The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm

The length of the vicat plunger is
(a) 40mm
(b) 60mm
(c) 50mm
(d) 30mm
by

1 Answer

Answer :

(c) 50mm
by

Related questions

For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm

Description : For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm

Last Answer : (a) 40mm

The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Description : The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Last Answer : Answer: Option C

The diameter of the Vicat plunger is 10 mm and its length varies form [ A ] 40 mm [ B ] 50 mm [ C ] 55 mm [ D ] 60 mm

Description : The diameter of the Vicat plunger is 10 mm and its length varies form [ A ] 40 mm [ B ] 50 mm [ C ] 55 mm [ D ] 60 mm

Last Answer : [ B ] 50 mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm

According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above

Description : According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above

Last Answer : [ A ] Shall be not less than 20mm

Vicat apparatus is used for (A) Fineness test (B) Consistency test (C) Test for setting time (D) Test for tensile strength

Description : Vicat apparatus is used for (A) Fineness test (B) Consistency test (C) Test for setting time (D) Test for tensile strength

Last Answer : Answer: Option B

Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa

Description : Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa

Last Answer : Answer: Option B

If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Last Answer : b) 40/9

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

What length of an alloy wire of resistivity 5.0x10^-7 Ωm and diameter 0.50mm is required to make a standard 6.0Ω resistor?

Description : What length of an alloy wire of resistivity 5.0x10^-7 Ωm and diameter 0.50mm is required to make a standard 6.0Ω resistor?

Last Answer : Interesting homework question. I’m not knowledgeable about physics, but putting myself in the shoes of someone who is.. Why don’t you post the answer that you got, and show your work, and ask us where you went wrong on the problem.

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm

Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm

Last Answer : c) 6.1mm

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

If a contractor proposes to increase concrete cover beyond contractual specification (i.e. 40mm to 70mm), shall engineers accept the proposal?

Description : If a contractor proposes to increase concrete cover beyond contractual specification (i.e. 40mm to 70mm), shall engineers accept the proposal?

Last Answer : In contractual aspect, based on the requirement of General Specification of Civil Engineering Works (1992 Edition), the tolerance of concrete cover is between + ... larger cover. Therefore, with an increase of concrete cover, the crack width will increase which is undesirable.

Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse aggregate should not exceed one fifty of the minimum dimension of the reinforced concrete member (c)The aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Description : Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse ... aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Last Answer : (d) All the above

For high degree of workability, the slump value should vary between (a) 0 to 25mm (b) 25 to 50mm (c) 50 to 80mm (d) 80 to 100mm

Description : For high degree of workability, the slump value should vary between (a) 0 to 25mm (b) 25 to 50mm (c) 50 to 80mm (d) 80 to 100mm

Last Answer : (d) 80 to 100mm

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

To assess the surface of a weld for direct inspection, the distance from the surface to eye should be a maximum of? a) 200mm b) 600mm c) 60mm d) 6000mm

Description : To assess the surface of a weld for direct inspection, the distance from the surface to eye should be a maximum of? a) 200mm b) 600mm c) 60mm d) 6000mm

Last Answer : b) 600mm

A hydraulic press has a ram of 15 cm diameter and plunger of 1.5 cm. It is required to lift a weight of 1 tonne. The force required on plunger is equal to (A) 10 kg (B) 100 kg (C) 1000 kg (D) 1 kg

Description : A hydraulic press has a ram of 15 cm diameter and plunger of 1.5 cm. It is required to lift a weight of 1 tonne. The force required on plunger is equal to (A) 10 kg (B) 100 kg (C) 1000 kg (D) 1 kg

Last Answer : Answer: Option A

square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?

Description : square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?

Last Answer : 10001/999900

How many inches is .40mm?

Description : How many inches is .40mm?

Last Answer : 0.015748 inches

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

Nikon Photographers: Can you please recommend me a cheap 50mm lens for a D40?

Description : Nikon Photographers: Can you please recommend me a cheap 50mm lens for a D40?

Last Answer : answer:Great site for exactly what you are looking for. http://lenshero.com/

Photographers: Can you tell me what difference between a 50mm 1.8 and 50mm 2.5 lens for Canon?

Description : Photographers: Can you tell me what difference between a 50mm 1.8 and 50mm 2.5 lens for Canon?

Last Answer : answer:The f1.8 lens (assuming this is a fixed aperture, and not adjustable to different f-stops) will be suitable for work in low-light conditions, since its opening to permit light is larger than an f-2 ... like to do, the higher f-stop lens will give you a deeper depth of field, if only slightly.

I'm looking for a refurbished Canon EF 50mm f/1.4 USM Lens in Canada. Where can I get one?

