How many inches is .40mm?

How many inches is .40mm?
by

1 Answer

Answer :

0.015748 inches
by

Related questions

square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?

Description : square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?

Last Answer : 10001/999900

If a contractor proposes to increase concrete cover beyond contractual specification (i.e. 40mm to 70mm), shall engineers accept the proposal?

Description : If a contractor proposes to increase concrete cover beyond contractual specification (i.e. 40mm to 70mm), shall engineers accept the proposal?

Last Answer : In contractual aspect, based on the requirement of General Specification of Civil Engineering Works (1992 Edition), the tolerance of concrete cover is between + ... larger cover. Therefore, with an increase of concrete cover, the crack width will increase which is undesirable.

If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Last Answer : b) 40/9

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm

Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse aggregate should not exceed one fifty of the minimum dimension of the reinforced concrete member (c)The aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Description : Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse ... aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Last Answer : (d) All the above

For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm

Description : For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm

Last Answer : (a) 40mm

The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm

Description : The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm

Last Answer : (c) 50mm

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links