Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse aggregate should not exceed one fifty of the minimum dimension of the reinforced concrete member (c)The aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Which of the following statement is correct
(a) The maximum size of coarse aggregate should not exceed one fourth of the minimum
dimension of the plain concrete member.
(b) The maximum size of coarse aggregate should not exceed one fifty of the minimum
dimension of the reinforced concrete member
(c)The aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works
(d) All the above
by

1 Answer

Answer :

(d) All the above
by

Related questions

In designing concrete structures, normally maximum aggregate sizes are adopted with ranges from 10mm to 20mm. Does an increase of maximum aggregate size benefit the structures?

Description : In designing concrete structures, normally maximum aggregate sizes are adopted with ranges from 10mm to 20mm. Does an increase of maximum aggregate size benefit the structures?

Last Answer : To answer this question, let's consider an example of a cube. The surface area to volume ratio of a cube is 6/b where b is the length of the cube. This implies that ... requirement can offset the disadvantages brought about by discontinuities as suggested by Longman Scientific and Technical (1987).

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm

Description : If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm

Last Answer : Answer: Option C

For ensuring quality of concrete, use (A) Single sized aggregates (B) Two sized aggregate (C) Graded aggregates (D) Coarse aggregates

Description : For ensuring quality of concrete, use (A) Single sized aggregates (B) Two sized aggregate (C) Graded aggregates (D) Coarse aggregates

Last Answer : (C) Graded aggregates

Pick up the correct statement from the following: (A) The maximum size of a coarse aggregate, is 75 mm and minimum 4.75 mm (B) The maximum size of the fine aggregate, is 4.75 mm and minimum 0.075 mm (C) The material having particles of size varying from 0.06 mm to 0.002 mm, is known as silt (D) All the ab

Description : Pick up the correct statement from the following: (A) The maximum size of a coarse aggregate, is 75 mm and minimum 4.75 mm (B) The maximum size of the fine aggregate, is 4.75 mm and minimum 0.075 mm ( ... having particles of size varying from 0.06 mm to 0.002 mm, is known as silt (D) All the ab

Last Answer : Answer: Option D

Columns may be made of plain concrete if their unsupported lengths do not exceed their least lateral dimension (A) Two times (B) Three times (C) Four times (D) Five times

Description : Columns may be made of plain concrete if their unsupported lengths do not exceed their least lateral dimension (A) Two times (B) Three times (C) Four times (D) Five times

Last Answer : Answer: Option C

If the engineer-in-charge approves, the 10 cm cubes may be used for the work test of concrete provided maximum nominal size of aggregate, does not exceed (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Description : If the engineer-in-charge approves, the 10 cm cubes may be used for the work test of concrete provided maximum nominal size of aggregate, does not exceed (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option C

The percentage of the aggregate of F.M. 2.6 to be combined with coarse aggregate of F.M. 6.8 for obtaining the aggregates of F.M. 5.4, is (A) 30 % (B) 40 % (C) 50 % (D) 60 %

Description : The percentage of the aggregate of F.M. 2.6 to be combined with coarse aggregate of F.M. 6.8 for obtaining the aggregates of F.M. 5.4, is (A) 30 % (B) 40 % (C) 50 % (D) 60 %

Last Answer : (C) 50 %

For preparing a test-specimen, it is necessary (A) To mix cement and fine aggregate by dry hand (B) To mix coarse aggregates (C) To mix water to the cement, fine aggregates and coarse aggregates (D) All the above

Description : For preparing a test-specimen, it is necessary (A) To mix cement and fine aggregate by dry hand (B) To mix coarse aggregates (C) To mix water to the cement, fine aggregates and coarse aggregates (D) All the above

Last Answer : Answer: Option D

Index number expressing the relative sizes of both coarse and fine aggregates, is called (A) Proportioning of aggregates (B) Fineness modulus (C) Grading of aggregates (D) None of these

Description : Index number expressing the relative sizes of both coarse and fine aggregates, is called (A) Proportioning of aggregates (B) Fineness modulus (C) Grading of aggregates (D) None of these

Last Answer : Answer: Option B

For reinforced concrete work, aggregates having a nominal size of -------- are generally used [ A ] 20 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Description : For reinforced concrete work, aggregates having a nominal size of -------- are generally used [ A ] 20 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Last Answer : [ A ] 20 mm