Description : I'm looking for a refurbished Canon EF 50mm f/1.4 USM Lens in Canada. Where can I get one?

Last Answer : Ebay or BestBuy.

How much does a 50mm nail weigh in grams?

Description : How much does a 50mm nail weigh in grams?

Last Answer : Need answer

How many feet is 50mm?

Description : How many feet is 50mm?

Last Answer : 1 ft = 304.8 mm (exactly)50 mm = 50 ÷ 304.8 ft= 125/762 ft≈ 0.164 ft

How many feet is 50mm?

Description : How many feet is 50mm?

Last Answer : 1 ft = 304.8 mm (exactly)50 mm = 50 ÷ 304.8 ft= 125/762 ft≈ 0.164 ft

Label size of foreign article is min & postage paid words should not be less than a) 70mm X 100mm & 300sq mm b) 50mm X 80mm & 200sq mmc) 25mm X 50 mm & 100 sq mm d) None of these

Description : Label size of foreign article is min & postage paid words should not be less than a) 70mm X 100mm & 300sq mm b) 50mm X 80mm & 200sq mm c) 25mm X 50 mm & 100 sq mm d) None of these

Last Answer : a) 70mm X 100mm & 300sq mm

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code calls for a 4t bend. Which of the following rollers should be selected for the testing? a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter

Description : Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code calls for a 4t bend. Which of the following rollers should be selected for the testing? a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter

Last Answer : d) 32mm diameter

The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Description : The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)

Last Answer : d. 25mm (1 inch)

.The undercut for Cobalt Chrome’s retentive arm clasp is, A. 0.75mm B. 0.50mm C. 0.25mm

Description : .The undercut for Cobalt Chrome’s retentive arm clasp is, A. 0.75mm B. 0.50mm C. 0.25mm

Last Answer : C. 0.25mm

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Explain the different recording techniques used in method study. Also outline process chart for checking diameter of 50mm of shaft.

Description : Explain the different recording techniques used in method study. Also outline process chart for checking diameter of 50mm of shaft.

Last Answer : Different recording techniques used in method study: Process charts are used to record the data systematically so that none of the information needed for study and analysis is missed. A. Chart indicating ... area. However, there is no indication of the direction or speed of motion.

Would you have any problem sticking your hand in your toilet tank to pull the plunger to flush the toilet?

Description : Would you have any problem sticking your hand in your toilet tank to pull the plunger to flush the toilet?

Last Answer : Nope. Done it many times, for various reasons. It’s sticking my hand in the bowl that I would balk at.

What do you do with the plunger when you're done?

Description : What do you do with the plunger when you're done?

Last Answer : Flush toilet clean, dip it a few times in clean water, dip again for good measure then lay it on paper towels or newspaper to dry. What REALLY got to me was when the neighbor across the road came and asked to borrow it!

Plumbing emergency! Draino or a plunger?

Description : Plumbing emergency! Draino or a plunger?

Last Answer : I prefer to bust out the plunger, nothing like the good ol’ plunger.

A syringe has a volume of 10.0 cm^3 at pressure 1 atm. If you plug the end so that no gas can escape and push the plunger down,

Description : A syringe has a volume of 10.0 cm^3 at pressure 1 atm. If you plug the end so that no gas can escape and push the plunger down,

Last Answer : A syringe has a volume of 10.0 cm3 at pressure 1 atm. If you plug the end so that no gas can ... the final volume to change the pressure to 3.5 atm?

What type of plumbing supplies might I need to unclog a toilet that is not responding to a plunger:?

Description : What type of plumbing supplies might I need to unclog a toilet that is not responding to a plunger:?

Last Answer : If you’re plunging make sure to remove the water from the toilet to get the best results. That way you can flush the toilet without it overflowing. You can try using a snake (or plumber’s auger). The ... will grind its way through the clog. If that doesn't work, you may need to call a plumber.

wanted spring loaded plunger castor for stepping stool, who has castor and shaft ,all plastic for light work?

Description : wanted spring loaded plunger castor for stepping stool, who has castor and shaft ,all plastic for light work?

Last Answer : This page has what you want located on it, www.pianobenchesetc.com/store/home.php?cat=1

What is the best style of plunger?

Description : What is the best style of plunger?

Last Answer : A simple plunger will do all you need, no need for any fancy trim.

Dead fish in vaccume clogged plunger not working?

Description : Dead fish in vaccume clogged plunger not working?

Last Answer : This happened to my hamster once

Continuous injection system usually has a) plunger pump b) rotary pump c) gear pump d) vane pump

Description : Continuous injection system usually has a) plunger pump b) rotary pump c) gear pump d) vane pump

Last Answer : Answer: b Explanation: In common use continuous injection system usually has rotary pump.