Define (i) Open circuit (ii) Short circuit.

Define (i) Open circuit (ii) Short circuit.
by

1 Answer

Answer :

Open circuit : An electrical circuit is said to be open,when any part of conducting path is open or broken and there is no continuity in the conducting path of an electrical circuit.

Short circuit : An electrical circuit is said to be short,when voltage source has closed path across its terminal.
by

Related questions

Explain with neat circuit, concept of open circuit and short circuit.

Description : Explain with neat circuit, concept of open circuit and short circuit.

Last Answer : Open Circuit  Two points in a circuit are said to be open circuited if there is no circuit element or direct connection between them. An open circuit exist between points A and B in ... short circuited in below figure. The resistance between short circuited points is zero. RAB= 0Ω

Define linear and non-linear wave-shaping circuit.

Description : Define linear and non-linear wave-shaping circuit.

Last Answer : Linear wave-shaping circuit  The circuit which makes use of only linear circuit elements is known as linear wave shaping circuits. Resistor, capacitor, inductor are used for the circuits. E.g. ... , transistor, resistors and capacitors etc. are used for the circuits. E.g. Clipper, Clamper

Define clipper. Draw circuit of negative shunt clipper.

Description : Define clipper. Draw circuit of negative shunt clipper.

Last Answer : Clipper: A clipper is a device designed to prevent the output of a circuit from exceeding a predetermined voltage level without distorting the remaining part of the applied waveform. OR Clipper: An ... the positive or negative peak or both from a specific level is known as clipper.

Define following terms: i) Active networks. ii) Unilateral networks

Description : Define following terms: i) Active networks. ii) Unilateral networks

Last Answer : i) Active networks: If a network consists of an energy source then it is called an active network. The type of energy source can be a voltage source or a current source. ii) ... direction of current through its elements in it, then the network is called as a unilateral network.

Define : (i) Efficiency (ii) TUF of Rectifier

Description : Define : (i) Efficiency (ii) TUF of Rectifier

Last Answer : Rectifier efficiency (ɳ) : it is defined as the ratio of DC power to the applied input AC power. Transformer utilization factor: It is defined as the ratio of the DC power available at the load resistor and the AC rating of the secondary coil of a transformer.

Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Description : Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Last Answer : Ripple Factor: Ripple Factor is defined as the ratio of RMS value of the AC component of output to the DC or average value of the output. Mathematically it is expressed as, ( ... which appears across non-conducting reverse biased diode. (ii) PIV of diode for bridge rectifier-Vm

Define i)Linear network ii)Non-linear network iii)Bilateral network iv)Unilateral network

Description : Define i)Linear network ii)Non-linear network iii)Bilateral network iv)Unilateral network

Last Answer : Linear Network: If the characteristics, parameter such as resistances, capacitances, inductances etc. remain constant irrespective of changes in temperature, time, voltage etc. then the circuit or network ... current through its elements in it, then the network is called as a unilateral network.

Draw the circuit diagram of bridge rectifier and label it.

Description : Draw the circuit diagram of bridge rectifier and label it. 

Last Answer : Circuit Diagram Bridge rectifier

Draw the clipper circuit using series and shunt diode.

Description : Draw the clipper circuit using series and shunt diode.

Last Answer : Fig: A series negative clipper (OR) Fig: Series positive clipper Fig: Parallel positive clipper (OR) Fig: Parallel negative clipper

Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

With help of circuit diagram and waveform, explain working of positive series clipper.

Description : With help of circuit diagram and waveform, explain working of positive series clipper.

Last Answer : Series Clipper (Positive):-   Working: For positive cycle the diode D is reverse biased. Hence there is no voltage across the load RL While for negative half wave, the diode D is forward biased. Hence ... positive cycle of the input voltage gets clipped off. Input & o/p wave form:-   

With help of circuit diagram and waveform, explain working of CLC or π- filter.

Description : With help of circuit diagram and waveform, explain working of CLC or π- filter.

