilization. 2) Complex machining operations can be easily done. 3) It gives high degree of accuracy. 4) It requires less ... is reduced. 15) Elimination of special jigs and fixtures. 16) Accurate costing & scheduling. 

State four advantages of welding.

Description : State four advantages of welding.

Last Answer : Advantages of Welding Process: 1) It produce permanent joint. 2) Large number of metals can be welded. 3) Freedom in design. 4) Strong and tight joining 5) Cost effectiveness 6) Simplicity of welded structures design 7) Welding processes may be mechanized and automated.

Explain the resistance spot welding process with neat sketch. State its two advantage and disadvantage.

Description : Explain the resistance spot welding process with neat sketch. State its two advantage and disadvantage. 

Last Answer : Resistance Spot welding: Spot welding is employed to join overlapping strips, sheets or plates of metal at small areas .The pieces are assembled between two electrodes, which must possess high electrical & thermal ... for making the RSW a success. 4. The thick jobs are not easy to weld. 

State “Plane washer” making process with use of combination die.

Description : State “Plane washer” making process with use of combination die.

Last Answer : (Note: The plain washers can be produced by using Compound die or Progressive die. It is not possible to use combination die for making plain washers, so consider compound die or progressive die for answer. ... Stop 2.sheet metal 3.pilot 4.blanking punch 5.ram 6.piercing punch 7.stripper 8.die

Give detail classification of welding. State important factors upon which selection of welding process depends.

Description : Give detail classification of welding. State important factors upon which selection of welding process depends. 

Last Answer : Answer: Classification of Welding 1. Arc welding a. Carbon Arc Welding; b. Shielded Metal Arc Welding (SMAW) c. Submerged Arc Welding (SAW) d. Metal Inert Gas Welding (MIG, ... workers 14. Cost of materials 15. Code or specification requirements 16. Mechanical properties desired in joints 

Explain metal spraying process and give two applications.

Description : Explain metal spraying process and give two applications.

Last Answer : Metal praying of metalizing literally means to treat with or coat with a metal or metallic compound. Metalizing as a process normally includes the preparation of base material, the spraying on ... Its other applications are in having decorative films, reflecting surfaces and special metal forms. 

Describe buffing process and enlist its any two applications.

Description : Describe buffing process and enlist its any two applications.

Last Answer : Buffing process :- Buffing is used to give a much higher, lustrous, reflective finish that cannot be obtained by polishing. The buffing process consists in applying very fine abrasives with ... , tools, store fixtures, commercial and residential hardware and household utensils and appliances.

Define soldering process and enlist any two applications.

Description : Define soldering process and enlist any two applications.

Last Answer : Soldering: Soldering is a method of joining two or more piece of metal by means of a fusible alloy or metal, called solder, applied in the molten state. Applications: 1. Circuitry ... gutters, 9. Refrigeration and plumbing machine tools components, 10. Copper foil in stained glass work.

Describe with sketch the surface treatment process used to built-up worn out metal components of automotive engines.

Description : Describe with sketch the surface treatment process used to built-up worn out metal components of automotive engines.

Last Answer : Metal spraying is to build-up worn out metal components of automotive engines.   Metal Spraying of metalizing literally means to treat with or coat with a metal or metallic compound. Metalizing as ... being coated, by compressed air. A sectional view of metal spraying gun is shown in fig.  

Explain seam welding process with the help of neat sketch.

Description : Explain seam welding process with the help of neat sketch.

Last Answer : Seam Welding is a Resistance Welding (RW) process used for producing continuous joint of overlapping sheets by passing them between two rotating electrode wheels. Heat generated by the electric current flowing through ... the electrodes and cool the work rapidly to speed up the operation.    

Explain buffing process with neat sketch.

Description : Explain buffing process with neat sketch. 

Last Answer : Buffing process :- Buffing is used to give a much higher, lustrous, reflective finish that cannot be obtained by polishing. The buffing process consists in applying very fine ... sporting items, tools, store fixtures, commercial and residential hardware and household utensils and appliances. 

List common equipments used for arc welding process.

Description : List common equipments used for arc welding process.

Last Answer : 1. A.C. or D.C. machine 2. Electrode (bare or coated) 3. Electrode Holder 4. Cables and its connectors 5. Chipping Hammer 6. Earthing Clamps 7. Wire-brush 8. Helmet 9. Safety Goggles 10. Hand Gloves 11. Apron Sleeves etc.

Classify butt welding process.

Description : Classify butt welding process.

Last Answer : Classification of Butt Welding Processes: 1. Flash Butt Welding 2. Resistance Butt Welding 3. Hand Welding 4. Upset Welding

Differentiate between lapping and honing process.

Description : Differentiate between lapping and honing process.

Last Answer : S. N. Lapping Honing 1 Lapping is a finishing process in which tool used is called lap. Honing is a finishing process in which tool used is called ... level. Used to improve certain form characteristics such as cylindricity, surface finish, or sphericity.

Differentiate with acid cleaning and alkaline cleaning process.

Description : Differentiate with acid cleaning and alkaline cleaning process. 

Last Answer : Acid Cleaning Process Alkaline Cleaning Process 1 Acid cleaning is used for removal of light rust, tarnish, scale, drawing compounds, oil, and grease It is used for the ... .  caustic soda, tri-sodium phosphate, silicates, borates, or carbonates are the alkaline agents.

Explain electroplating process

Description : Explain electroplating process

Last Answer : Electroplating Process: Electroplating may be described as a process of covering a surface or object usually metallic with a thin adherent coating of same or other metal by electrolysis. The form of ... wear. Gold, silver and platinum plating are used in jewellery and electronic industry.