To ensure constant moisture content in aggregates (A) Area of each aggregate pile should be large (B) Height of each aggregate pile should not exceed 1.50 m (C) Aggregate pile should be left for 24 hours before aggregates are used (D) All the above

Description : To ensure constant moisture content in aggregates (A) Area of each aggregate pile should be large (B) Height of each aggregate pile should not exceed 1.50 m (C) Aggregate pile should be left for 24 hours before aggregates are used (D) All the above

Last Answer : Answer: Option D

For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm

Description : For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm

Last Answer : (a) 40mm

Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by a straight horizontal line on the grading curve (C) The omission of a certain size of aggregate in concrete increases the workability but also increases the liability to segregation (D) All the above

Description : Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by ... in concrete increases the workability but also increases the liability to segregation (D) All the above

Last Answer : Answer: Option D

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned

Description : A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

Last Answer : A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is 200µNm

If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Last Answer : b) 40/9

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

Which of the following represents a carpet of sand-bitumen mix without coarse aggregates? (A) Mastic asphalt (B) Sheet asphalt (C) Bituminous carpet (D) Bituminous concrete

Description : Which of the following represents a carpet of sand-bitumen mix without coarse aggregates? (A) Mastic asphalt (B) Sheet asphalt (C) Bituminous carpet (D) Bituminous concrete

Last Answer : Answer: Option B

If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Description : If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Last Answer : Answer: Option C

Internal friction between the ingredients of concrete, is decreased by using (A) Less water (B) Fine aggregates (C) Rich mix (D) More water and coarse aggregates

Description : Internal friction between the ingredients of concrete, is decreased by using (A) Less water (B) Fine aggregates (C) Rich mix (D) More water and coarse aggregates

Last Answer : Answer: Option D

Concrete gains strength due to (A) Chemical reaction of cement with sand and coarse aggregates (B) Evaporation of water from concrete (C) Hydration of cement (D) All the above

Description : Concrete gains strength due to (A) Chemical reaction of cement with sand and coarse aggregates (B) Evaporation of water from concrete (C) Hydration of cement (D) All the above

Last Answer : Answer: Option C

The internal friction between the ingredients to concrete is minimized by (a) Adopting coarse aggregates (b) Using more water (c) Reducing the surface area (d) All of these

Description : The internal friction between the ingredients to concrete is minimized by (a) Adopting coarse aggregates (b) Using more water (c) Reducing the surface area (d) All of these

Last Answer : (d) All of these

The proportion of coarse aggregates to fire aggregates in structural concrete is usually [ A ] 0.50 - 1.25 [ B ] 1.25 - 4.50 [ C ] 1.50 - 2.50 [ D ] 0.25 - 0.75

Description : The proportion of coarse aggregates to fire aggregates in structural concrete is usually [ A ] 0.50 - 1.25 [ B ] 1.25 - 4.50 [ C ] 1.50 - 2.50 [ D ] 0.25 - 0.75

Last Answer : [ C ] 1.50 - 2.50

Concrete gains strength due to [ A ] Chemical reaction of cement with sand and coarse aggregates [ B ] Evaporation of water from concrete [ C ] Hydration of cement [ D ] All the above

Description : Concrete gains strength due to [ A ] Chemical reaction of cement with sand and coarse aggregates [ B ] Evaporation of water from concrete [ C ] Hydration of cement [ D ] All the above

Last Answer : [ C ] Hydration of cement

As per IS: 456-2000, the maximum size of aggregate is [ A ] 1/4 of maximum thickness of member [ B ] 1/4 of minimum thickness of member [ C ] 1/5 of maximum thickness of member [ D ] 1/5 of minimum thickness of member

Description : As per IS: 456-2000, the maximum size of aggregate is [ A ] 1/4 of maximum thickness of member [ B ] 1/4 of minimum thickness of member [ C ] 1/5 of maximum thickness of member [ D ] 1/5 of minimum thickness of member

Last Answer : [ B ] 1/4 of minimum thickness of member

The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Description : The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Last Answer : Answer: Option A

Workability of concrete for a given water content is good if the aggregates, are (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregate

Description : Workability of concrete for a given water content is good if the aggregates, are (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregate

Last Answer : Answer: Option A

If P, Y and Z are the weights of cement, fine aggregates and coarse aggregates respectively and W/C is the water cement ratio, the minimum quantity of water to be added to first batch, is obtained by the equation (A) 0.1P + 0.3Y + 0.1Z = W/C × P (B) 0.3P + 0.1Y + 0.01Z = W/C × P (C) 0.4P + 0.2Y + 0.01Z = W/C × P (D) 0.5P + 0.3Y + 0.01Z = W/C × P

Description : If P, Y and Z are the weights of cement, fine aggregates and coarse aggregates respectively and W/C is the water cement ratio, the minimum quantity of water to be added to first batch, is obtained by the equation (A) 0.1P + 0.3Y + 0. ... + 0.2Y + 0.01Z = W/C P (D) 0.5P + 0.3Y + 0.01Z = W/C P

Last Answer : Answer: Option B

For reinforced concrete, the aggregate used is (a) Sand (b) Gravel (c) Crushed rock (d) All of these

Description : For reinforced concrete, the aggregate used is (a) Sand (b) Gravel (c) Crushed rock (d) All of these

Last Answer : (d) All of these

Pick up the correct statement from the following: (A) The ratio of total volume of voids in soil aggregates to the total volume of aggregate, is called Porosity (B) Water retained by the interstices due to molecular attraction, is called pellicular water (C) Sum of the percentage of specific yield and specific retention is 100 (D) All the above

Description : Pick up the correct statement from the following: (A) The ratio of total volume of voids in soil aggregates to the total volume of aggregate, is called Porosity (B) Water retained by the interstices ... (C) Sum of the percentage of specific yield and specific retention is 100 (D) All the above

Last Answer : Answer: Option D

A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on the column, should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Last Answer : Answer: Option B

According to IS Code , the requirement of an ordinary Portland cement is (a) The residue does not exceed 10% when sieved through is sieve no .9 (b) Its initial setting time is not less than 30 minutes. (c) its expansion is not morethan 10mm for unaerated cement (d) All the above.

Description : According to IS Code , the requirement of an ordinary Portland cement is (a) The residue does not exceed 10% when sieved through is sieve no .9 (b) Its initial setting time is not less than 30 minutes. (c) its expansion is not morethan 10mm for unaerated cement (d) All the above.

Last Answer : (d) All the above.

The maximum amount of dust which may be permitted in aggregates is (A) 5% of the total aggregates for low workability with a coarse grading (B) 10% of the total aggregates for low workability with a fine grading (C) 20% of the total aggregates for a mix having high workability with fine grading (D) All the above

Description : The maximum amount of dust which may be permitted in aggregates is (A) 5% of the total aggregates for low workability with a coarse grading (B) 10% of the total aggregates for low workability with ... of the total aggregates for a mix having high workability with fine grading (D) All the above

Last Answer : Answer: Option D

Illustrate the effect of properties of coarse aggregates on compressive strength of concrete.

Description : Illustrate the effect of properties of coarse aggregates on compressive strength of concrete.

Last Answer : Effect of properties of coarse aggregates on compressive strength of concrete. i. Size of aggregate: If coarse aggregate particles are of large size (say 20 mm) in concrete mixture , then ... of strength. But if water absorption is less concrete becomes as per proportion giving required strength.

The void ratio of (A) Single size coarse aggregate is roughly 0.45 (B) Graded coarse aggregate is roughly 0.040 (C) Fine aggregate is roughly 0.45 (D) All the abo

Description : The void ratio of (A) Single size coarse aggregate is roughly 0.45 (B) Graded coarse aggregate is roughly 0.040 (C) Fine aggregate is roughly 0.45 (D) All the above

Last Answer : Answer: Option D

For Unbraced column, the ratio of the clear height of the column to the minimum dimension of the column shall not exceed [ A ] 30 [ B ] 40 [ C ] 50 [ D ] 60

Description : For Unbraced column, the ratio of the clear height of the column to the minimum dimension of the column shall not exceed [ A ] 30 [ B ] 40 [ C ] 50 [ D ] 60

Last Answer : [ A ] 30

For the construction of water bound macadam roads, the correct sequence of operations after spreading coarse aggregates is (A) Dry rolling, wet rolling, application of screening and application of filler (B) Dry rolling, application of filler, wet rolling and application of screening (C) Dry rolling, application of screening, wet rolling and application of filler (D) Dry rolling, application of screening, application of filler and wet rolling

Description : For the construction of water bound macadam roads, the correct sequence of operations after spreading coarse aggregates is (A) Dry rolling, wet rolling, application of screening and application of ... of filler (D) Dry rolling, application of screening, application of filler and wet rolling

Last Answer : Answer: Option C

The size of fine aggregates does not exceed (A) 2.75 mm (B) 3.00 mm (C) 3.75 mm (D) 4.75 mm

Description : The size of fine aggregates does not exceed (A) 2.75 mm (B) 3.00 mm (C) 3.75 mm (D) 4.75 mm

Last Answer : Answer: Option D

The size of fine aggregates does not exceed [ A ] 2.75 mm [ B ] 3.75 mm [ C ] 4.75 mm [ D ] 5.75 mm

Description : The size of fine aggregates does not exceed [ A ] 2.75 mm [ B ] 3.75 mm [ C ] 4.75 mm [ D ] 5.75 mm

Last Answer : [ C ] 4.75 mm

The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2

Description : The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2

Last Answer : Answer: Option D

For the construction of cement concrete dams, the maximum permissible size of the aggregates, is (A) 40 mm (B) 50 mm (C) 60 mm (D) 70 mm

Description : For the construction of cement concrete dams, the maximum permissible size of the aggregates, is (A) 40 mm (B) 50 mm (C) 60 mm (D) 70 mm

Last Answer : Answer: Option A

A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Last Answer : (b) 8 mm diameter

For the construction of cement concrete floor, the maximum permissible size of aggregate, is (A) 4 mm (B) 6 mm (C) 8 mm (D) 10 mm

Description : For the construction of cement concrete floor, the maximum permissible size of aggregate, is (A) 4 mm (B) 6 mm (C) 8 mm (D) 10 mm

Last Answer : Answer: Option D

A pre-stressed concrete member (A) Is made of concrete (B) Is made of reinforced concrete (C) Is stressed after casting (D) Possesses internal stresses

Description : A pre-stressed concrete member (A) Is made of concrete (B) Is made of reinforced concrete (C) Is stressed after casting (D) Possesses internal stresses

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The weight of ingredients of concrete mix, is taken in kilograms (B) Water and aggregates are measured in litres (C) 20 bags of cement make one tonne (D) All the above

Description : Pick up the correct statement from the following: (A) The weight of ingredients of concrete mix, is taken in kilograms (B) Water and aggregates are measured in litres (C) 20 bags of cement make one tonne (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to the shape of the particles, concrete aggregates are classified as rounded irregular, angular and flaky (C) According to the surface texture of the particles, the concrete aggregates are classified as glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Description : Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to ... glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) An increase in water content must be accompanied by an increase in cement content (B) Angular and rough aggregates reduce the workability of the concrete (C) The slump of the concrete mix decreases due to an increase in temperature (D) All the above

Description : Pick up the correct statement from the following: (A) An increase in water content must be accompanied by an increase in cement content (B) Angular and rough aggregates reduce the workability of the ... The slump of the concrete mix decreases due to an increase in temperature (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Water cement paste hardens due to hydration (B) During hardening cement binds the aggregates together (C) Cement provides strength, durability and water tightness to the concrete (D) All the above

Description : Pick up the correct statement from the following: (A) Water cement paste hardens due to hydration (B) During hardening cement binds the aggregates together (C) Cement provides strength, durability and water tightness to the concrete (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The theory of formation of concrete is based on the phenomena of formation of voids (B) The bulking of sand is taken into account while volumetric proportioning of the aggregates (C) The dry sand and the sand completely flooded with water, have practically the same volume (D) All the above

Description : Pick up the correct statement from the following: (A) The theory of formation of concrete is based on the phenomena of formation of voids (B) The bulking of sand is taken into account while ... sand and the sand completely flooded with water, have practically the same volume (D) All the above

Last Answer : Answer: Option D