Last Answer : Circuit diagram CLC or Π filter:   Working : It consist of a filter capacitor C1 connected across the rectifier o/p , a choke L is series and another filter capacitor C2 connected across the load. ... to block. Therefore, only d.c component appears across the load and that is what we desire.  

With help of circuit diagram and waveform, explain shunt capacitor filter.

Description : With help of circuit diagram and waveform, explain shunt capacitor filter.

Last Answer : Circuit diagram and Waveform: OR Explanation: A filter circuit is one which removes the ac component present in the rectified output and allows the dc component to reach the ... which allows ac components. The remaining dc components present in the signal are collected at the output. 

Draw RC differentiator circuit.

Description : Draw RC differentiator circuit.

Last Answer : RC differentiator circuit :

What is need of wave shaping circuit ?

Description : What is need of wave shaping circuit ?

Last Answer : In electronics application, it is often needed to alter the shape of wveform like cutting off positive or negative portion of wave,generation of one wave from other,holding wave at some dc level etc.To do this waveshaping circuits are needed.

With the help of circuit diagram and waveforms, explain working of RC differentiator.

Description : With the help of circuit diagram and waveforms, explain working of RC differentiator.

Last Answer : Fig: RC differentiating circuit Figure shows a RC differential circuit. It is also known as high pass filter. The reactance of a capacitor decreases with increasing frequency. The higher ... i.e. the output signal is directly proportional to the derivative of the input signal.  

Describe working of negative clamper circuit with neat diagram and waveform.

Description : Describe working of negative clamper circuit with neat diagram and waveform.

Last Answer : Working: In the first positive half cycle the capacitor will charge through the forward biased diode to peak voltage Vm as shown in circuit. Charging takes place very quickly as the ... reverse biased and stop conducting. Negative clamper adds a negative DC shift as shown in waveform.

Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram:    

State the necessity of wave-shaping circuit.

Description : State the necessity of wave-shaping circuit.

Last Answer : 1. To limit the voltage level of the waveform to some present value. 2. To shift the waveform to a particular voltage level. 3. To generate one wave from the other. 4. To cut the negative and positive portions of the waveform.

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Draw negative clamper circuit and explain its working.

Description : Draw negative clamper circuit and explain its working. 

Last Answer : Diagram: Working: During the positive half cycle of the input AC signal, the diode is forward biased and hence no signal appears at the output. In forward biased condition, the diode allows ... - 2Vm} which have the same polarity with each other. As a result, the signal shifted downwards. 

Define rectification efficiency. Give its formula.

Description : Define rectification efficiency. Give its formula.

Last Answer : The ratio of output DC power delivered to the load to the applied input AC power is called rectification efficiency. It is denoted by η. η = Output DC power delivered to the load / Input AC power from transformer secondary η = Pdc / Pac

Define permeability and reluctivity of magnetic material.

Description : Define permeability and reluctivity of magnetic material. 

Last Answer : Permeability is the capability of a specific material to allow the flow of magnetic flux more easily. Thus higher permeability enables a material to pass more magnetic flux. Reluctivity is equal to the ratio of the intensity of the magnetic field to the magnetic induction of the material.

Define Ferromagnetic materials. Draw B- H Curve.

Description : Define Ferromagnetic materials. Draw B- H Curve.

Last Answer : Ferromagnetic materials: The materials which possess magnetism in the absence of applied magnetic field is known as ferromagnetic materials.

Define dynamic resistance of diode. State, how it is calculated using forward characteristics of diode.

Description : Define dynamic resistance of diode. State, how it is calculated using forward characteristics of diode.

Last Answer : Definition: The resistance offered by the diode to the AC operating conditions is known as the Dynamic resistance' or Incremental resistance' or AC resistance' of a diode. It is ... Dynamic resistance is actually the reciprocal of the slope of the forward characteristics.

Define Inductor. Draw its symbol.

Description : Define Inductor. Draw its symbol. 

Last Answer : An inductor is a passive electronic component that stores energy in the form of a magnetic field  

Define: (1) Mesh (2) Sign conversion (3) Potential rise (4) Potential Drop

Description : Define: (1) Mesh (2) Sign conversion (3) Potential rise (4) Potential Drop

Last Answer : Mesh: A mesh is a closed path in a circuit with no other paths inside it.  Sign convention: In an electrical circuit, the notation given to the voltage drop across resistance and the ... because current flows from a higher to a lower potential then the potential drop is considered Negative.

Draw V-I characteristics of p-n junction diode? Define static and dynamic resistance of diode.

Description : Draw V-I characteristics of p-n junction diode? Define static and dynamic resistance of diode.

Last Answer : Static Resistance: The resistance offered by a p-n junction diode when it is connected to a DC circuit is called static resistance.  (OR) It is the ratio of DC voltage applied across diode ... The dynamic resistance of a diode is the ratio of change in voltage to the change in current. 

Define clipper and clamper.

Description : Define clipper and clamper.

Last Answer : Clipper: The circuit with which the waveform is shaped by removing (or clipping) a portion of the applied wave is known as a clipper.  Clamper: A circuit that shifts either positive or negative peak ... a clamping circuits or clamper. These circuits are also called D.C. restorer or D.C. inserter

Define rectifier. State its types.

Description : Define rectifier. State its types.

Last Answer : A rectifier is defined as an electronic device which converts alternating (AC) voltage or current into unidirectional/ pulsating (D.C) voltage or current. Types of Rectifier: 1. Half wave rectifier 2. Full wave rectifier a. Centre tapped full wave rectifier b. Full wave bridge rectifier

Define static and dynamic resistance of diode.

Description : Define static and dynamic resistance of diode.

Last Answer : Static resistance (Rf) :Static Resistance of a P-N junction diode is the ratio of forward voltage to forward current.   Dynamic Resistance (rf): Dynamic Resistance of a P-N junction diode ... small change in forward voltage to small change in forward current at a particular operating point.  

Define self-inductance and mutual inductance.

Description : Define self-inductance and mutual inductance.

Last Answer : Self-inductance: As per the Lenz's law, the self-inducedemf opposes any current change taking place. This property of the coil to oppose any change in current flowing through it is known as the self- ... in the other coil placed nearby, by induction. It is denoted by M and measured in Henry.  

Draw BH Curve and define coercivity and reluctivity.

Description : Draw BH Curve and define coercivity and reluctivity.

Last Answer : BH Curve: Definitions: Coercivity: For ferromagnetic material the coercivity is the intensity of the applied magnetic field required to reduce the magnetization of that material to zero after the ... to the ratio of intensity of the magnetic field to the magnetic induction of the material. 

Define self and mutual induced emf.

Description : Define self and mutual induced emf.

Last Answer : Self-induced emf: Self-induced emf is the e.m.f induced in the coil due to the change of flux produced by linking it with its own turns. Mutual induced emf: The emf induced in a coil due to the change of flux produced by another neighbouring coil linking to it, is called Mutually Induced emf.   

Define ferromagnetic and ferrimagnetic materials.

Description : Define ferromagnetic and ferrimagnetic materials.

Last Answer : Ferromagnetic materials: The materials which possess magnetism in the absence of applied magnetic field is known as ferromagnetic materials. Example: iron, nickel, cobalt Ferrimagnetic ... a spontaneous magnetization. Example: Magnetite, Ferrous ferrite, Nickel ferrite, Manganese ferrite.

Define active and passive network.

Description : Define active and passive network. 

Last Answer : Active network :If a network consists of an energy source, then it is called as an active network. The type of energy source can be voltage source or a current source.  Passive network : If a network does not contain any energy source then it is called as the passive network. 

State : (i) Norton’s theorem. (ii) super-position theorem.

Description : State : (i) Norton’s theorem. (ii) super-position theorem.

Last Answer : Norton's theorem Statement: Any linear, active, resistive, network containing one or more voltage and / or current sources can be replaced by an equivalent circuit containing a current source ... response (current) caused by individual sources acting alone, while the other sources are inoperative.

Compare ; i) Active n/w and passive n/w ii) Bilateral n/w and unilateral n/w

Description : Compare ; i) Active n/w and passive n/w ii) Bilateral n/w and unilateral n/w

Last Answer : i) Active n/w and passive n/w  Sr.No. Active n/w Passive n/w 1 It is a network which contains active elements. It is a network which does not contains active elements or ... allows the current to flow only in one direction. 2 Eg: transmission line Eg: Diode rectifier

Which material is used for manufacturing of following LED ? (i) Infrared LED (ii) Red or Green LED (ii) Red or Yellow LED (iv) Blue LED

Description : Which material is used for manufacturing of following LED ? (i) Infrared LED (ii) Red or Green LED (ii) Red or Yellow LED (iv) Blue LED

Last Answer : Infrared LED : Aluminum gallium arsenide (AlGaAs) Red or Green LED: Indium gallium nitride (InGaN), Aluminum gallium arsenide (AlGaAs) Red or Yellow LED : Aluminum gallium indium phosphide (AlGaInP), Aluminum gallium arsenide (AlGaAs) Blue LED : Indium gallium nitride (InGaN)

Draw symbol of (i) Tunnel diode (ii) LED

Description : Draw symbol of (i) Tunnel diode (ii) LED

Last Answer : (i) Tunnel diode: (ii) LED:

Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Description : Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Last Answer :  Iron core inductor:  Ferrite core inductor:  

List two applications of i) clipper ii) clamper.

Description : List two applications of i) clipper ii) clamper.

Last Answer : Clipper:  1. Diode clamp 2. wave shaping circuits 3. Clippers can be used as voltage limiters and amplitude selectors. Clamper:  1. Voltage Multipliers 2. For the protection of the ... can be used for removing the distortions 4. For improving the overdrive recovery time clampers are used.

Write two applications of i) LED ii) photodiode.

Description : Write two applications of i) LED ii) photodiode.

Last Answer : LED:   1. In the opto- couplers.  2. In the infrared remote controls.  3. As indicators in various electronic circuits.  4. In seven segment and alphanumeric displays.  5. In optical switching ... As photo (light) detector.  5. In light intensity meters.  6. In the object counting system. 

Draw construction of PVC gang capacitor and describe it’s working.

Description : Draw construction of PVC gang capacitor and describe it’s working.

Last Answer :  Diagram Working  In plastic core capacitor, poly-vinyl chloride (PVC) type of plastic film is used as dielectric between the fixed & movable vanes instead of air. This increases ... & results in great reduction of size of capacitor in comparison with the air core capacitor.

Describe construction of Aluminium Electrolytic capacitor.

Description : Describe construction of Aluminium Electrolytic capacitor.

Last Answer : A plain foil dry electrolytic capacitor is made by forming a coating of aluminium oxide on both sides of an aluminium foil. Two strips of aluminium foil used are then separated by two layers of porous ... is rolled up the ends closed with wax and then sealed into an aluminium container.

List two applications of LDR.

Description : List two applications of LDR.

Last Answer : 1. It is used for automatic contrast of brightness control in television receivers. 2. It is used as a proximity switch. 3. It is used in the street light control circuits. 4. It is used in the ... security alarms. 9. It is used in the smoke detectors. 10. It is used in the infrared astronomy.

Explain the working principle of slug tuned inductor.

Description : Explain the working principle of slug tuned inductor.

Last Answer : The value of inductor increases, when the slug (moving coil) is moved into the coil winding and hence decreases the resonant frequency of the tuned circuit. Similarly, when the slug is moved out of the ... be varied by using movable core which can be moved up or down by using screw driver.

Draw the star and delta connection. State any one conversion formula.

Description : Draw the star and delta connection. State any one conversion formula.

Last Answer : star and delta connection

Explain the following terms 1. Bilateral Network 2. Linear Network

Description : Explain the following terms 1. Bilateral Network 2. Linear Network

Last Answer : Bilateral Network If the magnitude of current flowing through a circuit element is not affected when the polarity of the applied voltage is changed, then the element is known as a bilateral element. ... network comprising of one or more linear number of elements is known as a linear network.

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics